Briefly describe an idea for a new product while thinking mainly about it cost analysis to depict what kinds of direct and indirect cost will be involved in its creation
can you give more of an explanation to what the product need sti be
Which is the correct way of dual dimensioning using the position method
Answer:
by placing one of the two measurements below the other or by separating them with a stroke
Explanation:
I had a test on this and it was correct
please answer fast. With full step by step solution.
Let f(z) = (4z ² + 2z) / (2z ² - 3z + 1).
First, carry out the division:
f(z) = 2 + (8z - 2) / (2z ² - 3z + 1)
Observe that
2z ² - 3z + 1 = (2z - 1) (z - 1)
so you can separate the rational part of f(z) into partial fractions. We have
(8z - 2) / (2z ² - 3z + 1) = a / (2z - 1) + b / (z - 1)
8z - 2 = a (z - 1) + b (2z - 1)
8z - 2 = (a + 2b) z - (a + b)
so that a + 2b = 8 and a + b = 2, yielding a = -4 and b = 6.
So we have
f(z) = 2 - 4 / (2z - 1) + 6 / (z - 1)
or
f(z) = 2 - (2/z) (1 / (1 - 1/(2z))) + (6/z) (1 / (1 - 1/z))
Recall that for |z| < 1, we have
[tex]\displaystyle\frac1{1-z}=\sum_{n=0}^\infty z^n[/tex]
Replace z with 1/z to get
[tex]\displaystyle\frac1{1-\frac1z}=\sum_{n=0}^\infty z^{-n}[/tex]
so that by substitution, we can write
[tex]\displaystyle f(z) = 2 - \frac2z \sum_{n=0}^\infty (2z)^{-n} + \frac6z \sum_{n=0}^\infty z^{-n}[/tex]
Now condense f(z) into one series:
[tex]\displaystyle f(z) = 2 - \sum_{n=0}^\infty 2^{-n+1} z^{-(n+1)} + 6 \sum_{n=0}^\infty z^{-n-1}[/tex]
[tex]\displaystyle f(z) = 2 - \sum_{n=0}^\infty \left(6+2^{-n+1}\right) z^{-(n+1)}[/tex]
[tex]\displaystyle f(z) = 2 - \sum_{n=1}^\infty \left(6+2^{-(n-1)+1}\right) z^{-n}[/tex]
[tex]\displaystyle f(z) = 2 - \sum_{n=1}^\infty \left(6+2^{2-n}\right) z^{-n}[/tex]
So, the inverse Z transform of f(z) is [tex]\boxed{6+2^{2-n}}[/tex].
Coving is a curved edge between a floor and a wall.
O True
O False
Answer:
True.
Explanation:
Jamal has Started all season as a safety. Last season,he was making a backup salary, which is 67% of what starters make. If Jamal is able to renegotiate his contract to the starter rate from the $400,000 he's currently making, what will his next salary be?round to the nearest whole number.
Answer: $597015
Explanation:
Let the salary of the starter be x.
Since Jamal earns $400,000 and makes 67% of what starters make, then this can be written mathematically as:
67% of x = $400000
67% × x = $400,000
67/100 × x = $400,000
0.67 × x = $400,000
0.67x = $400,000
x = $400,000 / 0.67
x = $597014.93
x = $597015
His next salary will be $597015
What is the Energy of moving things?
mechanical
sound
nuclear
Light
Answer: Kinetic energy
Explanation: If you live in a country other than UK you will probably call it something different
Mechanical energy is the answer
Employees who are paid a portion of the profit from the sale of a product or service are paid on a(n) basis.
Compare similarities between the inventions of Thomas Edison and Bill Gated
PLEASE HELP ASAP!!!!!!!!!!!!!!!!!!!!!!!!
Which of the following describe what the material of an object can impact?
achievements and failures
geometric shapes and figures
sustainability and durability
durability and achievement
Answer:
geometric shapes and figuresAnswer:
Sustainability and durability
Explanation:
Bridge Reflection:
You’ve just spent a month either designing or designing & constructing a bridge structure. Reflect (think back on) and write a reflection essay about your recent experience with the bridge structure project. Use multiple paragraphs (2-3 sentences per paragraph) to complete your feedback. Minimum words: 500
for the following questions:
• Now that you’ve spent a month designing/making a bridge, how does it feel to be done?
• What specific steps did you enjoy the most in designing/making your bridge?
• What did you like the least (or not like at all)?
• If you could start all over again today, how would you change your method? What
would you do differently?
• What/Who was most helpful during the process of planning, cutting, and assembling
your bridge (for on campus students)?
• How could this project be improved?
• How could conditions in the shop be improved (on campus students)?
• What other thoughts would you like to share on the bridge structure design project?
Answer:
IT feels proud to be done making a bridge
Explanation:
yo where are the answer :/
Answer:
yaa what he said
Explanation:
You are driving on a multi-lane road, and are following the vehicle in front of you at a safe distance. But then a car changes lanes into the gap in front of you, and slows down because the gap in front o them is too small. You should
A.Honk your horn, and then gradually drop back further behind the slowing car.
B.Quickly try to change lanes, and pass the slowing car if you can.
C.Slow down and drop back to a safe following distance behind the slowing car.
Answer:
C. Slow down and drop back to a safe following distance behind the slowing car.
Explanation:
the highway code contains the rules and regulations guiding the conduct of road users on a motorable roads. It is very important that a driver concentrates on the situation on the road whenever he/she is driving to reduce the event of avoidable accidents.
In the given scenario, since the car that changed lanes slows down due to small gap at its front, the appropriate thing to do is to slow down and follow by keeping a safe distance behind the slowing car.
Answer:
C.Slow down and drop back to a safe following distance behind the slowing car.
Explanation:
I got this correct
what is 18x2?????????????????
Answer:
36
Explanation:
because you add 8+8=16
you add a 1 above the other i then 1x2=2+1 =3
then you put the 6 beside the 3 and get
36
Suppose that you are working in a home that has a 15kw oven that operates on 240 V, The oven is on a branch circuit by itself. What’s the demand load for the oven circuit? Show all of your calculations.
Explanation:
please see it my work solution
When would you normally use a pin punch?
Answer:
the main use of a pin punch is to remove pins from a chain provided the diameter and the length of the shank are compatible with the pin dimensions
help ill give BRAINLYEST ( if it lets me )
Determine what each letter represents in the Punnett square.
Letters A and B represent the genotypes of the ______
.Letters C, D, E, and F represent the genotypes of the _______
ps theres no pic
.
Answer:
Letters A and B represent the genotypes of the Parents
Letters C, D, E, and F represent the genotypes of the Offspring.
Explanation:
The Punnet square is a square shaped figure or diagram used to anticipate the genotypes of offspring after a certain parental cross. It helps in determining the genotype as well as phenotype of the offspring if we know the genotype of parents.
Which of the following can minimize engine effort and
save fuel?
A. Using cruise control
O B. Driving only in low gear
OC.Driving only in increments of 5 mph
D. Changing your oil once a week
The point in an electrical circuit that is connected to the negative side of a power supply is called what?
A. Battery source
B. Ground
C. Loop
OD. Short circuit
Answer:
ground or B
Explanation:
Explain how Peccerelli's team identifies the bodies they find.
Answer:
Two methods are;
DNA
Forensic anthropology
Explanation:
Forensic investigators may use DNA samples to classify suspects or evaluate parentage. A DNA profile is just like a fingerprint.
Digital forensics is a particular sub-field of forensic science that incorporates the application of archaeological skeletal research and methods to solve crime crimes.
Answer:
They identified the bodies using DNA and forensic anthropology and DNA.
Explanation:
Which statement is true?
A.Temperature measures the average kinetic energy of particles.
B.Temperature equivalents indicate the same thermal energy.
C.Temperature depends on the density of the substance.
D.Temperature measures the thermal energy of object.
What is the purpose of the graphic language?
Answer:
enables the representation, analysis and communication of various aspects of an information system. These aspects correspond to varying and incomplete views of information systems and the processes therein.
When could you use the engineering design process in your own life?
Answer:
You could use this process to make a new item or solve a problem that you could be having around the house
I hope this helps!
Explanation:
Samantha has to create a video for her science project on the blossoming of a flower from a bud to one with fully opened petals. Which camera technique should she use to record this video?
A.
genlock
B.
time lapse
C.
cranking
D.
timecode
Answer:
Samantha would have to use the ‘time-lapse’ technique to film the video in the most efficient way.
Explanation:
i got it right
Phil wants to make a dark themed superhero movie. What could be his target demographic?
A.
male, aged 8-15
B.
female, aged 15-23
C.
female, aged 35-43
D.
male, aged 18-25
E.
male, aged 45-53
Answer:
D.
male, aged 18-25
Answer:
D
Explanation:
An example of a good electrical conductor is?
Multiple Choice
Which option best characterizes Reese's choice of less-than-optimal materials in the following scenario?
Reese has just designed a vándshield for an extremely lightweidot car that can be transported by the military via helicopter. The engineers
wanted to use a specially formulated glass that is lighter than ordinary glass, but the cost was far above the budgeted amount for the
project's materials. Reese decides to use a plastic windshield instead.
Economic considerations should never be placed above safety when designing a model
Economic considerations can endanger the safety of a model.
Economic considerations must be considered vihen designing a model
Economic considerations are the most important factor vihen designing a model
Answer:
Economic considerations must be considered when designing a model.
Explanation:
The engineers wanted to use a specially formulated glass which was lighter than ordinary glass for the design requirement of light weight and portability with helicopter. However the cost was very high than the budgeted amount for the material to be used in the project. The alternative was to use a plastic wind shield. In design perspective considering the weight and portability criteria, this will still work .In the economic perspective, the budget will fit. This concludes that economic considerations must be considered when designing a model. Though this factor might not be the most important one , but it helps in ensuring projects budgets are within expected margins.
Answer:
"The client will use the information gathered from the original design and modify the vehicle."
Explanation:
What is the name of the type of rocker arm stud that does not require a valve adjustment?
Answer:
Jesel Premium Stud rockers
Explanation:
This specific stud rocker does not need a valve adjustment. It does not need stud girdles or pushed guide plates. It can be adjusted on a steel stanchion post.
(have a good day and I hope that this explanation fits what you needed to know!)
Which option identifies what must be written in sketches in the following scenario to enable the team to follow the designs?
Ellie has designed a new construction device. She has several sketches that she will present to her team at tomorrow’s meeting.
structural achievements
shapes
coordinate space
vertices
Answer:
I'm pretty sure structural achievements
Technician A states that a pressure bleeder may be needed to bleed EBC system hydraulic circuits. Technician B states that once the scan tool indicates that the HCU is bled, it may direct you to bleed the brakes manually to remove any remaining air from the system. Who is correct
Answer:
Both Technician A and Technician B
Explanation:
ABS modulators such as the Ford EBC310 version which are not equipped with bleeders are to have there valves cycled and their pumps activated to enable the bleeding out areas which are not easily bled by the wheel based bleeding
The brakes can be either pressure bled or bled manually, however, the HCU will require additional processes to completely bleed out the system, such as the use of a scan tool
where has the process of nuclear fusion been occurring for over four billion years
Answer:
Inside the Sun.
Explanation:
Inside the Sun, this process begins with protons (which is simply a lone hydrogen nucleus) and through a series of steps, these protons fuse together and are turned into helium. This fusion process occurs inside the core of the Sun, and the transformation results in a release of energy that keeps the sun hot.