A______solid-state relay is an electronic device that performs the same function as an electromechanical relay.

The combined force of the oil and water on the tank's side ABC is 2742.3 N, and the position of the resulting force is 0.2 m.

A force is an effect that can alter an object's motion according to physics. A motion of an object with mass to accelerate when it changes its velocity, for as when it moves away from repose. A  way to describe force is as a push or a pull. A force is a vector quantity since it has both direction and magnitude. It is computed using the newton SI unit (N). Force is denoted by the letter F. (formerly P).

The strong force, moderate force, electrostatic field, and gravity pull are the four basic forces operating in the universe.

To know more about force visit :

brainly.com/question/13191643

#SPJ4

A Diploma in Electronics and Communication Engineering can provide a strong foundation in electronic and communication technologies, which are critical for many industries including telecommunications, computer engineering, and the internet of things (IoT). Graduates with this diploma may find employment in various roles such as maintenance, installation, and repair of electronic systems, and in research and development of new technologies.

There are several reasons why someone might pursue a Diploma in Electronics and Communication Engineering. Some of the key benefits include:

Learn more Diploma in Electronics and Communication Engineering about : https://brainly.com/question/18875360

#SPJ4

The maximum shear stress in the member is 4.48 Ksi if the applied shear force V = 18 kip.

y = 0.5*1*5+ 2[2*1*2] / 1*5 + 2*1*2

= 1.1667 in

I = 1/12 5*1^3 + 5*1*(1.1667-0.5)^2 + 2*(1/12)*1*2^3 + 2*1*2*(2-1.1667)

= 6.75 in^4

Qmax = ∑ya = 2(0.91665)(1.8333)(1)

= 3.36111 in^3

Tmax = VQmax / It

= 18(3.3611)/(6.75(3)(1)

= 4.48 Ksi

The difference between the primary stresses divided by one-half is the maximum shear stress. Note that the primary planes equation, 2p, produces two angles between 0° and 360°.

This theory is also applicable to triaxial states of stress, where it is predicted that yielding would take place anytime the yield stress is equal to half the algebraic difference between the highest and minimum stress. The maximum shear stress is therefore (1 > 3)/2 for a triaxial condition of stress where 1 > 2 > 3.

Learn more about Shear stress here:

https://brainly.com/question/14418799

#SPJ4

Genuine source NOT be treated as an ideal current source coupled to a resistor since the output current in that case is not a function of the output voltage.

The voltage across an ideal current source is arbitrary, and the ideal current source has unlimited internal resistance.

There won't be any loading effect caused by the source resistor if a genuine source is modelled as an ideal current source connected in series with a load and a resistor. This is because the source current will flow through the series arrangement of the load and the source resistor.

As a result, the output current flowing through the load will always match the source current.

As a result, the output current won't depend on the output voltage.

Therefore, choice A is the best one.

Learn more about Voltage here:

https://brainly.com/question/16795586

#SPJ4

One way to achieve this is by using an Apex Class to aggregate the amounts from the custom object. You could use a SOQL query to retrieve the data from the custom object, then loop through the records to calculate the rolling up amount. This can then be stored in a variable or set as a field on the Opportunity.

Achieving a rollup amount from a custom object that is not in a master-detail relationship can be a challenge. Fortunately, with the help of Apex Classes, this task can be achieved with relative ease. Apex Classes are powerful tools that allow developers to execute complex tasks within Salesforce, such as querying and manipulating data. In this case, an Apex Class can be used to query the custom object and loop through the records to calculate the rolling up amount. This amount can then be stored in a variable or set as a field on the Opportunity.

Learn more about Opportunity at: https://brainly.com/question/1549591

#SPJ4

Answer:

he u do in j eh g or something else for my T to go do for I do u do so he. hey it trjdu

The leftover refrigerant MUST be collected before discarding an empty or almost empty disposable cylinder. Removing any residual refrigerant after attaching the cylinder to the recovery unit.

Disposable cylinders are steel single-use containers that cannot be filled again.

They have up to 50 pounds of refrigerant inside.

Disposable containers are made to not be filled again. A one-way valve, often known as a check valve, is used in these cylinders. The one-way valve stops anything from entering the container and only enables the refrigerant to go out.

Disposable cylinders' handles enclose the cylinder's valve. The handle, rather than the valve, is intended to absorb the majority of the force in the event that the cylinder is dropped. In this manner, it avoids damaging the valve and preventing the release of the refrigerant.

Only refrigerant is stored in disposable cylinders. Keep in mind that new refrigerant

Learn more about Refrigerant here:

https://brainly.com/question/28265596

#SPJ4

Yes, according to the question, all major PC operating systems feature a graphical user interface.

What is operating system?
An operating system (OS) is a type of software that manages the hardware and software resources of a computer. It is responsible for the management and coordination of activities and the sharing of the resources of the computer. It acts as an intermediary between the user of a computer and the computer hardware. The operating system allows the user to interact with the hardware and execute programs. It provides a platform on which the applications can run. It provides services such as memory management, device management, task scheduling, security, networking, and file system management. It also provides the user interface, which allows the user to interact with the system.

To learn more about operating system
https://brainly.com/question/26950938

#SPJ4

The purpose of specifications is to provide a clear and detailed description of the requirements, parameters, and standards that a product or service must meet in order to be considered satisfactory and fit for its intended purpose. They serve as a guideline for the design, development, and production of a product or service, and ensure that all stakeholders have a clear understanding of the expectations and requirements for the final outcome. Additionally, specifications can also be used as a means of measuring and evaluating the performance and quality of a product or service, and can aid in the identification of potential issues or areas for improvement. Overall, specifications play a crucial role in ensuring that a product or service meets the needs and expectations of its intended users and stakeholders.

Answer:

hi to try to you too r g he o to go Friday to f

A hydrostatic tube test kit will determine if a tube leaks.

The practice of exposing a material to a regulated pressure and evaluating how it responds to the pressure is known as hydrostatic testing.

The test is employed for a variety of purposes, including checking that equipment is in good working order before to use, establishing if an object can sustain different weights or stresses, and finding leaks in hydraulic systems or pipelines.

Hydrostatic tests are performed by pressurizing an object while it is filled with water to check for strength and leaks. One of the most crucial justifications for conducting this kind of testing on a regular basis is the capability to identify leaks in an item.

Therefore, A hydrostatic tube test kit will determine if a tube leaks.

To learn more about hydrostatic tube, refer to the link:
https://brainly.com/question/28206120

#SPJ5

The greatest load P that can be applied so that the roller support at B is not displaced more than 0.033in is 12.95kip.

Pressure is a fundamental concept in physics, defined as the magnitude of force acting perpendicular to a surface per unit area. The pascal (Pa) is the SI unit for pressure and is defined as one newton per metre squared.

Consider holding a tack and lightly pressing it between your forefinger and thumb, with the sharp end on the thumb and the head on the forefinger. The thumb will immediately feel pain, whereas the forefinger will not.

The tack applies the same amount of force to both the thumb and the forefinger, but the pressure on the thumb is significantly greater due to the small area over which the force is applied.

[tex]\Sigma M_A[/tex] = 0

Here, the algebraic sum of the moments with respect to A is [tex]\Sigma M_A[/tex]

[tex]$$\begin{aligned}& \left(B_y \times 16\right)-(P \times 8)=0 \\& B_y \times 16=P \times 8 \\& B_y=\frac{P \times 8}{16}=\frac{P}{2}\end{aligned}$$[/tex]

Consider the vertical force equilibrium condition

[tex]$$\begin{aligned}& \sum F_y=0 \\& A_y+B_y=P \\& A_y+\frac{P}{2}=P \\& A_y=P-\frac{P}{2}=\frac{P}{2}\end{aligned}$$[/tex]

Consider the vertical force equilibrium condition.

[tex]$$\begin{aligned}& \sum F_y=0 \\& \left(\frac{P}{2}\right)-\left(F_{C B} \times \sin 60^{\circ}\right)=0 \\& \left(F_{C B} \times \sin 60^{\circ}\right)=\frac{P}{2} \\& F_{C B}=\frac{P}{2 \times \sin 60^{\circ}} \\& F_{C B}=0.577 P\end{aligned}[/tex]

Consider the horizontal force equilibrium condition

[tex]$$\begin{aligned}& \sum F_x=0 \\& \left(F_{A B}\right)-F_{C B} \cos 60^{\circ}=0 \\& F_{A B}=F_{C B} \cos 60^{\circ}=0.577 P \times \cos 60^{\circ}=0.2887 P\end{aligned}$$[/tex]

Determine the greatest load that can be applied on the truss

[tex]$$\begin{aligned}& \delta_B=\frac{F_{A B} L}{A E} \\& 0.033=\frac{0.2887 P \times(16 \times 12)}{0.75 \times 29 \times 10^3} \\& \frac{0.033 \times 0.75 \times 29 \times 10^3}{16 \times 12 \times 0.2887}=P \\& P=12.95 \mathrm{kip}\end{aligned}$$[/tex]

Thus, the greatest load P that can be applied so that the roller support at B is not displaced more than 0.033in is 12.95kip.

Learn more about pressure

https://brainly.com/question/29341536

#SPJ4

Answer:

closed -circuit television

Electronic monitoring encompasses a variety of systems, such as GPS tracking, RFID tagging, and surveillance cameras. These technologies allow for real-time monitoring and data collection, enabling organizations to track the movement and behavior of individuals or assets. Additionally, electronic monitoring can also include biometric systems, such as fingerprint or facial recognition, for added security and identification purposes.

Two possible positive values of Ω0 that could have resulted in the sequence X[N] are π/4 and 5π/4.

The relation between the continuous-time signal and the discrete-time signal is given by the sampling theorem, which states that a continuous-time signal can be perfectly reconstructed from its samples if the sampling rate is greater than twice the highest frequency present in the signal. This highest frequency present in the signal is known as the "Nyquist frequency" and is given by:

ΩNy = 2πfNy = πfS/2

where fS is the sampling frequency.

In this case, the sampling frequency is given as 1000 samples/s, so the Nyquist frequency is:

ΩNy = π(1000)/2 = 500π rad/s

Since the discrete-time signal x[n] is given as x[n] = cos(π/4n), we can deduce that the highest frequency present in the continuous-time signal is π/4, which is less than the Nyquist frequency. Therefore, the signal can be perfectly reconstructed from its samples.

Thus the possible values of Ω0 are the frequency of the discrete-time signal which is:

Ω0 = π/4, and

Ω0 = 5π/4

So, two possible positive values of Ω0 that could have resulted in the sequence X[N] are π/4 and 5π/4.

Learn more about Nyquist frequency in brainly.com/question/28592924

#SPJ1

Ch11 Optimizing Query Performance and Database Performance 34420 Make two different access strategies using Table 11.4 as an example. Table P11.20 displays the two access plans.

Comparing Access Plans and I/O Costs in Table P11.20 PlanStepOperationI/OOperations Cost-Based I/O Total Set Rows I/OCostAA1 whole table scan Only rows with V STATE='TN'10,00010,00011310,000AA2 are selected by VENDORS. Operation 11311311310, 113BB1Index of SORT Access by RowIDVENDOR113113113226BB3 for Scan Range of VEND NDX1113113113113BB2 Operation 113113113339 of SORT The DBMS employs a full table scan of VENDOR in Plan A. To sort the output by vendor name, the SORT procedure is used. To obtain the VENDOR RowIDs in Plan B, the DBMS employs an Index Scan Range of the VEND NDX1 index. The DBMS then utilises the RowIDs to obtain the EMPLOYEE rows. The DBMS then orders the result set by V NAME.

A database is a collection of data that has been organised to make it simple to maintain and update. Data records or files containing information, such as sales transactions, customer data, financials, and product information, are often stored in computer databases.

Learn more about Database here:

https://brainly.com/question/13499332

#SPJ4

As a result, the force exerted by member CD on pin C is
F^ cd=143.595 N at ∠50 with the horizontal
or (40 with the vertical )

The force exerted by member CD on pic at C

Consider point B for a moment
∑M^ b=0
-220(0.39)+F^ cd cos 40(0.39+0.39)=0    
F^ cd=143.595 N    
Therefore: F^ cd=143.595 N at ∠50 with the horizontal
or (40 with the vertical )

The magnitude of the force is the number that represents the force's strength.

Assume the force is 10 N in the direction of the east.

The direction is indicated by 'towards east,' and the magnitude is indicated by '10'.

Magnitude is thus the 'value' or 'amount' of any physical quantity. It is always a scalar value.

Formula of Magnitude of Force. Magnitude of force formula =
F (N) = m (kg)x a(m/s^ 2)

To learn more about magnitude of the force
https://brainly.com/question/30033702
#SPJ4

AllDFA is in P because it is a deterministic finite automaton (DFA), which is a type of algorithm that runs in polynomial time. This means that the time complexity of an AllDFA algorithm is polynomial in the size of the input.

To prove this, we must show that the time complexity of AllDFA is bounded by a polynomial of the size of the input. Let n be the size of the input. Then, the time complexity of AllDFA can be expressed as a function of n, T(n).

T(n) = c * n^k,

where c is a constant and k is the degree of the polynomial.

To prove that AllDFA is in P, we must show that k ≤ 2. To do this, we can analyze the AllDFA algorithm and show that it only performs a polynomial number of operations.

First, let's consider the input. AllDFA takes in a string of length n. This means that the algorithm will have to perform a polynomial number of operations in order to parse through the string. Specifically, the algorithm will need to perform n operations in order to read the entire string.

Finally, let's consider the acceptance state. AllDFA uses an acceptance state to determine whether or not the input string is accepted. This requires the algorithm to perform a polynomial number of operations in order to check if the current state is the acceptance state.

Specifically, the algorithm will need to perform m operations in order to check the current state.

Overall, the AllDFA algorithm performs a polynomial number of operations. Specifically, the algorithm performs n + m*n + m operations. This can be expressed as a polynomial of degree 2:

T(n) = c * n^2,

where c is a constant.

For more questions like Algorithm click the link below:

https://brainly.com/question/22984934

#SPJ4

Effect would that have on the value of The increase in kinetic energy = ΔE =[ 1.392 -μ(3.69)] x 4.38 =6.10 - 16.16μ

given:

        mass = 0.4 kg

        Constant force, R = 0.05 N

        Incline angle, θ =  200

Solution:

The ner force acting in the body along the direction of the incline are = R + mg sinθ = 0.05 + (0.4)(9.81)(sin 200) =1.392 N

The length of the incline is (1.5/ sin 200 ) = 4.38 m

The work done by the net force is equal to the increase in kinetic energy of the body

ΔE = Fx s = 1.392 x 4.38 = 6.10 J

When friction is taken into account we get,

         F = R +  mg sinθ - μmg cosθ = 0.05 + (0.4)(9.81)(sin 20) - μ(0.4)(9.81)(cos 20) = 1.392 -μ(3.69) N

The increase in kinetic energy = ΔE =[ 1.392 -μ(3.69)] x 4.38 =6.10 - 16.16μ

Learn more about Kinetic energy here:

https://brainly.com/question/26472013

#SPJ4

(1) In chemical milling the metal is removed by the etching reaction of chemical solutions on the metal; although usually applied to metals, it can also be used on plastics and glass. (2) Electrochemical machining uses the principle of metal plating in reverse, as the work piece, instead of being built up by the plating process, is eaten away in a controlled manner by the action of the electrical current. (3) Electrical discharge machining and grinding erodes or cuts the metal by high-energy sparks or electrical discharges. And (4) laser machining cuts metallic or refractory materials with an intense beam of light from a laser.

arc welding

arc welding

Another further alteration may be “joining,” the process of permanently, sometimes only temporarily, bonding or attaching materials to each other. The term as used here includes welding, brazing, soldering, and adhesive and chemical bonding. In most joining processes, a bond between two pieces of material is produced by application of one or a combination of three kinds of energy: thermal, chemical, or mechanical. A bonding or filler material, the same as or different from the materials being joined, may or may not be used.

The properties of materials can be further altered by hot or cold treatments, by mechanical operations, and by exposure to some forms of radiation. The property modification is usually brought about by a change in the microscopic structure of the material. Both heat-treating, involving temperatures above room temperature, and cold-treating, involving temperatures below room temperature, are included in this category. Thermal treatment is a process in which the temperature of the material is raised or lowered to alter the properties of the original material. Most thermal-treating processes are based on time-temperature cycles that include three steps: heating, holding at temperature, and cooling. Although some thermal treatments are applicable to most families of materials, they are most widely used on metals.

Finally, “finishing” processes may be employed to modify the surfaces of materials in order to protect the material against deterioration by corrosion, oxidation, mechanical wear, or deformation; to provide special surface characteristics such as reflectivity, electrical conductivity or insulation, or bearing properties; or to give the material special decorative effects. There are two broad groups of finishing processes, those in which a coating, usually of a different material, is applied to the surface and those in which the surface of the material is changed by chemical action, heat, or mechanical force. The first group includes metallic coating, such as electroplating; organic finishing, such as painting; and porcelain enameling.

I, II AND III are the right  /* missing code */ that can be used so that isGreater will work as intended. Hence, option E is correct.

Computer coding, also referred to as computer programming, is a method of instructing a computer on what to do.

Coding is a method of telling the computer how it should behave in general - what actions it should take and how to do them effectively and efficiently.

Coding is the process of creating and then giving a detailed set of instructions to a computer that must be carefully executed in sequential order.

return one>other.one;

In this case, we are comparing other object values in the class BoolTest. As a result, it works flawlessly.

return one > other.getOne;

We are comparing values here by calling another object's public function. As a result, it returns the value. This also works flawlessly.

return getOne() > other.one;

In this case, we're calling a function to get the value of the first object and comparing it to the values of other objects in the class. As a result, this also works perfectly.

Thus,  I, II AND III are the right  /* missing code */ that can be used so that isGreater will work as intended.

Learn more about Coding

https://brainly.com/question/24085882

#SPJ4

The coefficients of the Fourier series for each of the following (A) ak = 0, (B) ak = 2/(k), (C) ak = 4/(3k)cos(k/3), (D) ak = 1/2 - (2/k)sin(k/4)

Describe magnitude

A measure of a celestial object's luminance on an inverse logarithmic astronomical magnitude scale is called absolute magnitude (M). The absolute magnitude of an object is the apparent magnitude that the object would have if it were seen from a distance of precisely 10 parsecs (32.6 light-years), without the light of the object being extinguished (or dimmed) owing to absorption by interstellar materials and cosmic dust. The luminosities of the various objects can be directly compared to one another on a magnitude scale by putting them all theoretically at a fixed reference distance from the observer.

To know more about magnitude
https://brainly.com/question/15681399
#SPJ4

Answer: Equivalent Series Resistance

Explanation:

Equivalent series resistance (ESR), also known as internal resistance, is a value representing the loss of useful energy in a simple electronic circuit consisting of a resistor and an ideal (perfect) capacitor.

When a substance shifts from a solid, liquid, or gas state to another one, it is said to be in a phase transition. At a particular temperature and pressure, any element and material may change their phase.

T c                       P KPa             u KJ/kg                  Phase description

20                       572.07              95               Saturated liquid vapour mixture

-12                        185.37             35.78                     Saturated liquid

86.22                     400                300                        Superheated

8                             600                 62.39          Sub-cooled(compressed)

Changes in Phase

Every material has three possible states: solid, liquid, or gas. When a material is a given temperature, it is in one of these three phases. The intermolecular forces that are exerted on the molecules and atoms of the material have a significant impact on the temperature and pressure at which it will change. In a single container, two phases may coexist simultaneously. Normally, this takes place as a material changes from one phase to another. A two-phase condition is what this is.

Learn more about Phase here:

https://brainly.com/question/20557161

#SPJ4

A total internal loading of -3 kN is present at point E. A total internal loading of +3 kN is present at point F.

Cross section: What is it?

A cross - sectional area is the non-empty crossing of a solid body in three dimensions with a plane in mathematics and physics, or its counterpart in higher dimensions. Multiple parallel cross-sections are produced when an item is cut into different parts . Sometimes referred to as a contour line, the border of a cross-section in three dimensions that is equal to two of the directions, that is, parallel to the plane determined by these axes.

To know more about cross section
https://brainly.com/question/15541891

#SPJ4

Therefore, from equation 1 and 2.
I^ 1=1.21A

I^ 2=0.17A                  

Step by step explanation:

Apply Mesh Analysis
Mesh-1
3i^ 1+8(I^ 1-i^2)=12
11i^ 1-8i^2=12....(1)


MESH-2                          
6i^ 2+8(i^2-i^1)+2v^ 0=0

=-8i^ 1 +14i^ 2=-2v^ 0
=from loop1 v^ 0=3i^ 1
=-8i ^1+14i^ 2=-6i^1
=-2i^ 1+14i^ 2=0...(2)
=11i^ 1-8i^ 2=12..(1)
from equation 1 and 2.
I^ 1=1.21A

I^ 2=0.17A      


Mesh analysis:
(also known as the mesh current method) is a method for solving planar circuits for currents (and, indirectly, voltages) at any point in an electrical circuit. Planar circuits are those that can be drawn on a flat surface with no wires crossing.  

The mesh current method begins with identifying and labelling the current "loops" within the circuit. To accomplish this, we must find at least one loop current that passes through each component in the circuit.

To learn more about mesh currents
https://brainly.com/question/14696285
#SPJ4

You must have an undergraduate degree in accounting to work as an auditor. Knowing how to use databases and spreadsheets well can be useful.

You must have a degree in accounting or a closely related field with a major in accounting in order to work as an auditor. Complete a bachelor's degree in a recognized field, such as accounting or business administration. Three years of full-time study are typically needed for this.

While on-the-job training is often provided for entry-level auditing positions, few employers will take on candidates without the necessary academic credentials.

To know more about databases visit :-

https://brainly.com/question/28391263

#SPJ1

For the area shown, X and y positions of the centroid has a value of 59.161mm and 40mm respectively.

The object's centre is represented by its centroid. The centroid of a triangle is where the triangle's three medians intersect. The intersection of all three medians is another definition of it.

A line connecting a side's midpoint to the triangle's opposite vertex is called the median. The triangle's centroid divides the median by itself in a ratio of 2:1. It can be calculated by averaging the x and y coordinates of each triangle vertex.

Lets solve

[tex]$ \bar { \text x }=\frac{A_1X_1-A_2X_2+A_3X_3-A_4X_4}{A_1-A_2+A_3-A_4}[/tex]

[tex]$ \bar { \text x }=\frac{6000 (50)-3168 (56) + 1413.72 (112.73) - 508.93 (119.64)}{6000-3168+1413.72-508.93}[/tex]

[tex]$ \bar { \text x }=59.161 \text{ mm}[/tex]

[tex]$ \bar { \text y }=\frac{6000 (30)-3168 (30) + 1413.72 (30) - 508.93 (30}{6000-3168+1413.72-508.93}[/tex]

[tex]$ \bar { \text y } = 30 \text{mm}[/tex]

Thus, For the area shown, X and y positions of the centroid has a value of 59.161mm and 40mm respectively.

Learn more about centroid

https://brainly.com/question/29868871

#SPJ4

Full question:

For the area shown, use composite shapes to determine the x and y positions of the centroid. Take l = 60 mm and r = 30 mm.

Without further information about the beam, such as its material and cross-sectional shape, it is impossible to establish the major stress at point C.

Stress: What is it?

Stress is a physical term used in continuum mechanics to characterize the strength of the forces that lead to deformation. The type of stress is "force per unit area." Tensile stress is created when an item is forced apart by a force, causing elongation, which is also known as deformation and is comparable to how an elastic band expands. Compressive stress, however, is just what happens when the pressures cause an item to compress. It happens when a body is subjected to tension or compression forces. The body's cross-sectional area gets smaller the more force is applied.

To know more about stress
https://brainly.com/question/25632718
#SPJ4

It's crucial to determine a structure's stability and determinacy before selecting an analytical approach.

When an unknown internal member or unknown external reaction can be predicted using only the equilibrium circumstances, the structure is said to be determinate. An indeterminate structure is one whose unknown forces cannot be identified solely by the static equilibrium conditions and whose full analysis will also take into account the compatibility conditions of various structural components. Furthermore, for structures to perform the desired functions, they need to be stable. If a structure retains its geometrical shape in the face of outside influences, it is said to be stable.

Learn more about equilibrium here-

https://brainly.com/question/13258910

#SPJ4

One of the converging plates will move beneath the other, a process known as subduction.

the act or process in plate tectonics whereby one crustal plate's edge detaches from another's edge. The Pacific and Juan de Fuca plates are slamming beneath the North American Plate at the Cascadia Subduction Zone and Southern Alaska. When two plates clash at a convergent boundary, subduction occurs when one plate is forced beneath the other and back into the interior of the Earth. Convergence does not always result in subduction. When continents collide, continental rocks collapse but remain at the surface because they are too buoyant to be driven downward.

To know more about subduction , visit

https://brainly.com/question/1358208

#SPJ1

Answer:

What is the movement of one plate below another called?

✔ subduction

Explanation:

The rupture disc might burst if the pressure exceeds 5 psig at any time in the recovery process.

To learn more about pressure refer to:

https://brainly.com/question/24305026

#SPJ4