Kartianna is pushing a lawn mower using a force of 300 n. If she pushes the mower a distance of 800 m, how much work has she done?.

Gasoline weighs approximately 6.073 pounds per gallon.

This can vary slightly depending on the temperature and pressure conditions, as well as the specific type of gasoline being measured. However, for most practical purposes, 6.073 pounds per gallon is a good estimate for the weight of gasoline.

It is important to note that gasoline is less dense than water, which is why it weighs less than a gallon of water (which weighs 8.34 pounds per gallon). This difference in density is one of the reasons why gasoline floats on top of water, rather than mixing with it.

So, gasoline weighs approximately 6.073 pounds per gallon, but this can vary slightly depending on the specific conditions and type of gasoline being measured.

TO know more about Gasoline here:

https://brainly.com/question/12847098#

#SPJ11

NMR active nuclei act in a way that causes them to absorb and emit electromagnetic radiation when placed inside of a magnetic field. This allows them to be used to measure the magnetic properties of the sample.

Radiation is a form of energy that is released from an atom in the form of electromagnetic waves or particles. It occurs naturally, such as from the sun, and can also be generated artificially, such as through medical or industrial processes. Radiation is all around us, and takes many forms. It can be either ionising or non-ionising radiation. Ionising radiation has enough energy to remove electrons from atoms, thus creating ions. This type of radiation is known to be hazardous and can damage living tissue, such as cells in the body. Non-ionising radiation, on the other hand, does not have enough energy to damage tissue and is therefore considered less hazardous. Examples of non-ionising radiation are radio waves, microwaves and visible light.

To learn more about radiation

https://brainly.com/question/1408043

#SPJ4

The 2,400V three-phase motor is the one in the following list that is most likely to have 15 or 18 motor leads.

We are aware that there are typically two different types of motors: AC and DC. While it comes to speed regulation, AC motors are flexible and use little power when starting. However, DC motors are popular because they are simple to install and have lower initial costs for low power units than AC motors.

"Even though people interchangeably use the two, engines and motors function differently because they employ combustion to produce energy. The motor transfers electrical energy into mechanical energy, whereas the engine translates different types of fuels into mechanical force.

To know more about Motors visit:

https://brainly.com/question/23854596

#SPJ4

Mechanical weathering is a natural process that helps to break down rocks and other materials into smaller pieces, which can then be further weathered and eroded over time.

Mechanical weathering is the process by which rocks and other materials are broken down into smaller pieces by physical means. This can occur through a variety of processes, such as freezing and thawing, abrasion, and plant root growth.

For kids, mechanical weathering can be explained as the way rocks and other materials get broken into smaller pieces by different physical forces. For example, when water gets into the cracks of rocks and freezes, it expands and makes the crack bigger. This can happen over and over again until the rock eventually breaks into smaller pieces. Other physical forces, like wind, can also cause rocks to rub against each other and break into smaller pieces. Plant roots can also grow into the cracks of rocks and push them apart, causing them to break into smaller pieces.

For such more questions on Mechanical weathering

https://brainly.com/question/4535762

#SPJ4

The term "electric boogaloo" originated from the 1984 movie "Breakin' 2: Electric Boogaloo."

The movie is a sequel to the 1984 film "Breakin'" and features street dancers battling a developer who wants to tear down their community center.

The term "electric boogaloo" has since been used to refer to a sequel or a continuation of something, often in a humorous or satirical way. For example, someone might say "The Hangover 2: Electric Boogaloo" to refer to the sequel of the movie "The Hangover." It is often used in internet memes and on social media as a way to poke fun at sequels or continuations of events.

Since the release of the movie, the phrase "Electric Boogaloo" has been used in various ways in popular culture, including as a humorous way to indicate a sequel, a way to mock or criticize a sequel or follow-up, or simply as a way to add emphasis to a statement.

To know more about electric boogaloo here:

https://brainly.com/question/28932217#

#SPJ11

Answer:

For the Comet JT2023, sketching the orbit and positions of the comet and the Sun will help in understanding better its characteristics. The eccentricity of its orbit is e = 0.99920 and its aphelion distance ra = 2,799 UA.

Using the formula for the semi-major axis of an ellipse with given eccentricity and aphelion, a=ra(1+e)/(1-e), we can find that the semi-major axis of the comet's orbit is a = 2,820.8 UA.

Using the formula for the speed of an object in an elliptical orbit, v = (GM/a)^1/2, where G is the gravitational constant, M is the mass of the sun and a is the semi-major axis of the ellipse, we can find that the speed of the comet at its aphelion is v = 3.04 km/s.

This statement is True, a gamma ray of wavelength 1.00 × 10–8 cm has enough energy to remove an electron from a hydrogen atom.

Gamma rays are produced in the disintegration of radioactive atomic nuclei and in the decay of sure subatomic particles. The normally ordinary definitions of the gamma-ray and X-ray regions of the electromagnetic spectrum encompass a few wavelength overlap, with gamma-ray radiation having wavelengths which can be usually shorter than a few tenths of an angstrom (10−10 metre) and gamma-ray photons having energies which are extra than tens of hundreds of electron volts (eV).

There's no theoretical top limit to the energies of gamma-ray photons and no decrease limit to gamma-ray wavelengths; located energies currently expand up to 3 trillion electron volts—those extraordinarily excessive-power photons are produced in astronomical sources via currently unidentified mechanisms.

To learn more about Gamma ray visit here:

brainly.com/question/23281551

#SPJ4

Foot cellulitis is classified as "Cellulitis and acute lymphangitis of different areas of leg" by the ICD-10, which assigns the code L03.311 (L03.31).

Cases of bacterial skin infections affecting the soft tissue of the foot are categorized using this code. Cuts or abrasions, insect bites, or other skin injuries are some of the many possible causes of cellulitis, a frequent illness.

Redness, warmth, swelling, soreness, and occasionally fever are some of the symptoms.

For the purpose of proper record-keeping, invoicing, and payment, medical conditions must be coded correctly. To guarantee a precise diagnosis and the best course of therapy, you must speak with a healthcare expert.

Learn more about the ICD-10 coding at

https://brainly.com/question/30388365

#SPJ4

Answer: Approximately 1.04 x 10^19 electrons pass through the filament of the light bulb in 2.00 seconds.

Explanation:

To calculate the number of electrons passing through a filament of a light bulb in 2.00 seconds, we can use the fact that the total charge passing through the filament is given as 1.67 C and the charge on a single electron is -1.6 x 10^-19 C.

The number of electrons passing through the filament is given by:

number of electrons = total charge / charge on a single electron

Substituting the given values, we get:

number of electrons = 1.67 C / (-1.6 x 10^-19 C)

Using a calculator, we get:

number of electrons = 1.04 x 10^19 electrons

Therefore, approximately 1.04 x 10^19 electrons pass through the filament of the light bulb in 2.00 seconds.

The force experienced when the boxer moves into an oncoming punch will increased due to less time period of contact.

When a mass moves in space, it carries some momentum and the momentum is defined as per the second law of motion by Newton in the following manner,

Force = change in momentum/time of contact

Change in momentum = force x time of contact.

The time of contact will decide the amount of momentum when the force is constant.

When the boxer moves towards an oncoming punch, the force experienced is increased because the time period required for the contact is decreased to a very low level.

To learn more about force,

brainly.com/question/29268524

#SP J4

The speed of the mass when moving through the equilibrium point is 1.87 m/s. To solve for the speed of the mass when moving through the equilibrium point, we can use the conservation of energy principle in a simple harmonic motion.

Initially, the mass is displaced from the equilibrium point by 0.19 m, which means the spring is stretched. At this point, all the potential energy is stored in the spring. As the mass moves towards the equilibrium point, the potential energy is converted to kinetic energy. At the equilibrium point, the kinetic energy is maximum, and the potential energy is zero.

Using the formula for potential energy in the spring, we can calculate the initial potential energy as (1/2)kx^2, where k is the spring constant and x is the displacement from the equilibrium point. Plugging in the given values, we get:

Potential energy = (1/2)(78 N/m)(0.19 m)^2 = 1.112 Nm

All the potential energy is converted to kinetic energy at the equilibrium point. Thus, the kinetic energy of the mass is also 1.112 Nm.

Using the formula for kinetic energy, we can find the speed of the mass as: Kinetic energy = (1/2)mv^2, where m is the mass of the object and v is its velocity. Plugging in the given values, we get: 1.112 Nm = (1/2)(0.32 kg)v^2

Solving for v, we get:

v = sqrt(2 * 1.112 Nm / 0.32 kg) = 1.87 m/s

The speed of the mass when moving through the equilibrium point is 1.87 m/s.

To learn more about kinetic energy, visit here

https://brainly.com/question/26472013

#SPJ4

A capacitor linked to a battery will gather electrons on one plate and deplete the other. This creates an electric field between the plates and separates charges. Option A is the right choice.

The capacitance, battery voltage, and plate distance determine how much charge builds on each plate.

Capacitance is not stated, although plate size is. Parallel plate capacitor capacitance is directly proportional to plate area and inversely proportional to plate distance. Hence, a larger plate has more capacitance.

When the capacitor is linked to a battery, the potential difference across the plates is the same regardless of size. Capacitance determines plate charge. The larger plate will gather more charge due to its higher capacitance.

Hence, A is right (the large plate has a greater charge than the small plate).

Want to know more about capacitors visit the link which is given below;

https://brainly.com/question/17176550

#SPJ4

True - the iris, or the colored part of your eye, controls the amount of light passing through. from there, it then hits the lens. this is the clear structure inside the eye that focuses light rays onto the retina.

The iris is the colored part of the eye and it is made up of two layers of muscles. These muscles control the amount of light that passes through the pupil, which is the black dot in the center of the iris.

The iris opens and closes to allow more or less light to enter the eye. When it is bright outside, the iris closes and when it is darker outside, the iris opens.

The light that passes through the pupil then hits the lens. The lens is a transparent structure inside the eye that is curved and helps to focus the light onto the retina. The lens is flexible and can change shape to help focus the light.

This focused light is then sent to the retina, which contains light-sensitive cells called rods and cones. These cells convert the light into electrical signals, which are then sent to the brain where they are interpreted as images.

To know more about rods and cones,

https://brainly.com/question/13255224

#SPJ4

The mass of disk A is approximately 5.67 kg, the mass of disk B is approximately 3.72 kg, the mass of disk C is approximately 0.98 kg, the mass of disk D is approximately 2.53 kg.

To solve for the masses of the disks, we can use the fact that the tension in each cord is equal to the weight of the disk it supports, or:

T1 = m_A * g

T2 = m_B * g

T3 = m_C * g

T4 = m_D * g

where m_A, m_B, m_C, and m_D are the masses of disks A, B, C, and D, respectively, g is the acceleration due to gravity, and T1, T2, T3, and T4 are the tensions in the cords.

We can also use the fact that the total force on the system is equal to the force applied by the longer cord, or:

T1 + T2 + T3 + T4 = F_applied

where F_applied is the force of magnitude 86.5 N applied by the longer cord.

Using these equations, we can solve for the masses of the disks:

(a) To find the mass of disk A, we can use the equation for T1:

T1 = m_A * g

Substituting T1 = 55.6 N and g = 9.8 m/s^2, we get:

m_A = T1 / g

= 55.6 N / 9.8 m/s^2

≈ 5.67 kg

Therefore, the mass of disk A is approximately 5.67 kg.

(b) To find the mass of disk B, we can use the equation for T2:

T2 = m_B * g

Substituting T2 = 36.5 N and g = 9.8 m/s^2, we get:

m_B = T2 / g

= 36.5 N / 9.8 m/s^2

≈ 3.72 kg

Therefore, the mass of disk B is approximately 3.72 kg.

(c) To find the mass of disk C, we can use the equation for T3:

T3 = m_C * g

Substituting T3 = 9.6 N and g = 9.8 m/s^2, we get:

m_C = T3 / g

= 9.6 N / 9.8 m/s^2

≈ 0.98 kg

Therefore, the mass of disk C is approximately 0.98 kg.

(d) To find the mass of disk D, we can use the equation for T4:

T4 = m_D * g

Substituting T4 = (F_applied - T1 - T2 - T3) = (86.5 N - 55.6 N - 36.5 N - 9.6 N) = 24.8 N and g = 9.8 m/s^2, we get:

m_D = T4 / g

= 24.8 N / 9.8 m/s^2

≈ 2.53 kg

Therefore, the mass of disk D is approximately 2.53 kg.

Learn more about tension here:

https://brainly.com/question/11348644

#SPJ4

The responding variable in this experiment on adding salt to bottles of water is C. The time it takes for the water to boil.

The responding variable in this experiment is the time it takes for the water to boil, which is being measured and recorded by the scientist. This variable is dependent on the independent variable, which in this case is the amount of salt added to each bottle of water.

The scientist is manipulating the independent variable (the amount of salt added) to observe the effect it has on the responding variable (the time it takes for the water to boil).

Find out more on responding variable at https://brainly.com/question/28417576

#SPJ1

The largest spring tides happen when the moon is close to perigee and the sun is close to perihelion.

The "heaping" motion that results from the horizontal water flow towards two areas of the planet that represent points of maximal attraction of combined solar and lunar gravitational forces causes high tides in the oceans.

The highest astrological tide (HAT) or lowest astrological tide (LAT) levels that can be anticipated to occur under typical meteorological conditions and any confluence of astronomical conditions, respectively, are given.

To know more about perigee visit:

https://brainly.com/question/14704879

#SPJ1

Assume that the canoe's velocity relative to the Earth is represented by vector v and the current's velocity relative to the Earth is represented by vector u. The canoe's velocity relative to the river, represented by vector v r, is then given by vector subtraction of v and u:

v r = v - u

The length of the vector v r, which is given by the Pythagorean theorem, is the magnitude of the canoe's velocity relative to the river:

sqrt((v x - u x)² + (v y - u y)²) |v r|

where v x and v y represent v's x- and y-components, and u x and u y represent u's x- and y-components.

The direction of the velocity of the canoe relative to the river is the angle that v_r makes with the x-axis. This angle is given by:

theta = atan2(v_y - u_y, v_x - u_x)

where atan2 is a function that returns the angle between the positive x-axis and the point (v_x - u_x, v_y - u_y).

Therefore, the magnitude and direction of the velocity of the canoe relative to the river can be found using the above equations.

To Learn More About velocity click

brainly.com/question/18084516

#SPJ4

To convert joules (J) to electronvolts (eV), you can use the conversion factor of 1 eV = [tex]1.60218 * 10^-^{19}[/tex]J. This means that one electronvolt is equivalent to the amount of energy gained by an electron when it moves through a potential difference of one volt.

In physics, an electronvolt is the measure of an amount of kinetic energy gained by a single electron accelerating from rest through an electric potential difference of one volt in vacuum.

To convert joules to electronvolts, you can use the following formula:

Energy in eV = (Energy in J) / [tex](1.60218 * 10^-^{19})[/tex]

For example, if you have an energy value of 1.5 J, you can convert it to electronvolts using the formula:

Energy in eV = 1.5 J /  [tex](1.60218 * 10^-^{19})[/tex] ≈ 9.35 x[tex]10^{18}[/tex] eV

Therefore, 1.5 J is equivalent to approximately 9.35 x [tex]10^{18}[/tex] electronvolts.

For such more questions on Electronvolts

https://brainly.com/question/30145077

#SPJ4

(a) When the bucket is being pulled up at a constant speed, the tension in the rope must be equal to the weight of the bucket and the water. The weight of the bucket and water is given by:

[tex]w = m*g[/tex]

where m is the mass of the bucket and water (6 kg in this case), and g is the acceleration due to gravity [tex](9.8 m/s^2).[/tex] So,

[tex]w = 6 kg * 9.8 m/s^2 = 58.8 N[/tex]

Therefore, the tension in the rope must also be 58.8 N.

(b) When the bucket has an upward constant acceleration of [tex]3 m/s^2,[/tex] the tension in the rope must be greater than the weight of the bucket and water, in order to provide the additional force needed to accelerate the bucket upwards. The tension in the rope can be calculated using the equation:

[tex]T - w = m*a[/tex]

where T is the tension in the rope, w is the weight of the bucket and water (58.8 N), m is the mass of the bucket and water (6 kg), and a is the acceleration of the bucket (3 m/s^2). Substituting these values, we get:

[tex]T - 58.8 N = 6 kg * 3 m/s^2\\T - 58.8 N = 18.0 N\\T = 76.8 N[/tex]

Therefore, the tension in the rope when the bucket has an upward constant acceleration of[tex]3 m/s^2[/tex] is 76.8 N.

(c) When the bucket has a downward constant acceleration of 3 m/s^2, the tension in the rope must be less than the weight of the bucket and water, in order to balance out the force of gravity pulling the bucket downwards. The tension in the rope can be calculated using the same equation as before:

[tex]T - w = m*a[/tex]

where T is the tension in the rope, w is the weight of the bucket and water (58.8 N), m is the mass of the bucket and water (6 kg), and a is the acceleration of the bucket (-3 m/s^2) because it is now going downwards. Substituting these values, we get:

[tex]T - 58.8 N = 6 kg * (-3 m/s^2)\\T - 58.8 N = -18.0 N\\T = 40.8 N[/tex]

Therefore, the tension in the rope when the bucket has a downward constant acceleration of [tex]3 m/s^2[/tex] is 40.8 N.

Learn more about tension, here:

https://brainly.com/question/30033702

#SPJ1

If a person visits an exercise facility, buys a new piece of fitness or sporting equipment, or just starts planning to be active, they are likely in the "Contemplation" stage of change for physical activity.

What are the Five stages?

The five stages of change for physical activity are:

• Precontemplation: In this stage, the person is not yet considering a change in their physical activity behaviour.

• Contemplation: In this stage, the person is starting to think about making a change and may be weighing the pros and cons of becoming more active.

• Preparation: In this stage, the person has decided to make a change and is taking steps to start an exercise program, such as setting goals and making a plan.

• Action: In this stage, the person has actually started to incorporate physical activity into their routine.

• Maintenance: In this stage, the person has successfully integrated physical activity into their lifestyle and is maintaining the change over time.

Based on the information provided, the person visiting an exercise facility, buying new fitness equipment, or starting to plan to be active is likely in the Contemplation stage, as they are considering making a change in their physical activity behaviour.

To know more about stages of physical activity, Check out:

https://brainly.com/question/15604052

#SPJ4

.

10mL equals two teaspoons (2tsp). A tablespoon is 3 instances bigger than a teaspoon and three teaspoons identical one tablespoon (1Tbsp or 1Tb). One tablespoon also equals 15mL.

A teaspoon is a small kitchen utensil used for measuring small quantities of ingredients such as sugar, salt, spices, or baking powder. It is also used for stirring or mixing liquids and other ingredients. A teaspoon is typically a small, narrow, and elongated spoon with a shallow bowl and a long handle. It can hold about 5 milliliters (mL) or approximately one-third of a tablespoon.

The teaspoon is commonly used in recipes and cooking as a standard unit of measurement for small quantities of ingredients. It is also used in medicine to measure liquid medications or for administering oral medication. Teaspoons come in various materials such as stainless steel, plastic, or wood. They may be sold individually or in sets.

To learn more about Teaspoons visit here:

brainly.com/question/25928464

#SPJ4

Complete Question: -

How much is 10 mL in teaspoons or tablespoons?

Increases in ghrelin increase hunger, whereas increases in leptin decrease hunger, this is option A, as ghrelin is a hormone produced in the stomach that stimulates appetite and increases food intake.

The body has a complex system for regulating hunger and appetite, and two of the key hormones involved in this process are ghrelin and leptin, ghrelin is produced in the stomach and is released in response to an empty stomach, while leptin is produced by fat cells and acts as a signal to the brain that the body has enough energy stores.

Hence, Increases in ghrelin increase hunger, whereas increases in leptin decrease hunger; this is option A.

Learn more about hunger and hormones here.

https://brainly.com/question/28171995

#SPJ1

The question is incomplete, the complete question is below,

a. ghrelin; leptin

b. blood glucose; melanin

c. thyroxin; blood glucose

The fact that we always see the same face of the moon tells us that the moon is tidally locked to Earth.
This means that the same side of the moon is always facing the Earth, while the opposite side is never seen. This is because of the gravitational pull of the Earth, which keeps the same side of the moon in its view.

As the moon orbits around the Earth, the Earth's gravity slowly pulls the moon's rotation and orbit into sync so that the same side of it is always facing the Earth. This means that the same side of the moon is lit by the Sun and visible to us here on Earth. This phenomenon is known as tidal locking.

For more questions like Moon click the link below:

https://brainly.com/question/18367769

#SPJ4

The gauge pressure of the air in the tank is 1349.3 Pa in an inclined manometer.

An inclined manometer is a device that measures the pressure of a gas by comparing it to the pressure of a liquid in a column that is inclined at a certain angle. In this case, the manometer is connected to a tank of air, and the column of liquid is inclined at an angle of 45 degrees from the horizontal line. To determine the gauge pressure of the air in the tank, we need to use the equation:

ΔP = ρgh

where ΔP is the pressure difference, ρ is the density of the fluid (in this case, water), g is the acceleration due to gravity, and h is the height difference between the two fluid levels.

In the manometer, the fluid level on one side is at a height of 6 cm and the other side is at an angle of 45 degrees, with pressure readings of 501 Pa and 416 Pa, respectively. We can use trigonometry to find the vertical height difference between the two fluid levels:

h = [tex]6 cm * sin(45) = 4.24 cm[/tex] = 0.0424 m

Next, we can calculate the pressure difference between the two sides of the manometer using the equation above:

ΔP = [tex](1000 kg/m^3 - 0.225 kg/m^3) * 9.81 m/s^2 * 0.0424 m[/tex] = 933.3 Pa

Finally, we can calculate the gauge pressure of the air in the tank by adding the pressure difference to the lower pressure reading:

P_gauge = 416 Pa + 933.3 Pa = 1349.3 Pa

Learn more about gauge pressure here:

https://brainly.com/question/19573649

#SPJ4

The wave nature of matter is generally not significant for bullets, which are macroscopic objects composed of many particles.

The wave-particle duality of matter is a fundamental property of subatomic particles, such as electrons and photons, and is observed at the quantum level. For larger objects, including bullets, classical mechanics provides a sufficient framework for describing their behavior. However, in some cases, such as the diffraction of electrons or neutrons passing through small openings, the wave nature of matter can have practical applications. In general, though, the wave nature of matter is not a significant factor in the behavior of bullets.

Learn more about wave nature:

brainly.com/question/29023881

#SPJ4

A plucked guitar string would vibrate for a shorter time if the instrument had no sounding board.

The sounding board, or soundboard, is a large, flat panel that amplifies the sound of the strings by vibrating along with them. This vibration increases the overall volume of the sound and also sustains the vibration of the strings for a longer period of time.

When a guitar string is plucked, it vibrates and creates sound waves that travel through the air and into the listener's ear. The sounding board helps to amplify these sound waves, making the sound of the string louder and more resonant. The sounding board also helps to sustain the vibration of the string by reflecting and reinforcing the sound waves back into the string, keeping it vibrating for a longer period of time.

Without a sounding board, the string would vibrate for a shorter time because the sound waves generated by the string would not be reinforced and amplified in the same way. The vibration of the string would be damped more quickly, causing the sound to decay more quickly and the string to vibrate for a shorter period of time.

To know more about musical instruments, visit:

brainly.com/question/16191430

#SPJ4

a. The sound's wavelength is 20 cm. and b) 40 cm should be the next distance of maximum intensity.

A sound wave is the pattern of disruption brought on by the movement of energy moving through a medium as it propagates away from the source of the sound (such as air, water, or any other liquid or solid matter). Pressure waves are produced when an object vibrates, such as a ringing phone, and these waves are known as sound waves.

a. Calculating the next distance and wavelength:

The wavelength ought to be : Since

(nλ + λ/2) - nλ = 30-20

So,

λ/2 = 10

λ = 20 cm

b. The distance now ought to be

It is necessary to raise the path difference by (n+1).

Additionally, the distance should grow by /2 from the intensity zero point

So,

= 30 + λ/2

= 30 + 20/2

=30+10

=40 cm

Learn more about sound waves Visit: brainly.com/question/1199084

#SPJ4

Correct Question:

Two loudspeakers emit sound waves along the x-axis. The sound has maximum intensity when the speakers are 20 cm apart. The sound intensity decreases as the distance between the speakers is increased, reaching zero at a separation of 30 cm.

a. What is the wavelength of the sound?

b. If the distance between the speakers continues to increase, at what separation will the sound intensity again be a maximum?

1. The ball was struck horizontally with a speed of 30.0 m/s.

2. The ball hit the court at a horizontal distance of 20.0 m from the racket.

3. The initial height of the ball when it left the racket was 2.2 m above the court.

4. The time taken for the ball to hit the ground was 2.12 seconds.

Speed is a scalar quantity that represents the magnitude of an object's velocity. It is defined as the rate of change of an object's position with respect to time. Speed is a measure of how fast an object is moving, and it is expressed in units of distance per unit of time, such as meters per second (m/s) or kilometers per hour (km/h).

Speed is different from velocity in that velocity is a vector quantity that also includes information about the direction of an object's motion. So, an object's speed only gives information about how fast it is moving, while its velocity gives information about both the magnitude and direction of its motion.

For example, a car moving at a constant speed of 60 km/h has a constant velocity, but its speed is constant, while its velocity is changing if the direction of motion changes.

Equations of motion under constant acceleration (in this case, acceleration due to gravity) can be used to solve;

The height of the ball when it leaves the racket and the time it takes for the ball to hit the ground.

The vertical position of the ball can be described by the equation:

[tex]h = h0 + v0t - (1/2)gt^2[/tex]

where h0 is the initial height of the ball when it leaves the racket, v0 is the initial vertical velocity of the ball, t is the time elapsed, and g is the acceleration due to gravity[tex](g = 9.8 m/s^2)[/tex].

Since the ball is departing horizontally, the initial vertical velocity is zero (v0 = 0). the time t  has to be solved using the horizontal position of the ball:

[tex]d = v0t = 30.0 m/s * t[/tex]

[tex]t = d / v0 = 20.0 m / 30.0 m/s = 2/3 s[/tex]

The time is found, plug it back into the equation for the vertical position:

[tex]h = h0 - (1/2)gt^2 = h0 - (1/2)(9.8 m/s^2)(2/3 s)^2[/tex]

Since the initial height of the ball is not given, set h0 = 0 for simplicity. Then,

[tex]h = - (1/2)(9.8 m/s^2)(2/3 s)^2 = - 4.9 m/s^2 (2/3 s)^2 = - 4.9 * (4/9) = - 2.2 m[/tex]

So, the ball is 2.2 m above the court when it leaves the racket.

To find the time taken for the ball to hit the ground, solve the time when the vertical position of the ball is equal to zero:

[tex]0 = h0 - (1/2)gt^2[/tex]

[tex]t = sqrt(2h0 / g) = sqrt(2 * (-2.2 m) / 9.8 m/s^2) = sqrt(44.4 / 9.8) = sqrt(4.5) s = 2.12 s[/tex]

So, it took 2.12 seconds for the ball to hit the ground.

To know more about Speed, visit:

https://brainly.com/question/6504879

#SPJ4

Answer:

Higher winds mean the possibility of severe weather.

Explanation:

High winds blow low pressure systems into our area, giving us bad weather.