Answer:
A. Security
Explanation:
Mark Brainliest if it was correct :)
A cylinder power balance test is being performed on a vehicle with sequential port fuel injection. Two adjacent cylinders are under performing. Technician A says this could be caused by a restriction in the fuel injectors. Technician B says this could be caused by leaking secondary insulation. Who is correct
Answer:
Neither A nor B
Explanation:
A cylinder balance test is used to locate cylinders that are underperforming and leading to loss of power and unbalanced engine performance, by measuring the drop in RPM on each cylinder as compared to the other cylinders
The factors that result in under performing cylinders includes;
1) Problem with the ignition
2) Inadequate or restricted fuel delivery
3) Valve faults
4) Piston wear
Where adjacent cylinders are the cause for the lack of power, the likely causes includes;
1) Head gasket fault
2) Crack in the head
3) Crack in the block.
Three-dimensional measuring references all of these EXCEPT:
radius.
length.
width.
height.
Answer:
Radius. It is only used for Spheres
Explanation:
A disc brake rotor is being machined. Technician A says that a feed rate of 0.0008 inch per revolution and 150 RPM is where the rotor should be set for a final cut. Technician B says that the rotor should be given a non-directional surface finish using 150 grit sandpaper. Which technician is correct?
Answer:
Technician B only
Explanation:
During rotor reconditioning, which is the process also known as machining and sanding, where sanding is the involves the application of between 120 and 150 grit sandpaper while using a non-excessive force that is applied non-directionally for up to 60 seconds on each side such that the surface roughness meets OE standards. The rotors are then cleaned by washing after they are serviced before they can then be installed.
Technician A says that the brake pedal should be depressed with as much force as possible during the normal bleeding procedure. Technician B says that the brake pedal should be pumped rapidly during this manual bleeding procedure to force the air down toward the bleeder valve(s). Which technician is correct
Answer:
The appropriate answer is "Neither technician A nor B".
Explanation:
Two consultants or engineers complete the course of treatment A particularly unique upconverter to complement this same master cylinder. The customary static temperature would be used whenever the steering system has always been bleeding would be: 30 psi Two technicians start debating the bleeding atmosphere from either the hydraulic system.Therefore this obvious response is the appropriate one.
Let me help you with your baggage.
If eating three-egg omelets causes weight-gain, budgie eggs are a good substitute.
The waitress was not amused when he ordered green eggs and ham.
Peanut butter and jelly caused the elderly lady to think about her past.
It's not often you find a soggy banana on the street.
his seven-layer cake only had six layers.
I love bacon, beer, birds, and baboons.
We should play with legos at camp.
She did her best to help him.
His son quipped that power bars were nothing more than adult candy bars.
They improved dramatically once the lead singer left.
If you like tuna and tomato sauce- try combining the two. It’s really not as bad as it sounds.
Separation anxiety is what happens when you can't find your phone.
She tilted her head back and let whip cream stream into her mouth while taking a bath.
We have a lot of rain in June.
The father died during childbirth.
He set out for a short walk, but now all he could see were mangroves and water were for miles.
David subscribes to the "stuff your tent into the bag" strategy over nicely folding it.
You have every right to be angry, but that doesn't give you the right to be mean.
He decided water-skiing on a frozen lake wasn’t a good idea.
Answer:
is this free points??????????????????????????????
Explanation:
Help I will brainliest
Answer:
hacking?
Explanation:
jsd
Summarize the difference in hydraulic and pneumatic systems.
Answer:
The main difference between a pneumatic system and a hydraulic system lies in how the energy necessary to make these systems work is generated: thus, while in the pneumatic system this energy is generated through the compression of gases, in the hydraulic system the energy is obtained Through the insertion of pressurized fluids, such as water. Furthermore, hydraulic systems are closed circuits, where the water constantly circulates within the system; while in pneumatic systems the air that is compressed and used is constantly renewed.
Technician A says that the most commonly used combustion chamber types include hemispherical, and wedge. Technician B says that coolant and lubricating openings and passages are located throughout most cylinder heads. Which technician is correct
Answer:
Technician A and Technician B both are correct.
Explanation:
Technician A accurately notes that perhaps the forms of combustion process most widely used are hemispherical and cross.
Technician B also correctly notes that in several cylinder heads, cooling system and greases gaps and pathways are found.
An artist is creating a gigantic mobile using old cars. On one end of the mobile, a 2100 lb Plymoth is suspended 30 feet from the fulcrum. In order for the mobile to be balanced, where should the artist suspend a 1400 lb Volkswagon?
a
20 feet from the fulcrum
b
7 feet from the fulcrum
c
45 feet from the fulcrum
d
on the fulcrum
Answer:
c 45 feet from the fulcrum
Explanation:
The moment at the fulcrum must be the same for each car. If the distance is d, then the artist must have ...
(2100 lb)(30 ft) = (1400 lb)(d)
2100·30/1400 ft = d = 45 ft
The Volkswagen should be 45 ft from the fulcrum.
Answer:
C. 45 feet from the fulcrumThat artist should suspend a 1400 lb/pounds Volkswagen.how far away from the compressor unit should an air transformer be installed?
Answer:
During installation, the air transformer should be located at least 25 feet minimum from the compressor unit
Explanation:
An air transformer is used to remove the dirt, water and oil in the compressed air and to filter as well as to provide air regulation and are required in spray finishing tasks that calls for a regulated clean and dry supply of air
The air transformer measures the pressure of the regulated air and can also come with air outlets for air operated tools, blow guns, spray guns, as well as for other purposes
In order to operate efficiently, the air transformer are required to be installed at a minimum distance of 25 feet (7.6 m) from the compressor unit.
What is the value of the expression 8 cubed?
A. 24
B. 83
C. 512
D. 6,561
What differentiates an athletic trainer from a clinical exercise physiologist?
An athletic trainer must have clinical experience.
An athletic trainer must be certified to obtain clinical experience.
An athletic trainer is more likely to obtain a master’s degree.
An athletic trainer is more likely to work directly with physicians.
Answer:
It's number 3
Explanation:
An athletic trainer must have clinical experience.
Technician A says that valve stem height should be checked and the top of the valve ground, if necessary. Technician B says that an incorrect valve stem height may hold the valve open. Which technician is correct
Answer:
Technician A only
Explanation:
The valve stem height is important as the effects of incorrect valve stem height includes;
1) Side thrust
2) Highly recessed valve
3) Effect on the geometry of the combustion chamber
4) Changes in the volume of the combustion chamber
5) The amount of lifter preload
6) The spring height
7) The amount the valve lifts above the valve seat
8) The valve life span
The valve may stay open after the camshaft lobe is moves past the under the lifter when a valve float occurs at high engine speeds
The valve tips can be grinded as recommended by the manufacturer to correct the the valve stem height.
find the mass of electron
Answer:
9.10938356 × 10^-31 kilograms
Explanation:
i suck at chem lol
please tell us about your biggest success solving any mechanical issue
Explanation:
My biggest success solving any mechanical issue is learning how to use a wheelchair and making it easier for my sibling to move around.
Since my sibling broke her legs permanently, I felt terrible and wanted to do something to help out. My hallways were very small, so I wanted to make it easier for her to get around. I asked my parents if we could take down an unneeded wall in the hall, and so we did.
I calculated a bunch of thingies, and soon, my sibling could get around the house with ease, which really made me feel a lot better.
What is an actuator?
Answer:
An actuator is a component of a machine that is responsible for moving and controlling a mechanism or system, for example by opening a valve.
the worst time you have had with a mechanical issue
Answer:
When I was taking my sat exam online and my phone battery died
It took my poor dad three attempts to successfully have his truck fixed at the shop before they actually fixed anything.
Entering information on a device is called what?
A. input
B. output
C. programming
D. coding
Explanation:
I'm not an engineering expert, but if I had to guess, I'd say it's A: Input.
Which option identifies which design process should be used in the following scenario?
Jill is trying to create a new water cooling system inside a car. She needs to determine which components can have material changes for
the best cost benefit ratio.
Answer:
What are the answers, and which one is the second one, the order is randomized for each of the answers.
Explanation:
Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz
1. How is diesel fuel ignited in a warm diesel engine?
A. Glow plugs
B. Heat compression
C. Spark plugs
D. Distributor-less ignition system
2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
B. Common rail
C. Direct injection
D. Distributor injection
3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
B. High pressure common rail
C. Direct injection
D. Distributor injection
4. The three phases of diesel ignition include _______________________.
A. Glow plug ignition, fast burn, slow burn
B. Slow burn, fast burn, slow burn
C. Ignition delay, repaid combustion, controlled combustion
D. Glow plug ignition, ignition delay, controlled combustion
5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
A. Fuel filter
B. Fuel supply line
C. Fuel return line
D. Water-fuel separator
6. The diesel injection pump is usually driven by a _________________.
A. Gear off the camshaft
B. Belt off the crankshaft
C. Shaft drive off of the crankshaft
D. Chain drive off of the camshaft
7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
A. Distributor
B. Inline
C. High-pressure common rail
D. Rotary
8. Glow plugs should have high resistance when _____________and lower resistance when __________________.
A. Cold/warm
B. Warm/cold
C. Wet/dry
D. Dry/wet
9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
A. Technician A only
B. Technician B only
C. Both Technicians A and B
D. Neither Technicians A NOR B
10. What part should be removed to test cylinder compression on a diesel engine?
A. An injector
B. An intake valve rocker arm and stud
C. An exhaust valve
D. A glow plug
Answer: See explanation
Explanation:
1. How is diesel fuel ignited in a warm diesel engine?
B. Heat compression
2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
4. The three phases of diesel ignition include:
C. Ignition delay, repaid combustion, controlled combustion.
5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
D. Water-fuel separator
6. The diesel injection pump is usually driven by a _________________.
A. Gear off the camshaft
7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
C. High-pressure common rail
8. Glow plugs should have high resistance when _____________and lower resistance when __________________.
B. Warm/cold
9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
D. Neither Technicians A NOR B
10. What part should be removed to test cylinder compression on a diesel engine?
D. A glow plug
any one know the diffrence in a 12v and 24v cummins?
other than the time peorides and the number of vaulve rods
whats the better one?
please dont answer unless u know adout cars
(and Yes katie this is educational)
Explanation:
The 24v is a higher-revving motor, thus you'd probably want the 4:10. The 12v has better low-end grunt and wont spin as fast, so the 3.54 would work better. Bombing is easier with the computer trucks, and cheaper with the mechanical trucks.
24V are much louder than a 12V at the engine.
While the 12-valve is a little bit more reliably with the mechanical P7100 pump, tuning it requires modified parts of the injection pump. The 24-valve might not be as insanely reliable, but it's still very reliable and can easily be tuned with a handheld tuner.
Technician A says that a lack of lubrication on the back of the disc brake pads can cause brake noise. Technician B says that pads that are not correctly crimped to the caliper housing can cause brake noise. Which technician is correct?
Answer:
Technician A and B both are correct.
Explanation:
According to Technician A, we can stop noise by applying lubricant (Break friction).
According to Technician A, we can stop noise by set-up right position for break pad.
According to the rules of dimension how should written notes appear
Explanation:
Leaders for notes should be straight, not curved, and point to the center of circular views of holes wherever possible. Leaders should slope at 45°, 30° or 60° with horizontal but may be made at any convenient angle except vertical or horizontal.
Drawing pictures of possible designs describes which step of the engineering design process?
Answer:
In prototype making first step is to make basic picture of the projrct.
A prototype is an operating version of a solution. Often it is made with different materials than the final version, and generally it is not as polished. Prototypes are a key step in the development of a final solution, allowing the designer to test how the solution will work.
Explanation:
13. The members installed vertically over and under a window opening are called
studs.
a. Cripple
b. Valley
C. Ridge
Explanation:
Cripples are vertical framing members that support a sill or saddle.
They are installed at points where a common stud would have stood if not for the window opening.
Cripples provide support for the window and the sill it rests on.
why do computers use 1 and 0
I like ya cut g
Explanation:
bonK no Uhm
Answer:
Computers use binary - the digits 0 and 1 - to store data
Explanation:
Computers use binary - the digits 0 and 1 - to store data The circuits in a computer's processor are made up of billions of transistors . A transistor is a tiny switch that is activated by the electronic signals it receives. The digits 1 and 0 used in binary reflect the on and off states of a transistor.
Which statement about iso 9000 is true
Answer:
mate what statement because if you mean just 9000 a true number then that's true
Explanation:
7. In Fleming's left hand rule what do the
following represent:
First finger:
Second finger:
Thumb:
Answer: See explanation
Explanation:
Fleming’s Left-Hand Rule is simply used to know a conductor's direction of force in an electric motor in a scenario where the direction of the magnetic field and the current are already known.
In Fleming's left hand rule, the following are represented:
First finger: This represents the direction of the magnetic field.
Second finger: This represents the direction of the current.
Thumb: This represents the direction of the motion that is acting on the conductor.
Marks
Q 16.
Which one of the following is not a
feature of Microsoft Access?
Answer:
A Data redundancy
099
B. Facilitates sharing
Dos
C. To assess the
099
D. Allows you to
Answer:
i think C
Explanation:
if not really sorry
Which of the following describes the purpose of exercise physiology?
to improve the efficiency of body systems
to understand how to control muscles during exercise
to improve methods for the body to endure exercise
to understand how the body adapts to exercise
Answer:
to understand How the body adapts to exercise
The purpose of exercise physiology is to understand how the body adapts to exercise. So the answer is (4).
What is physiology about?Exercise physiology is a field of study that examines how the body responds to physical activity. It looks at how exercise affects the cardiovascular system, respiratory system, muscular system, and other body systems. Exercise physiology also studies how exercise can be used to improve health and fitness, and to treat or prevent diseases.
The goal of exercise physiology is to understand how the body adapts to exercise so that we can use this knowledge to improve people's health and well-being. By understanding how the body adapts to exercise, we can design exercise programs that are safe and effective for people of all ages and fitness levels.
The correct option is 4.
Leaen more about physiology
https://brainly.com/question/30764374
#SPJ2