Answer:
Y=8
Explanation:
Y=4
X=10
if x is 20 it means it is doubled frm the previous therefore it means even y has to be doubled
first. now
x=10. x=20
y=4. y=8
a squirrel runs at a speed of 9.9 m/s with 25 J of kinetic energy
What is the squirrels mass
Answer:
yeet yeet yeet yeet
Explanation:
Kinetic energy (K.E):-
So, the Mass of the Squirrel is 0.51 Kg (or) 510 grams.
A squirrel runs at a speed of 9.9 m/s with 25 J of kinetic energy.
What is the squirrel’s mass?
Answer: 0.51 kg
A hollow tennis ball and a solid steel ball of the same diameter are dropped at the same time. Which ball has the greater force acting on it
Answer:
the solid steel ball...more mass more weight more gravity
Explanation:
Answer:
Solid steel ball. It has more mass therefore more force will be acting on it.
Explanation:
I WILL GIVE U 100 POINTS IF U ANSWER THIS AND GET IT RIGHT!!!!!!!!!!!!!!
Answer:
Free points That's awesome Thanks Brainly User!
Explanation:
Erin was asked to design an experiment that would give the evidence needed to support the hypothesis: “A 6 inch playground ball will bounce higher than a 3 inch playground ball, because it is bigger.” Which of the following statements would not be a part of Erin’s experiment?
Determining all of the variables.
Repeating her experiment 5 times.
Recording her results as well as her observations.
Dropping the balls from different heights.
It takes serina 0.25 hours to drive to school. Her route is 16km long . What is serina’s average speed on her drive to school
Explanation:
distance=16km=16000m
time=0.25hours=1/4hr=15min=900sec
speed=dist./time
=16000/900=160/9=17.777m/s
speed=17.78m/s (rounded)
Answer:
64
Explanation:
Avg. speed = total distance/total time
Avg. speed= 16km/0.25h
Avg. speed= 64km/h
Queremos un cilindro de simple efecto que utilice en su funcionamiento un volumen de aire a presión atmosférica de 13,122 litros, cuya presión de trabajo sea de 8,5Kgf/ cm2 y cuya longitud sea de 20 cm. -hallar el diámetro de este cilindro. - calcular las fuerzas de este cilindro.
Answer:
1) El diámetro es de aproximadamente 913,987 cm.
2) La fuerza del cilindro es 5576850 kgf
Explanation:
1) Los parámetros dados son;
El volumen del aire = 13,122 litros = 13122000 cm³
La presión de trabajo = 8.5 kgf / cm²
La longitud del cilindro = 20 cm.
Por lo tanto, tenemos;
El área de la base del cilindro = π · r² = 13122000 cm³ / (20 cm) = 656100 cm²
r = √ (656100 / π) ≈ 456,994 cm
El diámetro = 2 × r ≈ 2 × 456.994 ≈ 913.987 cm
El diámetro ≈ 913,987 cm
2) La fuerza del cilindro = El área de la base del cilindro × La presión de trabajo
∴ La fuerza del cilindro = 656100 cm² × 8.5 kgf / cm² = 5576850 kgf
La fuerza del cilindro = 5576850 kgf
What is true about the atom? Select all that are correct.
Is made up of protons, neutrons and electrons
Make up the matter in the universe
Are found in nonliving matter only
Is found only on Earth
a is about the same size as a cell
Smallest unit of matter that keeps its chemical properties
Answer: Is made up of protons, neutrons and electrons
Make up the matter in the universe
Smallest unit of matter that keep its chemical properties
what angle is formed by the sun, earth, and moon during an eclipse?
A.180 degree
B.270 degree
C.90 degree
D.45 degree
question in the photo
How do bubbles support the atomic theory?
A. The bubbles are lighter than air.
B. There is matter that cannot be seen inside the bubbles.
C. The bubbles will burst before long.
D. The bubbles cannot be broken into smaller pieces.
Answer:
The answer is probably B or C
Option B supports the atomic theory. Thus, this option is correct.
Atomic theory is the theory which states that matter is composed of particles called atoms. It tells us that all the matters are made of very tiny particles called atoms and all atoms of the same kind have the same size in any object.
Let's look at all the options given,
A-The bubbles are lighter than air- The bubble consists of water and air thus they are not lighter than air. This statement does not tell anything about the atomic theory. Hence this option is not correct.B. There is a matter that cannot be seen inside the bubbles-The bubble is made up of two kinds of atoms one is oxygen and another is hydrogen. When we feel air into a soap bubble solution molecules want to attract to each other again so they wrap around the burst of air to attach to each other again. These atoms cannot be seen inside the bubbles but this option support the atomic theory. Thus, this option is correct.C. The bubbles will burst before long-In the bubble there is water. When this water loss in some way the bubble pops up. This water can be lost when it comes to contact with dry fingers or objects. It can be burst when the atmosphere is very dry. All the atoms are attracted towards. D. The bubbles cannot be broken into smaller pieces-This option does not support the atomic theory thus this is not the correct option.
Hence the option B supports the atomic theory. Thus, this option is correct.
For more about the atoms follow the link below-
https://brainly.com/question/13981855
Which of the following is the minimum amount of work done by a hydraulic lift
to raise a 150-kg aluminum block 2.0 m vertically?
Answer: 300 J
Explanation:
Force = 150 KJ
Distance = 2.0 m
The minimum amount of work done by a hydraulic lift to raise a 150-kg aluminum block 2.0 meters vertically would be 2940 Joules, as the work done is the product of the force applied to the displacement of the object, therefore the correct answer is option B.
What is work done?The total amount of energy transferred when a force is applied to move an object through some distance
The work done is the multiplication of applied force with displacement.
Work Done = Force × Displacement
As given in the problem we have to find out the minimum amount of work done by a hydraulic lift to raise a 150-kg aluminum block 2.0 meters vertically.
The minimum work done = 150 × 9.8 × 2
= 2940 Joules
Thus, The minimum amount of work done by a hydraulic lift to raise a 150-kg aluminum block 2.0 meters vertically would be 2940 Joules.
To learn more about the work done, refer to the link given below ;
brainly.com/question/13662169
#SPJ6
An airplane cruising at a constant velocity and altitude. Which of the following diagrams best represents the four forces of the airplane?
Answer:
You need to put the diagrams. repost and include the diagrams
please help! i'll give brainliest.
what is it called when a magnet causes the atoms in a non-magnetic metal to line up and act like a magnet?
a: oriented magnet
b: permanent magnet
c: non-magnet
d: induced magnet
Answer:
I think It's induced magnet
Explanation:
Because a magnet and non magnet can be chicken nuggets
If a magnet causes the atoms in a non-magnetic metal to line up and act like a magnet, the non magnet is said to be an induced magnet by the magnetic induction by a permanent magnet.
What is magnetic induction ?A permanent magnet is made of ferromagnetic materials which are having permanent magnetic properties. The magnetic field lines from permanent magnet always align with an applied magnet.
As in the case of dipole molecules capable of inducing a polarity to a nonpolar molecule, a magnetic field by a strong magnet can induce a magnetic property to a nonmagnet.
The induced magnetic field only reside in the object as long as the induction source is there. For example the a rotating electric filed causes magnetic moment in a nonmagnet.
Find more on magnetic induction:
https://brainly.com/question/18575018
#SPJ5
A 1500 kg car has an applied forward force of 5000 N and experiences an air resistance of 1250 N. What is the car's acceleration?
Answer:
[tex]2.33\ m/s^2[/tex]
Explanation:
Net Force
According to the second Newton's law, the net force exerted by an external agent on an object of mass m is:
Fn = m.a
Where a is the acceleration of the object. The net force is the sum of the individual vector forces applied to the object.
The m=1500 Kg car has two horizontal forces applied: the forward force of 5000 N that causes the movement and the air resistance force of 1250 N that opposes motion.
The net force is Fn = 5000 N - 1500 N = 3500 N
To find the acceleration, we solve the equation for a:
[tex]\displaystyle a=\frac{Fn}{m}[/tex]
[tex]\displaystyle a=\frac{3500}{1500}[/tex]
[tex]\boxed{a = 2.33\ m/s^2}[/tex]
The car's acceleration is [tex]a = 2.33\ m/s^2[/tex]
- During a certain period, the angular position of a rotating object is given by: = − + , where is in radian and t is in seconds. Determine the angular position, angular speed, and angular acceleration of the rotating object at = Sec.
The question is not complete. The complete question is :
During a certain period of time, the angular position of a rotating object is given by [tex]$\theta =2t^2 +10t+5$[/tex], where θ is in radians and t is in seconds. Determine the angular position, angular speed, and angular acceleration of the door (a) at t = 0.00 seconds, (b) at t = 3.00 seconds.
Solution :
Given :
Displacement or angular position of the object, [tex]$\theta =2t^2 +10t+5$[/tex]
∴ Angular speed is [tex]$\omega = \frac{d \theta}{dt}$[/tex]
ω = 10 + 4t
And angular acceleration is [tex]$\alpha = \frac{d \omega}{dt}$[/tex]
α = 4
a). At time, t = 0.00 seconds :
Angular displacement is [tex]$\theta =2t^2 +10t+5$[/tex]
[tex]$\theta =2(0)^2 +10(0)+5$[/tex]
= 5 rad
Angular speed is ω = 10 + 4t
ω = 10 + 4(0)
= 10 rad/s
Angular acceleration is α = 4 [tex]$rad/s^2$[/tex]
b). At time, t = 3.00 seconds :
Angular displacement is [tex]$\theta =2t^2 +10t+5$[/tex]
[tex]$\theta =2(3)^2 +10(3)+5$[/tex]
= 53 rad
Angular speed is ω = 10 + 4t
ω = 10 + 4(3)
= 22 rad/s
Angular acceleration is α = 4 [tex]$rad/s^2$[/tex]
How much work is required to lift a 500 kg block 12 m? (Show work)
The required work done will be "6000 kg-m".
Work and energy:Work would be defined as an object's displacement whenever a force would be exerted to that as well, whereas energy is defined as the capacity to accomplish the work.
This then exists throughout a variety of forms, including potential, kinetic, biochemical, thermodynamic, nuclear, as well as direct current.
According to the question,
Mass, m = 500 kg
Distance, d = 12 m
We know the formula,
→ Work = Force x Distance
or,
→ W = F x D
By substituting the given values in the above formula, we get
= [tex]500\times 12[/tex]
= [tex]6000[/tex] kg-m
Thus the above answer is correct.
Find out more information about work done here:
https://brainly.com/question/25573309
Which cell structure is found in plant cells, but not in animal cells?
Answer:
Cell wall and chloroplasts (only for leaves)
Explanation:
All plant cells have cell walls to give the cell a fixed shape but animal cells do not have cell walls. Some cells like leaf cells have chloroplasts to make their own food for the plant while animal cells do not have chloroplasts.
Calculate the mass of a planet that exerts a 1.5 X 10 13 N force on a 5.4 x 10
30
kg star
O 6.67 X 10 3 kg
O 1.07 X 10 15 kg
O 1.00 X 10 17 kg
O 1.30 X 10 45 kg
Answer:
umm I also need help sorry
Explanation:
help..
Answer:
1.07 X 10^15 kg
Explanation:
Two soccer players run toward each other. One player has a mass of 85 kg
and runs west with a speed of 8 m/s, while the other has a mass of 105 kg
and runs east with a speed of 7 m/s. What is the total momentum of the
system made up of the two players?
Answer:
Total momentum, p = 55 kg-m/s
It is given that,
Mass of player 1, m₁ = 85 kg
Mass of player 2, m₂ = 105 kg
Speed of player 1, v₁ = -8 m/s (west)
Speed of player 2, v₂ = 7 m/s (east)
Momentum is equal to the product of mass and velocity. For this system, momentum is given by :
p=m_1v_1+m_2v_2p=m
1
v
1
+m
2
v
2
p=85\ kg\times (-8\ m/s)+105\ kg\times 7\ m/sp=85 kg×(−8 m/s)+105 kg×7 m/s
p = 55 kg-m/s
The total momentum of the system made up of the two players is 55 kg-m/s.
Answer:
p = 55 kg * m/s east
Explanation:
The answer above explains it neatly, but leaves the direction out of the answer. The player heading east has more momentum, so the net momentum of the system is east.
A body moving in a straight line has a uniform motion if it travels ---------- distance in -------- intervals og time
Answer:
uniform an uniform
please fill it like yhis
Solve for x. 60(cos 50) = x
Answer:
x=38.56725658
Explanation:
Answer:
x=38.56725658
Explanation:
When an object moves, where does the energy come from?
Answer:
Kinetic energy.
Explanation:
This is the energy of motion, observable as the movement of an object or subatomic particle. Every moving object and particle have kinetic energy.
Yuna is writing an opinion piece about her Schools lunch menu which text structure would best Express her ideas check all that apply
Answer:
Cause and effect, problem and solution, order of importance, comparison and contrast.
Explanation:
Beth moves a 15 N book 20 meters in 10 seconds. How much power was produced?
Answer:
30 Watts
Explanation:
Power = Work/Time
Work = Force*Distance
Power = Force * Distance / Time
Power = 15 N * 20 meters / 10 sec
Power = 30 Watts
A block and tackle consisting of 5 pulleys is used to raised a load of 400N through a height of 10m.If the work done against friction is 100j.
Calculate;
1)The work done by the effort
2)The efficiency of the system
3)The effort applied
Answer:
1) 4000Joules
2) 25%
3) 320N
Explanation:
A block and tackle consisting of 5 pulleys is used to raised a load of 400N through a height of 10m.If the work done against friction is 100j.
Calculate;
1)The work done by the effort
2)The efficiency of the system
3)The effort applied
1) Workdone by the effort is the work input = Load * distance moved by the Load
Workdone by the effort = 400 * 10
Workdone by the effort = 4000Joules
2) Efficiency = Work output/Work input * 100
Work output = work done against friction = 100 Joules
Efficiency = 100/4000 * 100
Efficiency = 10000/4000
Efficiency = 25%
Hence the Efficiency of the system is 25%
3) Using the efficiency formula:
efficiency = MA/VR * 100
Velocity ratio = 5
MA = Load/Effort
efficiency = (L/E)/5 * 100
25 = 400/E/5 * 100
25/100 = 400/5E
0.25 = 400/5E
0.25 * 5E = 400
1.25E = 400
E = 400/1.25
E = 320N
hence the effort applies is 320N
A container with a mass of 5 kg is lifted to a height of 8 m. How much work is done by the gravitational force
Answer:
work done=392J
Explanation:
work done =Mgh
DATA
M=5kg
g= 9.8
h=8m
W=Mgh
W=5*9.8*8
W=392J
The work done by the gravitational force is equal to -400 J.
What is gravitational force?The gravitational force can be described as a force that attracts a body towards the center of the earth or any physical object that has mass. Every object has mass and exerts a gravitational pull on another object with mass.
Given, the mass of the container, m = 5 Kg
The height from the ground level, h = 8 m
The work done can be calculated by using the below-mentioned formula:
[tex]W = m\times g\times h[/tex]
Where g is the gravitational acceleration.
As the container is lifted in the upward direction therefore the value of the g will be negative.
Substitute the values of m, g, and h in the above formula:
W = 5 × (-10) × 8
W = -400 J.
The negative sign shows that the work is done against the gravitational force.
Therefore, the work done by the gravitational force is equal to -400 J.
Learn more about gravitational force, here:
brainly.com/question/24783651
#SPJ6
Please help me I swear will mark you brainiest
Answer:
B
Explanation:
I hope this helps!!! <3
Answer:
B.......
Explanation:
Hope this helped
State two devices that transfer heat out of a cool environment into a warm environment
Answer:
Heat pump
Refrigerators
Explanation:
Some devices like heat pump and refrigerators used transfers of thermal energy in a cool region to warm other region.
These types of devices used for transferring heat energy by thermal conduction method.
An illustration of a ball sitting at the top of a hill of height labeled h Subscript 1 Baseline = 2 m. A the the bottom of the hill it levels off and the leveled surface is at a height labeled h Subscript 2 Baseline = .5 m. A ball is released from the top of a hill. How fast is the ball going when it reaches the base of the hill? Approximate g as 10 m/s2 and round the answer to the nearest tenth. m/s
Answer:
5.5 m/s
Explanation:
Right on Edge
The statement explains the importance of enzymes that check for and repair mistakes during DNA replication is the enzymes prevent many genetic mutations from being expressed. Thus, the option C is correct.
What is RNA polymerase?RNA polymerase is an enzyme that aids in the transcription of DNA into RNA during transcript in the nucleus. The enzymes prevent many genetic mutations from being expressed.
Primase is an enzyme that synthesizes short RNA sequences called primers. These primers serve as a starting point for DNA synthesis during replication as the DNA polymerases cannot begin the synthesis of the new strand, they only extend it after primase begins it and primase produces RNA molecules, the enzyme can be said to be a type of RNA polymerase.
Therefore, The statement explains the importance of enzymes that check for and repair mistakes during DNA replication is the enzymes prevent many genetic mutations from being expressed. Thus, the option C is correct.
Learn more about genetic mutations on:
brainly.com/question/1282397
#SPJ6
plzzzz help me will mark u brainiest
Answer:
D
Explanation: