Answer:
C
Explanation:
Fish swim by flexing their bodies and tail back and forth. Fish stretch or expand their muscles on one side of their body, while relaxing the muscles on the other side. This motion moves them forward through the water. Fish use their back fin, called the caudal fin, to help push them through the water.
Answer: c
Explanation:
Which statistical process control (SPC) tool is described in these sentences?
is a statistical process control (SPC) tool that helps identify the causes of a particular problem. is a SPC tool that helps to visualize the steps in a process and identify gaps in the process.
Answer:
is a SPC tool that helps to visualize the steps in a process and identify gaps in the process.
The raised areas between the grooves in a rifled bore are called:.
Answer:
The raised portions of the rifling are known as lands and the recessed portions are known as grooves. When a weapon is fired, these lands and grooves cut into the bullet, putting spin on it as it travels through the barrel of a firearm. Because bullets have an oblong shape, spin is necessary for accurate flight
How can the most common accidents which occur when using cranes be
reduced?
Answer:
Follow standard safety guidelines when operating a crane
Pay attention to and follow the crane load chart
Inspections should be carried out by competent workers
Allow only qualified workers to operate a crane
Most common accidents associated with the use of cranes can be reduced by following the appropriate safety measures in a factory or an industry.
What are safety measures?Safety measures are actions and precautions of obedience done to increase safety and decrease danger to human health. It is a precautionary step done to improve or assure safety or protection from damage and disaster caused in a factory or an industry.
Therefore, in a factory where cranes are being used, the most common accidents can be reduced and eliminated by following some of these precautions.
Inspection: Carefully check if the bolts and nuts of the cranes are tightly connected together.There should not be any movement under the crane when the crane is in motionThe use of cranes in the factory should only be handled by an expert and qualified personnel.Learn more about safety measures here:
https://brainly.com/question/14367881
what type of crank shaft is needed in a V8 engine
Answer:
Flatplane or crossplane.
Explanation:
It depends on the engine and reason. Most v8 engines from manufactereres produced today have flatplane crankshafts.
When operating a crane, which of the following is an important safety precaution? Select all that apply.
Select the 3 answer options that apply.
Ensure that all worksite personnel are qualified crane operators
Check for overhead power lines
Ensure your area of travel is clear
Never lift people
When operating a crane, the important safety precautions are:
B. Check for overhead power lines.
C. Ensure your area of travel is clear.
D. Never lift people.
What is a crane?A Crane machine is one that is used to lift heavy objects. They're commonly used in construction sites and car towing. Cranes are also of different kinds for different purposes, one of one kind is a balanced crane that is balanced in a point called a fulcrum. This is also used to leave heavy objects, and it means very little force.
Is operated by humans, and proper safety precautions should be taken the driver should wear a helmet, and they should check before starting the crane it should never have left people it can be harmful and deadly.
Therefore, the correct options are B, C, and D.
To learn more about crane machines, refer to the below link:
https://brainly.com/question/14765960
#SPJ2
a digital multimeter is set to read dc volts on the 4 volt scale the meter leads are connected to a 12 volt battery what will the display read
Answer: The answer
The answer is D. 0.012 V
Explanation:
0.012 V will the display read, as a digital multimeter is set to read DC volts on the 4 volt scale the meter leads are connected to a 12 volt battery.
What is digital multimeter?Voltage, current, and resistance are just a few of the electrical stimuli that a digital multimeter, or DMM, measures and verifies.
It combines the functions of a voltmeter, an ammeter, and an ohmmeter and is common diagnostic equipment used by technicians and electrical engineers.
Thus, it is 0.012 V
For more details about digital multimeter, click here:
https://brainly.com/question/5135212
#SPJ2
You are replacing the spark plugs on a 3.4L (VIN E) engine. Is it
necessary to remove the upper intake manifold?
Answer:
First off, you shouldn't replace spark plugs.
Explanation:
Trust me, spark plugs last forever and you should clean them and put them back in. Changing spark plugs is propaganda created by corporations to make more money.
Technician A says that one function of oil is to clean. Technician B says that one function of oil is to cushion. Who is correct
Oil can serve both purpose in these context, to clean and to cushion
Both Technician A and B are correct
Functions of oiloil is used in machine parts majorly as lubricants to prevent wear and tear of machine parts, they also double as coolants, hence they transfer and distribute heat to prevent stalling due to over heating of parts
Learn more about engine oil here:
https://brainly.com/question/25614315
A machinist creates a solid steel part for a wind turbine. The part has a volume of 1015 cubic centimeters. Steel can be purchased for $0.29 per gram, and has a density of 0.795 g/cm3. If the machinist makes 500 of these parts, what is the cost of the steel, to the nearest dollar
Answer:
$234
Explanation:
[tex]cost=volume*density*cost per gram = 1015cm^{3} *0795g/cm^{3} *0.29dollars/g=234 dollars[/tex]
As per the given data, the cost of steel for 500 parts will be approximately $116891.
What is wind turbine?A wind turbine is a machine that converts wind's kinetic energy into electrical energy.
To find the cost of the steel for 500 parts, we need to first find the mass of steel required to make one part.
Density of steel = 0.795 g/cm^3
Volume of one part = 1015 cubic centimeters
Mass of one part = Density x Volume = 0.795 x 1015 = 806.425 grams
So, to make 500 parts, the total mass of steel required will be:
Total mass = 500 x 806.425 = 403212.5 grams
The cost of steel per gram is $0.29, so the total cost of the steel for 500 parts will be:
Total cost = Total mass x Cost per gram = 403212.5 x 0.29 = $116891.13
Rounding this to the nearest dollar, the cost of steel for 500 parts will be approximately $116891.
Thus, the answer is $116891.
For more details regarding wind turbine, visit:
https://brainly.com/question/928271
#SPJ2
if this is that and that is this then this is that
Answer:
that is this so that is this
Explanation:
Technician A says if routine maintenance is not performed, it usually costs more money to fix as an unexpected repair and possible tow. Technician B says if your car is new, check to see if the repair is covered under the warranty. Who is correct?
Answer:
A.
Explanation:
Routine maintenance often spots trouble before it begins to show up.
If you fail to do routine maintenance warranty repairs may be void due to neglect.
Could actually be tricky and both A and B. If routine maintenance turns up a needed repair, for sure check the warranty coverage.
Engine without VVT often sacrifices high end performance for low end torque.
True or false
Answer:
true
Explanation:
im not even an engineer and ik this, lol. variable valve timing is goated in my BMW tho
Write 483,928 in each form.
Word:
Expanded
Answer:
four hundred thousand, blah blah blah, blah blah blah
Explanation:
What types of engineers would be most likely to work on the project described in the following scenario?
A small town in Massachusetts received a government grant for developing a series of bicycle trails through a salt marsh.
A.)a construction engineer, an environmental engineer, and a structural engineer
B.)an environmental engineer, a structural engineer, and a transportation engineer
C.)an environmental engineer, a transportation engineer, and a water resource engineer
D.)an environmental engineer, a structural engineer, and a transportation engineer
Answer:
I believe that it is option c.
Does the sum exterior measure of all regular and irregular polygons always equal to 360° ?
Answer:
One important property about a regular polygon's exterior angles is that the sum of the measures of the exterior angles of a polygon is always 360°.
Explanation:
HOPE MY ANSWER HELPED<3 HAVE A WONDERFUL DAY
Shawna has been working to develop a new wheelchair that can easily convert from on-road wheels to off-road wheels. t even has a lever that can allow it to drive easily and safely through snow and ice. She has identified the needs of her client, brainstormed designs, and explored possible solutions. Her plan is now set. Which of the following states the next step in the process?
She should now move on to the next problem.
She should gather her team, inform them of the plan, and begin working on a prototype to test her design.
She should investigate other vehicles that can transport people across various types of terrain.
She should collaborate with her team to sell the blueprints of her idea online.
She should gather her team, inform them of the plan, and begin working on a prototype to test her design.
That's the only reasonable choice because:
- She can't move on to another problem due to her already solving it earlier.
- She can't just sell her idea since she is the one developing.
- She can investigate the terrains but the idea is to switch wheels with a lever.
Answer:
She should gather her team, inform them of the plan, and begin working on a prototype to test her design. So "B" is correct.
Explanation:
Its "B" on EDGE 2021 Engineering :D
2. Identify the structural members specified in the drawings below.
A
В.
С.
Subfloor
D.
E.
F.
Answer:
where is the drawing bro
What parts does the block contain?
Answer:
Cylinder blocks.
Cylinder liners.
Coolant passages.
Oil passages.
Crankcase.
Integrated crankcase.
Integrated cylinder head.
Integrated transmission.
Explanation:
2. The unthreaded part of a bolt or screw is called the
Answer:
The grip
Explanation:
the head of all headed bolt (except countersunk head bolt)
any unblocked video sights for school ?
Answer:
I'm not sure what you mean
Explanation:
How old must you be to operate a forklift
Write two main advantages of digital communication system over analog commu-
nication system.
Answer:
Increased range.
Better voice quality.
Noise preservation and noise reduction.
Deliver more information.
Greater portability and flexibility.
Simple to use.
I hope I helped
I left my leveno computer on my bed and didn’t touch for a while mind you it was working but then I came back and it was closed and the screen was black even if like it would open and I think that’s because I dropped my phone on the F11 button and I didn’t know what it did and now
It still has the time screen and then you press it and it go back to like a light up black screen pls help me I have school at 9:30
Answer:
Try restarting your computer this would typically be pressing the power button for about 15 seconds. Pressing f11 shouldnt have done anything because that is typically used to make something fullscreen
Explanation:
The proper way to start cutting materiala circular saw is to _.
Answer:
scissors?
Explanation:
Answer:
rev the saw to full speed and slowly move it forward into the material
Explanation:
There are many types of saws and one of which is the "circular saw." It functions by providing a frame for anything that you're working on.
When using a circular saw, it is very important to consider the precautions and the proper steps in using and handling it. It is important to rev the saw to full speed and slowly move it towards the material you're working on. This prevents the blade from being compressed. This results to a fine way of cutting through and gives you a well-cut output.
Which of the following famous structures has an imaginary line that connects the center of the base with the vertex? *
A. Aloba Arch
B. Rainbow Bridge National Monument
C. Great Wall of China
D. Great Pyramids of Egypt
Select only three polyhedral shapes.
1. sphere
2. prism
3. column
4. cone
5. pyramid
6. cube
Answer:
CubeSphere ComeExplanation: A three -dimensional shape with flat polygonal faces , straight edges and sharp corners or verticesThis style is closest to the cuisine enjoyed by French royalty and nobility.
А
Nouvelle cuisine
B
Cuisine bourgeoise
С
Haute cuisine
D
Cuisine classique
Answer: С
. Haute cuisine
Explanation:
Haute Cuisine is typically associated with higher level establishments due to the time and cost it takes to prepare as it involves meticulous preparation and usually uses exotic ingredients which make it quite expensive.
It is therefore no wonder that it came to be in order to feed the 'privileged' people in France being the French Royals and Nobles in the 17th century. It differed from normal cooking at the time by using exotic ingredients such as tongue and caviar and as such, gave those who ate it a feeling of superiority.
!WILL GIVE BRAINLIEST!! Explain the difference in the work performed by an environmental scientist and a civil engineer during the development of a geothermal site.
Answer:
What is environmental science?Environmental science is a wide field that combines disciplines and methodologies from the biological, information, chemical and physical sciences to study the environment and the impact from external factors like urban development and population growth. Environmental scientists and professionals working in the field collect and analyze data from nature, small communities and large urban areas to determine an area's pollution and contamination risk. Through the collection and analysis of data from the environment, professionals can assess soil health, water usability and accessibility and other factors that can affect both citizens and the environment.
Explanation:
What is environmental engineering?Environmental engineering is a field in engineering where professionals focus on combining environmental science methods with engineering principles to develop and implement better infrastructure, technology and industrial operations that reduce the risk of environmental contamination and pollution. Environmental engineers may often collaborate closely with environmental scientists to apply data to designs that promote cleaner energy use, more efficient building activities and ecologically sound business practices.Additionally, environmental engineering often includes other fields that overlap to form a foundation for this career path. For instance, environmental engineers may also incorporate aspects of civil engineering, transportation and logistics, geotechnical engineering, chemical engineering and biology to develop strategies that reduce the risk of pollutants and contaminants from urban projects and other activities that can impact the environment.
Difference between these both engendering Even with the overlap in some of the collaboration and application methods of both environmental career fields, there are several key differences between environmental engineering and environmental science:Career focusOne important distinction between environmental science and engineering is the career focus. Environmental scientists focus on the collection and analysis of data and the assessment of hypotheses they make based on information they gather from the environment. Environmental engineers' focus is the application of the data scientists and technicians analyze in order to produce outcomes that reduce pollution, increase environmental efficacy and ensure construction projects comply with local, state and federal environmental policies. Environmental science gives information to engineering professionals with the goal of reducing the impacts of development and population growth.Essential job dutiesEnvironmental scientists and technicians may spend a majority of their careers working within laboratory settings to test environmental samples and form studies around the data they collect from the environment. Outdoors, environmental scientists study natural resources and elements for signs of contamination or pollution and collect samples for laboratory analysis.An environmental engineer, conversely, uses the information from environmental scientists to make decisions on project designs, mitigation strategies and construction activities. In addition, engineers collaborate with other professionals like urban planners and regional directors to plan projects that support environmental and community health and safety. The strategies engineers apply in their careers ultimately work to reduce and repair environmental impact and damage.Average salaryAccording to Indeed's salary information, the salary averages for an environmental scientist and environmental engineer also differ. While an environmental scientist can earn an average of $71,939 per year, an environmental engineer can have an earning potential of $83,893 per year. Several factors can affect the average income you can earn in both career fields, though. For instance, your degree level and experience level can impact your starting salary, and some employers may pay higher salaries for special certifications. Additionally, your location can also affect your earning potential, where some areas have higher income averages than others. And more
if I were to build a fully functional robotic leg what type of circuit board should I use?
Answer:
A good one
Explanation:
Rotatianal degrees and stuf for different types of movement would take some proccesing power and if it were linked to brain neurons you would need one not prone to frying
Which uses combustion to transfer thermal energy to warm a building?
O heat engine
O furnace
refrigeration unit
O heat pump
Answer:
Furnace
Explanation:
Furnace typically uses a propane or natural has heat exchanger. High efficiency units will vent with PVC (condensing flue gas), lower efficiency in metal flue pipe.
Answer:
B. Furnace
Explanation:
A. X
B. O
C. X
D. X