It means:
"Do Not Pass." When parking near a corner, you may park your vehicle no closer than 20 feet from a crosswalk.
<3
Which of the following best describes maintenance?
A) Making repairs as directed by a pinpoint test
B) The act of keeping a vehicle in good operating condition
C) servicing items that are worn
D) performing the service needed to fix a concern
Answer:
Equipment Reliability and Maintenance
SUBSTANTIAL CAPITAL investments, in the form of facilities and equipment, are required for manufacturing almost all goods of economic significance. The productivity of these investments is a fundamental element of competition among companies and nations. Events that slow or interrupt the manufacturing process or degrade the product impair the competitiveness of a manufacturing enterprise.
The term equipment reliability and maintenance (ERM) encompasses not only equipment, such as machines, tools, and fixtures, but also the technical, operational, and management activities, ranging from equipment specifications to daily operation and maintenance, required to sustain the performance of manufacturing equipment throughout its useful life. This chapter addresses all causes of diminished or degraded output. The panel considers ERM to be a significant factor in the competitiveness of manufacturing firms, an assessment supported by the case studies in the section on present practice (pp. 57-63).
Historically, the evolution of ERM can be traced from breakdown maintenance and repair to preventive maintenance to predictive maintenance. Breakdown maintenance and repair is the after-the-fact restoration of failed equipment. Preventive maintenance is the systematic servicing of equipment to reduce the possibility of failure. Predictive maintenance, in use in U.S. industry for only four or five years, is usually understood to involve the use of computer software to detect conditions that might eventually lead
5. How is the hydrogen gas balloon different from the hot air balloon? explain this in terms of density
Answer:
either helium or hydrogen
Answer:
As air is heated, it becomes less dense than the surrounding cooler air. The less dense hot air has enough lifting power to cause the balloon to float and rise into the air.
Explanation:
Question 9 (1 point)
In the Standard Automotive Tire Designation P205/65R 15 94 T, the ________ is 94.
a)Load Index
b)Tread Height
c)Speed Rating
d)Wheel Height
Answer:
The Load Capacity is 94
Explanation:
I hope this helps!
SUBJECT : SCIENCE
the change in temperature will not be the same for all substances assuming that the same amount of heat is added or subtracted because
because not all substances react the same to temperature changes. If you heat a metal and an organic substance and you turn the temperature up, the organic substance like water will react (boil) while most metals need higher temperature to react.
what is the name of the flap on the horizontal stabilizer
Swag Answer:
They are called elevators
Swag Explanation :
They are called that for whatever reason mAsqUErADE MaSquerade tHat iS mY nAmE
Hey answer quick for 20 points
Answer:
Hey.....Thanks but FYI this is only 8 points....If u want to put 20....try putting 40...Gilberto wants to take out a loan for college, but he does not want the interest to accrue until after he graduates. Which loan should he apply for?
Question
The CNC is the primary interface between the machine operator and the machine. Is this statement TRUE or FALSE?
True
False
Answer:
True
Explanation:
The CNC is the primary interface between the machine operator and the machine.
23.6 Of the three possible modes by which a cutting tool can fail during a machining operation, which one is most preferable: (a) fracture failure, (b) gradual wear, or (c) temperature failure
Answer:
b) gradual wear
Explanation:
EverFi future smart pie chart
Bond: 20%
Mutual fund: 15%
Stock: 50%
Savngs account: 15%
Answer:
wow!!!!!! you pie chart is sweet
The representation of the following data in a pie chart is given in the diagram;
Bond: 20%Mutual fund: 15%Stock: 50%Savngs account: 15%What is pie chart?
A pie chart is a circle which is used for the diagramatic representation of data. It is usually done by dividing the circle into different areas or slices to represent each data.
Each slice could be used to represent different units such as degree, percentage, centimeters, kilograms.
Bond: 20%
Mutual fund: 15%
Stock: 50%
Savngs account: 15%
Total = 20% + 15% + 50% + 15%
= 100%
Learn more about pie chart:
https://brainly.com/question/796269
#SPJ2
Mark has a baking tray with 24 muffins the muffins are arranged in 4 rows how many muffins are in each row
Answer:
6
Explanation:
I know this because if you divide 24 by 4 you get 6
“We have to redo the deck we built last week,” Bennett tells his coworkers. “I just tested it, and it doesn’t hold the minimum weight that the county requires. We have to replace it even though the client likes it as is and fixing it will cost us money.” What type of behavior is this?
A.
needs-driven
B.
consumer-driven
C.
emotional
D.
ethical
Answer:
Consumer-driven
Explanation:
Bcz he told the cost of money
an HV battery radiator has intake air routed through the cooling fins of the ____ or heat exchanger before it circulates over the battery packs
Answer:
While inspecting the vehicle when it is hot, it is found to have excessive coolant in the coolant recovery container. After the engine cools the level returns to normal. Tech A says that this could be caused by a restriction in the radiator.
Explanation:
Working upward from the stove, the worker just installed K2654. What part should be installed next?
Answer: adapter J44493
Explanation: it’s above the previous
Do a essay about engineering
Take a look around yourself. What do you see? Maybe books, chairs, a television, or even your clothes. All the day to day things that are man-made, you can be sure that an engineer helped make it. Engineers have shaped our world as we know it. There are many different kinds of engineers from chemical, mechanical, textile, civil, agricultural and structural engineers. Our civilization would be as advanced as the Stone Age without these people. This career demands a wide education of math and science. It is an ever-changing career with new advances in materials and the way products are produced. Engineering careers are very secure with respect to compensation. Regardless of this, it does have it’s disadvantages…show more content…
(Britannica 243) Another disadvantage of being an engineer is the actual status of being one. It is not looked upon as highly as other fields such as doctors and lawyers. Most of the time they are looked upon as nerds. In addition, most engineers are not promoted to high level positions such as presidents or top executives. They do not have the accounting or business education to do that particular job. This means that most engineers never get the opportunity to be their own boss. (Basta 22)
The job of an engineer itself is a creative job. The actual definition of an engineer is “The profession in which a knowledge of the mathematical and natural sciences gained by study, experience and practice is applied with judgment to develop ways to utilize the materials and forces of nature economically for the benefit of mankind.” (Bastas 24) In having the basic skills and experiences in math and science, an engineer is basically an inventor. They are given a problem and are depended on to come up with a solution. Whether it be a new chemical, a mechanical part, or even a whole new system such as computer operating program, engineers are the problem solvers of our materialistic society.
There are four major types of essay and they are the Descriptive, Argumentative, Expository and the Narrative essay.
What is an essay?An essay is generally are a piece of writing that gives an argument, educates or entertains a reader about a specific topic.
Writing an essay about engineering is to educate people about the field of study, and therefore, falls under the Expository essay.
Therefore, below are some tips that will guide you in writing an expository essay:
Start the essay structure with a good introduction.Write down a brief outline and craft out a summary of discussion topics to support your idea.Choose the point of view used in writing carefully.Use a clear concise language to write. Do NOT use figurative language.State your argument. Clarify your main point.Capture the reader's attention with your appealing introduction.Use your strong ideas and focus on them on each paragraph.Connect sentences with clear and logical main idea.Include your supporting information and cite your sources.Summarize your points/arguments with a concise and clear conclusion.Read more about essay here:
https://brainly.com/question/25607827
NO SCAMS
The Air Force is F 22 raptor fighter jets mass is 21,000 KG the F 22 is flying at a height of 26,000 miles what is its gravitational potential energyThe Air Force is F 22 raptor fighter jets mass is 21,000 KG the F 22 is flying at a height of 26,000 miles what is its gravitational potential energyThe Air Force is F 22 raptor fighter jets mass is 21,000 KG the F 22 is flying at a height of 26,000 miles what is its gravitational potential energyThe Air Force is F 22 raptor fighter jets mass is 21,000 KG the F 22 is flying at a height of 26,000 miles what is its gravitational potential energy
Answer:
2758.09
Explanation:
Which of the following maintenance items helps to ensure the vehicles engine lasts as long as possible?
A) cabin air filter
B) tire rotation
C) oil change
D) all of the above
Answer:
c
because oil is preventing corrosion and rust
If the actual work is 0.85 MJ for a compressor, and the isentropic compressor work is 0.8 MJ, what is the isentropic compressor efficiency
Answer:0.94
Explanation:
nc=(wc,isentropic)/(wc,act)
A change in what component of microscopy influences the apparent size of the objects being viewed?.
Magnification is known to often influence the size of an object under the microscope. A change in what component of microscopy influences the apparent size of the objects being viewed is called magnification.
An Increased magnification will lead to an increase the apparent size of the object. Magnification is simply known to be the process of making bigger the apparent size of something.Magnifying glasses is also known to make objects looks bigger due to their convex lenses. The magnification can be said to be positive or negative in its work.
Learn more about magnification from
https://brainly.com/question/15744335
direction: fill in the blanks you can find your answer in the box provided below write your answer in blank provided.
1. Never wear open toed ______ while working with hot metal or welding apparatus.
2. The ______ must make a perfect seal around the ear to be effective
3. the ______ must be kept free of abrasions scrapes and nicks.
4. an apparatus worn over the mouth and nose to prevent inhalation of dust is ______.
5. when grinding and cutting _______ should be used.
6. the _______ makes you work with one hand only.
7. you should wear _______ to protect the feet from falling or rolling object.
8. the ______ prevent the entry of sparks between our clothes and body.
9. the ______ must be worn while inside the workshop.
10. the ______ is more convenient to use because it allows both hands to work freely.
Answer:
1) footwear (100% sure)
2) earmuffs (100% sure)
3) welding helmet
4) respirator (100% sure)
5) safety glasses
6) hand held shield (100% sure)
7) safety shoes (100% sure)
8) leather jacket
9) hard hat (100% sure)
10) safety harness (100% sure)
How do you earn Brainliest?
How should you mark a component listed on the VCU form that
is not installed on the customer's vehicle?
A) Mark it N/A
B) Nothing
C) Mark it green
D) Mark it red
Question 2 (1 point)
Technician A says Radial ply Tires are used for carrying a heavy Load. Technician B says that Bias Ply Tires are made with the Plies laid diagnally.Which Technician is correct?
a)Technician A
b)Technician B
c)Both A & B
d)Neither
Answer:
c)
Explanation:
they are both correct because ply tires can carry and are made with the plies laid diagonally.
some roadways are tilted as they go around a turn. what is the purpose of this tilt?
Answer:
So no one hits each other
Explanation:
If they dont turn or stop everyone will crash
Which principle of the software engineering code of ethics has gilbert violated?.
Answer:
Judgement
Explanation:
Gilbert is required by the Judgement Principle to "disclose those conflicts of interest that cannot reasonably be avoided or escaped." Since Gilbert professionally believes that the software meets specifications, secures documents, and satisfies user requirements, it is not clear if he violated any principle. However, he could have informed his client of his interest in the software and also presented other software packages of different companies from which the client could make its independent choice.
What happens when you put diesel in a gas engine.
Explanation:Since diesel fuel is thicker and denser than gasoline, the fuel pump will struggle to move the diesel/gasoline mixture through the system. Instead, it will clog up the fuel filter. And whatever amount of diesel that then makes its way to the engine will clog the fuel injectors, making them inoperable.
You are given a rectangular piece of cloth with dimensions X by Y, where X and Y are positive integers, and a list of n products that can be made using the cloth. For each product i in [1,n] you know that a rectangle of cloth of dimensions ai by bi is needed and that the final selling price of the product is ci. Assume that ai, bi, and ci are all positive integers. You have a machine that can cut any rectangular piece of cloth into two pieces either horizontally or vertically. Design an algorithm that finds the best strategy for cutting an X by Y piece of cloth so that the products made from the resulting pieces give the maximum sum of selling prices. You are free to make as many copies of a given product as you wish, or none if desired. How can i prove that the recursion is exponential and that dynamic programming is polynomial
The proof that recursion is exponential and that dynamic programming is polynomial is given by the formula;
P(x,y) = max{
P(x,y)
max (1 <= h <= X) { P[h, Y] + P(X - h, Y) }
max (1 <= v <= Y) { P[X, v] + P[X, Y - v] }
}
To prove that the recursion is exponential and that dynamic programming is polynomial. we will do so as follows;
Let us first have the assumption that the cloth is in such a manner that either way, a product can be oriented. This implies that that after a cut, we will now have two pieces of cloth.
Now, we will make a list of the side lengths of the products that can fit in the piece after which we will consider a vertical cut for each of the side length as well as a horizontal cut for each of the side length, then we apply the same algorithm to each of the two resulting pieces.
Thus, after the point above, it is likely true that in some instances, there may be a place to cut that is not at a product side length. However, It might be better for us to make a list of lengths composed of one or more pieces side by side as long as the sum is less than the length of the side being considered.
Lastly, we would note that this recursive approach is not limited to just two -dimensional problems as It could also be applied to a single or more than two dimensions. A useful proof would be to prove it for one dimension, then assuming it is true for n dimensions, prove it is true for n + 1 dimensions.
Thus;
P(x,y) = max{
P(x,y)
max (1 <= h <= X) { P[h, Y] + P(X - h, Y) }
max (1 <= v <= Y) { P[X, v] + P[X, Y - v] }
}
Read more at; https://brainly.com/question/11665190
People in accounting record, classify, summarize, analyze, and communicate a business's financial information for use in management decision-making.
Question 1 options:
True
False
Answer:
TRUE
Explanation:
hello nezuko its me bakugo
water 1°C.
12. Force is measured in
in the SI metric system.
Answer:
because metric units are decimal based they are easily converted by moving decimal points
Dislocations have a major effect on the plastic deformation of metals, but do not play a major role in the mechanical behaviour of ceramics. Why?.
Dislocation often plays a major role in plastic deformation of the material because material can be increased by plastic deformation. The number of dislocation often brings about motion depicts plastic deformation.
Dislocations are gotten and move when a stress is applied. The motion of dislocations allows slip and then plastic deformation takes place.
The dislocations often move along the densest planes of atoms in a material. This is due to the fact that the stress needed to shift the dislocation rises with the spacing between the planes.
Dislocations play an essential role in the plastic deformations of crystalline materials as they hinder the synchronized breakage of bonds between atoms in materials.
Learn more from
https://brainly.com/question/15261205