The total thermal resistance of the wall can be found by summing the thermal resistances of each section:
= 4.277 m^2.K/W
To determine the rate of heat transfer through the wall, we can use Fourier's law of heat conduction which states that the rate of heat transfer through a material is proportional to the temperature gradient across the material, and can be expressed as:
q = -kA * dT/dx
where q is the rate of heat transfer, kA is the thermal conductivity of the material, dT/dx is the temperature gradient, and the negative sign indicates that heat flows from higher temperatures to lower temperatures.
(a) To find the rate of heat transfer through the wall, we need to first determine the thermal resistance of each section of the wall. The thermal resistance is given by:
R = L / k
where R is the thermal resistance, L is the length of the material, and k is the thermal conductivity.
Using this equation, we can find the thermal resistance of each section as follows:
[tex]R_A = 5 / 2 = 2.5 m^2.K/W[/tex]
[tex]R_B = 0.22 / 35 = 0.0063 m^2.K/W[/tex]
[tex]R_C = 5 / 20 = 0.25 m^2.K/W[/tex]
[tex]R_D = 0.22 / 15 = 0.0147 m^2.K/W[/tex]
[tex]R_E = 0.22 / 35 = 0.0063 m^2.K/W[/tex]
[tex]R_F = 3 / 2 = 1.5 m^2.K/W[/tex]
(b) To find the temperature at the point where sections B, D, and E meet, we can assume that there is no heat generation within the wall (i.e., steady-state conditions), so the temperature at any point within the wall is the same in the x-direction. Therefore, we can use the thermal resistance network to find the temperature drop across each section:
ΔT_A = (300 - 100) = 200°C
Learn more about temperature here:
https://brainly.com/question/11464844
#SPJ4
Consider a quantum channel of a single qubit. This can be represented as a map between the Bloch sphere polarization vectors before the operation (Þ) and after the operation (P) P = (). P+c, where () is a 3 x 3 real matrix, and č is a constant vector. Suppose we would like to learn the properties of this channel, i.c. () and c, by feeding it many pre-prepared qubits and measure the outcomes. In particular, suppose we can measure the polarization vectors P accurately. 1. Supposc wc prepare a set of qubits in state (0) and let them go through the channel. What can we learn about O and after measuring the resulting P'? 2. Design a set of measurements (for example, starting qubits with different initial states) so that we can measure O and i completely.
A specific set of initial states that can be used for this purpose is the set of three Pauli matrices: |0⟩, |1⟩, |+⟩ = (|0⟩ + |1⟩)/√2, and |−⟩ = (|0⟩ − |1⟩)/√2.
By measuring the resulting polarization vectors for each of these four initial states, we can construct a set of four linear equations that can be used to solve for the unknowns completely.
We can then use these measurements:
[tex]P = ()P + č[/tex]
where P is a column vector containing the measured polarization vectors, () is the 3 x 3 real matrix representing the channel, and č is the constant vector. By measuring the resulting polarization vectors for each initial state, we can construct a set of linear equations of form:
[tex]P_i = ()P_i + č[/tex]
To Know more about linear equation , here
https://brainly.com/question/11897796
#SPJ4
In the figure below, a planet orbits the sun. During which of the three sections will the planet have the lowest average velocity?
a) B
b) A
c) the information given is insufficient to answer the question
d) C
e) the average velocity is the same for sections A, B, and C
Based on the image given, the section where the planet will have the lowest average velocity is C since it is at the greatest distance from the Sun.
The correct option is D
What is Keplers's second law of planetary orbits?Kepler's Second Law states that as a planet orbits the Sun, an imaginary line connecting them sweeps across the same amount of space at the same rate.
This means that planets do not travel along their orbits at a constant speed, rather, they move at varying speeds so that the line connecting the centers of the Sun and the planet covers the same amount of ground in the same amount of time.
Perihelion refers to the planet's point of closest approach to the Sun while the point of greatest separation is aphelion.
A planet moves fastest at perihelion and slowest at aphelion.
Learn more about Kepler's second law at:
#SPJ1
The ice and steam point on a thermometer are found to be 96mm apart . What is the length of mercury thread above ice point when the true temperature reads 58°c
112mm is the length of mercury thread above ice point when the true temperature reads 58°C.
What is mercury?Mercury has the chemical symbol Hg and the atomic number 80. It was once known as hydrargyrum, derived from the Greek words hydor (water) as well as argyros (silver) (silver).
Mercury exists as the only lustrous metal known to be liquid at ordinary temperature and pressure. It is a hefty, silvery d-block element.
For difference of 100 degree Celsius = (96–2)= 94 mm length of mercury column
For difference of 75 degree Celsius = 94×58/100 = 18 mm length of mercury column
Total length of mercury column at 75 degree Celsius = 18+94=112 mm
Therefore, 112mm is the length of mercury thread above ice point when the true temperature reads 58°C.
To learn more about mercury, here:
https://brainly.com/question/25956102
#SPJ9
When an aluminum bar is temporarily connected between a hot reservoir at 690 K and a cold reservoir at 258 K, 2.60 kJ of energy is transferred by heat from the hot reservoir to the cold reservoir.
(a) In this irreversible process, calculate the change in entropy of the hot reservoir. _______ J/K (b) In this irreversible process, calculate the change in entropy of the cold reservoir. _______ J/K (c) In this irreversible process, calculate the change in entropy of the Universe, neglecting any change in entropy of the aluminum rod. _______ J/K (d) Mathematically, why did the result for the Universe in part (c) have to be positive?
Based on Energy a) ΔS = -3.77 J/K b) ΔS = 10.08 J/K c) ΔS_cold = 6.31 J/K d) change in entropy of the Universe has to be positive
Based on Energy :
(a) To calculate the change in entropy of the hot reservoir, we can use the equation ΔS = Q/T, where ΔS is the change in entropy, Q is the amount of heat transferred, and T is the temperature in Kelvin. So, ΔS = -2.60 kJ / 690 K = -3.77 J/K.
(b) Using the same equation, we can calculate the change in entropy of the cold reservoir: ΔS = 2.60 kJ / 258 K = 10.08 J/K.
(c) To calculate the change in entropy of the Universe, we can add the changes in entropy of the hot and cold reservoirs: ΔS_univ = ΔS_hot + ΔS_cold = -3.77 J/K + 10.08 J/K = 6.31 J/K.
(d) The change in entropy of the Universe has to be positive in an irreversible process because the total entropy of the system and its surroundings always increases. The Second Law of Thermodynamics states that any process that occurs spontaneously (i.e. without external intervention) will always result in an overall increase in entropy. In this case, the heat transfer from the hot reservoir to the cold reservoir is an irreversible process, which means that the overall change in entropy of the Universe must be positive. If the change in entropy of the Universe were negative, it would imply that the process is reversible, which is not the case for an irreversible process. Therefore, the positive value for ΔS_univ in part (c) confirms that the process is irreversible.
Learn more about energy here:
https://brainly.com/question/1932868
#SPJ4
a scientist would like to investigate the effect of salt in irrigation water on the number of leaves found on their plants. they set up the following experiment:
The dependent variable in this experiment is the number of plants that can live in the water.
In an experiment, the dependent variable is the variable that is being measured or observed. It is the outcome variable that is affected by changes in the independent variable. In this case, the scientist is trying to determine how the amount of salt in the water affects the number of plants that can survive in the water.
Therefore, the number of plants is the variable that is being measured or observed, and it is the dependent variable in this experiment. The independent variable, in this case, would be the amount of salt in the water, which is being manipulated by the scientist.
To know more about the independent variable, here
brainly.com/question/28605199
#SPJ4
--The complete question is, A scientist conducted an experiment to determine how the amount of salt in a body of water affects the number of plants that can live in the water. In this experiment the dependent variable is--
A Spherical cloud of charge or radius R contains a total charge +Q with a nonuniform charge density that varies according to:
p(r)=p0Image for A Spherical cloud of charge or radius R contains a total charge +Q with a nonuniform charge density that variefor r<_ R
and p=0 for r>R1-r/R
Where r is the distance from the center of the cloud
Express all algebraic answers in terms of Q,R,r and fundamental constants,
(C) Derive an expression for p0
The expression for the charge density of a spherical cloud of charge of radius R and total charge +Q is given by:
p(r) = p0 for 0 ≤ r ≤ R
p(r) = 0 for r > R
Where p0 is the charge density at the center of the cloud, r is the distance from the center of the cloud, and C is a fundamental constant.
To derive an expression for p0, we can use Gauss' law to calculate the total charge within a sphere of radius r. Since the charge distribution is spherically symmetric, the electric field at any point outside the sphere is zero. Thus,
∫E·dA = Q/ε0
Where the integral is taken over a sphere of radius r, and ε0 is the permittivity of free space.
Using the divergence theorem, we can equate this to an integral of the charge density over the same sphere:
∫E·dA = ∫∇·p dV
Substituting in the expression for the charge density, we get:
Q/ε0 = ∫p0 (4πr2) dr
Integrating both sides and solving for p0, we get:
p0 = Q/(4πε0R3)
Learn more about Spherical cloud of charge or radius R:
https://brainly.com/question/14759319
#SPJ4
Which statement(s) below is(are) correct for the focal point of a converging lens? (Select all that apply.) A) A light ray entering parallel to the optical axis passes through the focal point on the other side of the lens B) All light rays going through through the focal point on the other side of the lens. C) A light ray passing through the focal point as it enters the lens goes through the focal point on the other side of the lens. D) A light ray passing through the focal point as it enters the lens exits the lens parallel to the optical axis
The correct statements for the focal point of a converging lens are:
A) A light ray entering parallel to the optical axis passes through the focal point on the other side of the lens.
C) A light ray passing through the focal point as it enters the lens goes through the focal point on the other side of the lens.
D) A light ray passing through the focal point as it enters the lens and exits the lens parallel to the optical axis.
What is a converging lens?A converging lens is a particular kind of lens that bends light in such a way that parallel light rays unite at a single focal point. Light bends towards the center of the lens because of its shape, which has a thicker center and a thinner edge. A distinct image is created at the focal point, which is where all of the refracted light converges. Common applications for this kind of lens include magnifying glasses, cameras, telescopes, and other optical equipment. Converging lenses—also known as convex lenses—may produce sharp, enlarged pictures because they can combine light. Converging lenses can be recognized by their form; they have a center that is rather thick.
To know more about a converging lens, check out:
https://brainly.com/question/29771989
#SPJ4
QUESTION 1
Which feature is most likely the result of erosion from a river passing through the area?
QUESTION 2
Which feature is most likely the result of a magma deposit melting into the strata from below?
QUESTION 3
Which feature is most likely the result of uplift due to faulting along a tectonic plate boundary?
QUESTION 6
Considering this diagram, explain why fossils are often found close to bodies of water.
1) Feature III is most likely the result of erosion from a river passing through the area.
2) Feature II is most likely the result of a magma deposit melting into the strata from below.
What is erosion?Erosion is the result of surface processes that move soil, rock, or dissolved material from one area of the Earth's crust to another, where it is deposited. Weathering, which involves no movement, is distinct from erosion.
3) Feature II is most likely the result of uplift due to faulting along a tectonic plate boundary.
6) Because water performs two functions that are crucial for fossils. The oxygen that would otherwise deteriorate them and cause them to decay or be consumed by organisms larger than bacteria is primarily blocked by the sediment that it carries to fill in the area around them.
The oxygen is completely blocked out as the sediments fill in further, and this causes the sediments to compact. The minerals in the water and sediments may then eventually migrate into the fossils due to pressure, heat, and primarily time.
This heavily depends on the passage of time because it is a very slow process, the quantity of minerals present because of the sediments' makeup, and the history of pressure and heat because that affects the mobility of the minerals.
Learn more about erosion
https://brainly.com/question/30587260
#SPJ1
A 1.0-cm-diameter microscope objective has a focal length of 2.8 mm. It is used with light of wavelength of 550 nm.
Part A
What is the objective's resolving power if used in air?
Express your answer with the appropriate units.
Part B
What is the resolving power of the objective if it is used in an oil-immersion microscope with n(oil)= 1.45?
Express your answer with the appropriate units.
Objective resolving power if used in air is 661 nm/cm , the resolving power of the objective if it is used in an oil-immersion microscope is = 963 nm/cm
The ability of an optical instrument, such as a microscope or telescope, to differentiate and separate two objects that are close together is known as its resolution power.
Part A :
Resolving power = 1.22λ/D
= 1.22(550 nm)/(1.0 cm)
= 661 nm/cm
Part B :
Resolving power = 1.22λn(oil)/D
= 1.22(550 nm)(1.45)/(1.0 cm)
= 963 nm/cm
What exactly is resolve power?
It is established by comparing the instrument's aperture diameter to the wavelength of light utilized. The instrument's ability to differentiate between two close objects improves with increasing resolving power. A telescope's lens or mirrors focus light on a single point as it travels through them. The telescope's resolving power is based on how close the two points can be to each other before they are impossible to tell apart. More distant stars, galaxies, and other celestial objects can be seen in the image with a higher resolving power. In order to comprehend the universe and conduct scientific research, resolve power is absolutely necessary.
Learn more about Resolving power:
brainly.com/question/30432649
#SPJ1
At one instant an object in free fall is moving downward at 50 meters per second. One second later its speed is about Select one: a. none of these b. 60 m/s c. 25 m/s d. 100 m/s e. 50 m/s
The final velocity of the of the object is 60 m/s.
What is is speed?Velocity is the rate of change of displacement.
To calculate the speed of the object, we use the formula below
Formula:
v = u+gt.................. Equation 1Where:
v = Final velocityu = Initial velocity = 50 m/sg = Acceleration due to gravity = 10 m/s²t = Time = 1 sSubstitute these values into equation 1
v = 50+(10×1)v = 50+10v = 60 m/sHence, the right option is b. 60 m/s.
Learn more about velocity here: https://brainly.com/question/24445340
#SPJ1
A juggler throws a bowling pin straight up with an initial speed of 8.80m/s . How much time elapses until the bowling pin returns to the juggler's hand?
The bowling pin will take 1.79 seconds to return to the juggler's hand.
Assuming no air resistance, we can use the kinematic equation for vertical motion:
Δy = [tex]vi*t + (1/2)at^2[/tex]
where Δy is the change in height, vi is the initial velocity, t is the time elapsed, a is the acceleration due to gravity (which is -9.81 m/s^2), and we can set the final height to be equal to the initial height, since the bowling pin returns to the juggler's hand.
Therefore, we can write:
[tex]0 = vi*t + (1/2)at^2[/tex]
Substituting in the given values, we get:
[tex]0 = (8.80 m/s)t + (1/2)(-9.81 m/s^2)*t^2[/tex]
Simplifying and solving for t, we get:
[tex]t = (2*8.80 m/s) / 9.81 m/s^2[/tex]
t = 1.79 seconds
Therefore, the bowling pin will take 1.79 seconds to return to the juggler's hand.
To know more about Initial velocity, here
brainly.com/question/9365999
#SPJ4
which of the following are possible explanations for the formation of the meteor crater? multiple select question. volcanic explosion a large pothole formed by swirling water action in an extremely large river large meteoroid collision
A significant meteoroid collision caused the meteor crater to develop. The right response is option c.
A meteor is a streak of light in the sky that results from a meteoroid colliding with Earth's atmosphere. Meteoroids are rock or iron clusters that orbit the sun.
Meteor Crater, located close to Winslow, Arizona, is one of the most well-known craters on Earth. A 50-meter (164-foot), 150,000-ton meteorite fell into the desert roughly 50,000 years ago, instantaneously creating the crater. The diameter and depth of Meteor Crater are 1.2 km (0.75 miles) and 175 m (575 feet), respectively.
To know more about the meteor crater, here
brainly.com/question/11185539
#SPJ4
--The complete question is, which of the following are possible explanations for the formation of the meteor crater?
a. volcanic explosion
b. a large pothole formed by swirling water action in an extremely large river
c. large meteoroid collision--
an object is moving on a circular path of radius pi meters at a constant speed of 4.0 m/s. the time required for one revolution is
The time required for one revolution is π²/2 seconds.
The time required for one revolution of an object moving on a circular path can be found by dividing the circumference of the circle by the speed of the object. One revolution typically refers to the complete circular movement of an object around another object or axis. The circumference of a circle is given by the formula
C = 2πr,
where r is the radius of the circle.
In this case, the radius of the circle is π meters, so the circumference is
C = 2π(π) = 2π
The speed of the object is 4.0 m/s, so the time required for one revolution is:
t = C/v
t = 2π²/4.0
t = π²/2.
To learn more about Time :
https://brainly.com/question/2364404
#SPJ11
Arrange the components by how much of the material in the universe they represent, with the largest fraction at the bottom.Instructions- all the matter in the planets-all the matter in the galaxies- dark matter- dark energy
Arrangement based on material in universe: Dark Energy, Dark Matter, All matter in galaxies, all matter in planets.
In terms of the amount of material they represent in the universe, the components can be arranged as follows:
Dark Energy: Dark energy is the most abundant component in the universe, comprising approximately 68% of the total energy density. Dark energy is a form of energy that is believed to be responsible for the observed accelerated expansion of the universe.Dark Matter: Dark matter is the second most abundant component in the universe, comprising approximately 27% of the total energy density. Dark matter is a form of matter that does not interact with electromagnetic radiation, and is believed to be responsible for the gravitational effects that are observed in galaxies and clusters of galaxies.All the matter in the galaxies: The matter in galaxies, including stars, planets, gas, and dust, comprises a relatively small fraction of the total energy density in the universe, accounting for approximately 5% of the total.All the matter in the planets: The matter in planets is a very small fraction of the total energy density in the universe, accounting for a tiny fraction of a percent.Learn more about universe here:
https://brainly.com/question/11987268
#SPJ4
the boom oa carries a load p and is supported by two cables as shown. knowing that the tension in cable ab is 232 lb and that the resultant of the load p and of the forces exerted at a by the two cables must be directed along oa, determine the tension in cable ac.
To solve this problem, we need to use the principle of equilibrium. The sum of all the forces acting on the boom in the horizontal and vertical directions must be equal to zero. The tension in cable AC is approximately 685.9 lb.
Let's start by resolving the forces in the vertical direction. The weight of the boom and the load is balanced by the vertical components of the tensions in cables AB and AC, which are equal to each other. Therefore:
232 + TAC sin(45) = P + 1000
where TAC is the tension in cable AC.
Next, we can resolve the forces in the horizontal direction. The horizontal component of the tension in cable AB is balanced by the horizontal component of the tension in cable AC. Therefore:
TAB cos(30) = TAC cos(45)
We are given the tension in cable AB, so we can solve for TAC:
TAC = TAB cos(30) / cos(45)
Substituting this expression into the first equation, we can solve for TAC:
232 + TAB cos(30) / cos(45)sin(45) = P + 1000
TAC ≈ 685.9 lb
Therefore, the tension in cable AC is approximately 685.9 lb.
In this problem, we have a boom or beam OA carrying a load P and being supported by two cables AB and AC. The tension in cable AB is given as 232 lb, and we are asked to determine the tension in cable AC.
To solve the problem, we can start by drawing a free-body diagram of the boom and cables. The weight of the load P acts downward, while the tensions in cables AB and AC act upward at angles θ1 and θ2 with respect to the horizontal. We can also draw a horizontal line representing the direction of the resultant force acting along the beam OA.
Learn more about equilibrium here:
https://brainly.com/question/11920396
#SPJ4
Place in chronological order the following steps in the formation and evolution of Earth's atmosphere: Correct Answer List Question List (6 items) (Drag and drop into the appropriate area) Life releases CO2 from the subsurface into the atmosphere. Oxygen enables the growth of new life-forms. No more items Hydrogen and helium are captured from the protoplanetary disk. Volcanoes, comets, and asteroids increase the inventory of volatile matter. Hydrogen and helium are lost from the atmosphere. Plant life converts CO2 to oxygen.
Earth had essentially no atmosphere when it originated around 4.6 billion year ago out of a volatile mixture of gases and minerals. The ground had melted on it. An atmosphere developed while Earth cooled, primarily from gases emitted by volcanoes.
What elements make up the atmosphere on Earth?Approximately 78% of the gas in Upper orbit is nitrogen, while 21% is oxygen. In trace proportions, additional gases like carbon dioxide, neon, & hydrogen are also present in air.
What is significant about the atmosphere of Earth?In addition to providing us with the oxygenation we need to survive, it shields us from dangerous UV solar radiation. Without it, the pressure needed for liquid water to exist on the surface of our planet would not be possible. And it warm our globe, maintaining habitable temperatures.
To know more about Earth's visit:
https://brainly.com/question/3468253
#SPJ1
To releases it from rest, as shown. Comparing e measured e to expected value A student uses a heavy ball attached to a rope as a pendulum in an experiment. The ball is hanging so the rope is vertical. The student pulls the that the ball is moving slower than expected. Which of the following may account for the slower-than-expected speed? A. The student measured the mass of the ball to be higher than it actually is. B. The student did not account for the mass of the rope. С. The angle of the swing was so high that air resistance had a significant effect. D. The ball was accidentally given a small push when it was released. E. The student did not account for the stretch of the rope caused by the weight of the ball.
The reason that for account for the slower-than-expected speed is the student did not account for the stretch of the rope caused by the weight of the ball. The correct option is e.
The speed of ball is slower than expected speed due to stretch in length of string. The swing rate of the pendulum is determined by its length. The longer the pendulum, whether it is a string, metal rod or wire, the slower the pendulum swings.
Mass of rope or ball does not effect speed, time period or frequency.
Frequency is the number of occurrences of a repeating event per unit time. For clarity, also called temporal frequency, which is different from angular frequency.
To know more about the frequency, here
brainly.com/question/254161
#SPJ4
the reaction of automobile exhaust and ultraviolet light question 61 options: produces industrial smog. is affecting the stratospheric ozone concentration. produces photochemical smog. forms smoke and fog.
Photochemical smog is produced. Nitrogen oxides (NOx) and volatile organic compounds (VOCs) from vehicle exhaust combine with sunlight to create photochemical smog.
What results from the reaction of sunlight and exhaust from vehicles?When sunlight interacts with nitrogen oxides and at least one volatile organic compound (VOC) in the atmosphere, photochemical smog is created. Automobile exhaust, coal-fired power plants, and industrial pollutants all produce nitrogen oxides.
What causes photochemical smog?When nitrogen oxides and volatile organic compounds (VOCs) combine with sunlight, a mixture of pollutants called photochemical smog is produced, which explains why there is a brown cloud above cities. Due to the fact that we receive the most sunshine in the summer, it tends to happen more frequently.
to know more about photochemical smog here;
brainly.com/question/27960448
#SPJ1
a. derive the equation for the velocity vector as a function of time for the ball. assume that the ball is initially moving in the positive x-direction and positive y-directions.
To derive the equation for the velocity vector as a function of time for the ball, we need to know the acceleration vector as a function of time. Once we have the acceleration, we can integrate it with respect to time to obtain the velocity.
Assuming that the ball is moving in a two-dimensional plane (i.e., the x-y plane), the acceleration vector can be expressed as:
a = ax(t) i + ay(t) j
where, i and j are unit vectors in the x and y directions, respectively. We can determine the expressions for ax(t) and ay(t) by applying Newton's second law of motion:
F = ma
Where, F is the net force acting on the ball, m is the mass of the ball, and a is its acceleration.
Let's assume that the ball experiences a net force of F = Fx i + Fy j, where Fx and Fy are the x and y components of the force, respectively. Then we can write:
F = Fx i + Fy j = ma
Equating the x and y components, we get:
Fx = m*ax
Fy = m*ay
Solving for ax and ay, we get:
ax = Fx/m
ay = Fy/m
Now we can integrate ax(t) and ay(t) with respect to time to obtain the expressions for the velocity components:
v_x(t) = v_{0x} + ∫ ax(t) dt
v_y(t) = v_{0y} + ∫ ay(t) dt
where v_{0x} and v_{0y} are the initial velocities in the x and y directions, respectively.
If we know the expressions for Fx and Fy as functions of time, we can substitute them into the above equations to obtain the velocity vector as a function of time for the ball.
Learn more about velocity vector here brainly.com/question/13492374
#SPJ4
charge q2 is 2.5 x 10^-9 c and charge q1 has mass 0.2 g. the separation r is 5 cm, and the angle is 15 degree. find q1
The magnitude of the charge of the particle Q₁ is found to be 2.36 x 10⁻⁶ C.
The magnitude of charge Q₁ is 2.5 x 10⁻⁹ and the charge Q₂ is 0.2g and the separation between them is 5cm while the angle of attraction being degrees.
Now, we can write,
If the force of attraction due to charge is F and the weight of the body is W.
Fcos(90-15) = W
KQ₁Q₂/R²cos(75) = Mg
Where,
K is the constant,
Q₁ and Q₂ are charges,
R is the separation in them,
M is the mass of Q₁,
G is the gravitational acceleration.
Putting values,
9x10⁹x2.5 x 10⁻⁹x0.92Q₁/(0.05)² = 0.2/1000 x 9.8
Q₁ = 2.36 x 10⁻⁶ C.
So, the charge of Q₁ is 2.36 x 10⁻⁶ C.
To know more about electrostatic force, visit,
https://brainly.com/question/20797960#:~:text=Expert%2DVerified%20Answer&text=The%20electrostatic%20force%20between%20two%20charged%20objects%20is%20directly%20proportional,distance%20between%20the%20two%20objects.
#SPJ4
the magnitude of the normal acceleration is proportional to radius of curvature. inversely proportional to radius of curvature. inversely proportional to diamter of curvature. zero when velocity is constant.
The normal acceleration of a body travelling in a curved path is defined as the rate of change of its velocity vector. It is equal to the sum of the centripetal and tangential accelerations.
The magnitude of the normal acceleration is directly proportional to the radius of curvature, i.e a smaller radius of curvature implies a larger normal acceleration. Mathematically, the normal acceleration can be expressed as follows:
Normal acceleration = (v^2/r)
where v is the velocity of the body and r is the radius of the curvature. As the radius of the curvature decreases, the normal acceleration increases. Hence, the magnitude of the normal acceleration is directly proportional to the radius of curvature. On the other hand, it is inversely proportional to the diameter of curvature. The normal acceleration is also zero when the velocity of the body is constant. This happens when the body is travelling along a straight path. In such cases, the normal acceleration is zero since there is no change in the velocity vector in the direction perpendicular to the path.
To learn more about acceleration
brainly.com/question/12550364
#SPJ4
The correct solution to this question is that the magnitude of the normal acceleration is inversely proportional to the radius of curvature.
The curvature's reciprocal, R, is the radius of curvature in differential geometry. It is equal to the radius of the circular arc that, at that moment, most closely resembles the curve for a curve. The radius of curvature for surfaces is the diameter of a circle that fits a normal section or any combination of them the best.
The approximate radius of a circle at any given location or the curvature's vector length are both considered to be the radius of curvature of a curve. For any curve with the equation y = f(x), where x is a parameter, it exists.
Learn more about radius of curvature here brainly.com/question/30106465
#SPJ4
A particle moves along the x-axis. Its position varies with time according to the expression x = -4t + 2t2, where x is in meters and t is in seconds. Calculate the instantaneous velocity of the particle at t = 2.8 s.
The position -time relation from the graph is given x = - 4t + 2t². Then , at t = 2.8 s, x have the value of 4.48 m. Therefore, the velocity being 1.6 m/s.
What is velocity ?Velocity of an object is the measure of distance travelled per unit time. It is a vector quantity having both magnitude and direction. The magnitude of velocity is called speed of the object.
The instantaneous velocity of an object is its velocity at a particular instant of time.
Given the position- time relation of an object.
x = - 4t + 2t²
then at t = 2.8 s
x = 4 × 2.8 s + 2 ×(2.8 s)² = 4.48 m.
Then,
velocity = distance travelled / time
v = 4.48 m/2.8 s = 1.6 m/s.
Therefore, the instantaneous velocity of the particle is 1.6 m/s at t = 2.8 s.
Find more on instantaneous velocity:
https://brainly.com/question/13190516
#SPJ9
Consider the following statements (A) and (B) and identify the correct answer given below :
Statement A: Positive values of packing fraction implies a large value of binding energy
Statement B: The difference between the mass of the nucleus and the mass number of the nucleus is called the packing fractiona. A and B are correctb. A and B are false c. A is true, B is falsed. A is false B is true
Option (d) A is false, B is true. Statement A is false and statement B is true. The relationship between the packing fraction and the binding energy is more complex and depends on the details of the nuclear interactions.
Statement B is true. The packing fraction is defined as the difference between the mass of the nucleus and the mass number of the nucleus divided by the mass number. It is a measure of the binding energy per nucleon in the nucleus.
However, statement A is false. The packing fraction is related to the binding energy per nucleon, but a larger packing fraction does not necessarily imply a larger binding energy. In fact, a lower packing fraction (i.e., a less tightly bound nucleus) can sometimes have a larger binding energy per nucleon than a nucleus with a higher packing fraction. The relationship between the packing fraction and the binding energy is more complex and depends on the details of the nuclear interactions.
Learn more about nucleus here: brainly.com/question/23366064
#SPJ4
a solid conducting sphere (or a disk in two dimensions) is charged positively. describe what the distribution of these charges is after they come to equilibrium. drawing a picture would be helpful.
When a solid conducting sphere (or a disk in two dimensions) is charged positively, the positive charges are free to move within the sphere and distribute themselves evenly throughout the surface. This results in a uniform positive charge density on the surface of the sphere
what is conducting sphere?conducting sphere will have the complete charge on its outside surface and the electric field intensity inside the conducting sphere will be zero. For a spherical charged Shell the entire charge will reside on outer surface and again there will be no field anywhere inside it.
what is charge and it's types?charge is the physical property of matter that causes it to experience a force when placed in an electromagnetic field. Positive and negative electric charges are the two types of charges commonly carried by charge carriers, protons and electrons. Energy is created by the movement of charges.
Examples of the types of charges are subatomic particles or the particles of matter: Protons are positively charged. Electrons are negatively charged. Neutrons have zero charge
To know more about conducting sphere visit:
https://brainly.com/question/12444946
#SPJ4
i. indicate below which quantities should be graphed to yield a straight line whose slope could be used to calculate a numerical value for the charge to mass ratio of an electron.
The two quantities that should be graphed to yield a straight line whose slope could be used to calculate a numerical value for the charge to mass ratio of an electron are electric field strength and velocity.
What is velocity?Velocity is a vector quantity that describes the rate of change of an object's position in a given amount of time. It is typically measured in meters per second (m/s), but can also be measured in other units such as feet per second (ft/s) or kilometers per hour (km/h). It is a measure of both the speed and direction of an object's motion, and is distinct from speed, which is simply the rate of motion in a given direction. Velocity can be calculated by taking the derivative of an object's position with respect to time. It is an important concept in physics and is used to describe the motion of objects in a variety of situations. For example, in a car, velocity is used to determine the car's acceleration, and in an airplane, velocity is used to describe the airspeed.
To learn more about velocity
https://brainly.com/question/80295?source=archive
#SPJ1
How does gravity affect the movement of the planets around the sun, stars grouped in galaxies, and galaxies grouped in clusters?
Thoroughly explain your answer, making sure to include an example and describe how this force keeps planets in orbit. Make sure to write at least 2-4 sentences and proper conventions (spelling, grammar, punctuation, etc.) to respond. Put all answers in your own words. PLEASE ANSWER QUICKLY WORTH 50 POINTS
Gravity affect the movement of the planets around the sun, stars grouped in galaxies, and galaxies grouped in clusters by applying force.
What is gravitational force?Gravitational force is indeed a non-contact, constantly attracting force. This implies it may act at a distance that does not require the interacting items to be in contact with each other. When we examine gravity operating on a system, we can assume that the gravitational force acts immediately on the system's center of mass.
Gravity keeps things together. It is a force that attracts matter towards it. Anything with mass creates gravity, but the amount of gravity is proportional to the amount of mass. Therefore, Jupiter has a stronger gravitational pull than Mercury. Distance also affects the strength of the gravitational force.
Therefore, gravity affect the movement of the planets around the sun by applying force.
To know more about gravitational force, here:
https://brainly.com/question/6594264
#SPJ1
Applying the maximum force you can exert, the heaviest box you can push at constant speed across a level floor with coefficient of kinetic friction μ has weight w. Another box sits on a ramp that is inclined at an angle of β above the horizontal. The coefficient of kinetic friction between the box and the ramp is μ.
If you apply the same magnitude maximum force, now parallel to the ramp, that you applied to the box on the floor, what is the heaviest weight box that you can push up the ramp at constant speed? (In both cases assume you can give enough extra push to get the box started moving.) Express your answer in terms of quantities given in the problem.
The heaviest box that can be pushed up the ramp at constant speed is the same as the weight of the box that can be pushed across the level floor at constant speed with the same force, since the force applied is the same in both cases.
This is because the force of gravity is the same for both boxes, and the force of friction is equal to the force applied in both cases, so the net force up the ramp is the same as the net force across the floor. Therefore, the heaviest weight box that can be pushed up the ramp at constant speed with the same force is w.
What is net force?
Net force is the total amount of force acting on an object. It is the combination of all the individual forces acting on an object. It is calculated by adding the individual forces together.
To learn more about net force
Here: https://brainly.com/question/12970081
#SPJ1
earth's gravity attracts a person with a force of 120 lbs. the force with which the earth is attracted towards the person is
The force with which the Earth is attracted towards the person is equal to the same force of 120 lbs.
This is due to the law of universal gravitation. This law states that any two objects in the universe attract each other with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between them. Therefore, the Earth and the person both experience a force of 120 lbs due to their mutual attraction.
The law of universal gravitation states that any two objects in the universe attract each other with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between them. This means that the greater the mass of the objects and the closer they are to each other, the stronger the force of attraction will be. This law was first proposed by Isaac Newton in 1687 and is one of the most fundamental concepts in physics.
To know more about force please refer:
https://brainly.com/question/13191643
#SPJ4
Select the correct answer.
At which stage in Kohlberg's level of conventional morality does an individual realize the importance of maintaining law and order?
OA societal conformity
OB. social contract and individual rights
O C.
individualism and exchange
OD.
universal ethical principles
OE obedience and punishment
True or False: temperature in celsius is a ratio scale; zero degrees celsius does not represent a complete absence of heat.
The statement (temperature in celsius is a ratio scale; zero degrees celsius does not represent a complete absence of heat) is true.
The temperature in Celsius is not a ratio scale, as it does not have a true zero point that represents the complete absence of heat. The zero point of the Celsius scale is arbitrarily defined as the temperature at which water freezes at standard atmospheric pressure, but it does not indicate the complete absence of heat. Therefore, Celsius temperature is an interval scale, not a ratio scale.
The term "temperature" refers to a physical number that provides a quantitative expression of the qualitative concepts of warmth and chilliness. A thermometer is what is used to measure the temperature.
Want to know more about temperature visit the link which is given below;
https://brainly.com/question/7510619
#SPJ4