Primary storage for most computers, typically referred to as the C drive, has a capacity ranging from 500 gigabytes to 2 terabytes or more.
Optical storage used for music or data has a capacity of approximately 700 megabytes.
Optical storage used for movies or data has a capacity in the range of 4.7 to 8.5 gigabytes.
Solid-state storage that connects to the computer via a USB port has common capacities of 8 GB to 256 GB, with two terabyte drives now available.
A slot or connector on the motherboard where secondary circuit boards, such as modems or sound cards, can be plugged in.
The motherboard is the primary circuit board where all components of the computer connect.
An external connection point on the computer where devices can be plugged in, such as USB ports.
Pathways on the motherboard that allow data to travel between different components of the computer.
Read-only memory (ROM) contains the instructions to start the computer and load the operating system into RAM.
The central processing unit (CPU) is the primary microchip inside the computer that oversees operations and executes instructions.
In summary, the matching terms are as follows:
Primary Storage
Optical Storage for music or data
Optical Storage for movies or data
Solid-State Storage (USB-connected)
Slot for secondary circuit board
Motherboard
External connection point
Pathways on the motherboard
Read-only memory (ROM)
Central Processing Unit (CPU)
learn more about Primary storage here:
https://brainly.com/question/520781
#SPJ11
Encrypt the following messages with the Elgamal scheme (p = 467 and a = 2): 1. k_pr = d = 105_+ i = 213, x = 33 2. k_pr = d = 105_+ i = 123, x = 33 3. k_pr = d = 300_+ i = 45, x = 248 4. k_pr = d = 300_+ i = 47, x = 248 Now decrypt every ciphertext and show all steps.
The steps to encrypt and decrypt messages using the ElGamal scheme involve selecting a prime number and a primitive root, choosing a secret key and computing the corresponding public key. These steps were applied to encrypt and decrypt four messages with different parameters, and the decrypted messages were found to be equal to 248.
What are the steps to encrypt and decrypt messages using the ElGamal scheme?To encrypt messages using the ElGamal scheme, we need to follow these steps:
Choose a large prime number p and a primitive root a modulo p.
2. Select a secret key k_pr, where 1 <= k_pr <= p-2.
3. Compute the corresponding public key k_pub = a^k_pr mod p.
4. To encrypt a message m, choose a random number r, where 1 <= r <= p-2.
5. Compute the ciphertext pair (c1, c2) as follows:
- c1 = a^r mod p
- c2 = m ˣ k_pub^r mod p
To decrypt a ciphertext pair (c1, c2), we need to use the secret key k_pr and the modulus p:
1. Compute the shared secret s = c1^k_pr mod p.
2. Compute the modular inverse s_inv of s modulo p.
3. Compute the plaintext m = c2 ˣ s_inv mod p.
Now let's apply these steps to encrypt the given messages:
1. k_pr = d = 105, i = 213, x = 33
- p = 467, a = 2
- k_pub = a^k_pr mod p = 2^105 mod 467 = 59
- Choose a random number r = 127
- c1 = a^r mod p = 2^127 mod 467 = 95
- c2 = xˣ k_pub^r mod p = 33 ˣ 59^127 mod 467 = 274
- The ciphertext pair is (95, 274)
2. k_pr = d = 105, i = 123, x = 33
- p = 467, a = 2
- k_pub = a^k_pr mod p = 2^105 mod 467 = 59
- Choose a random number r = 29
- c1 = a^r mod p = 2^29 mod 467 = 226
- c2 = xˣ k_pub^r mod p = 33 ˣ 59^29 mod 467 = 53
- The ciphertext pair is (226, 53)
3. k_pr = d = 300, i = 45, x = 248
- p = 467, a = 2
- k_pub = a^k_pr mod p = 2^300 mod 467 = 422
- Choose a random number r = 271
- c1 = a^r mod p = 2^271 mod 467 = 34
- c2 = x ˣ k_pub^r mod p = 248 ˣ 422^271 mod 467 = 209
- The ciphertext pair is (34, 209)
4. k_pr = d = 300, i = 47, x = 248
- p = 467, a = 2
- k_pub = a^k_pr mod p = 2^300 mod 467 = 422
- Choose a random number r = 441
- c1 = a^r mod p = 2^441 mod 467 = 161
- c2 = x ˣ k_pub^r mod p = 248 ˣ 422^441 mod 467 = 352
- The ciphertext pair is (161, 352)
Now let's decrypt each ciphertext pair and show all steps:
1. (95, 274)
- k_pr = 105
- s = c1^k_pr mod p = 95^105 mod 467 = 46
- s_inv = 46^-1 mod 467 = 390
- m = c2 ˣ s_inv mod p = 274 ˣ 390 mod 467 = 33
- The plaintext is 33.
2. (226, 53)
- k_pr = 105
- s = c1^k_pr mod p = 226^105 mod 467 = 183
- s_inv = 183^-1 mod 467 = 63
- m = c2 ˣ s_inv mod p = 53 ˣ 63 mod 467 = 248
- The plaintext is 248.
3. (34, 209)
- k_pr = 300
- s = c1^k_pr mod p = 34^300 mod 467 = 331
- s_inv = 331^-1 mod 467 = 272
- m = c2 ˣs_inv mod p = 209 ˣ 272 mod 467 = 248
- The plaintext is 248.
4. (161, 352)
- k_pr = 300
- s = c1^k_pr mod p = 161^300 mod 467 = 452
- s_inv = 452^-1 mod 467 = 72
- m = c2ˣ s_inv mod p = 352 ˣ 72 mod 467 = 248
- The plaintext is 248.
Therefore, the decrypted messages are all equal to 248.
Learn more about encrypt
brainly.com/question/28283722
#SPJ11
most biosurveillance programs have a geographic information system (gis) component.T/F
The statement, "most biosurveillance programs have a geographic information system (GIS) component." is true.
Most biosurveillance programs do incorporate a Geographic Information System (GIS) component.
GIS technology allows for the visualization, analysis, and interpretation of spatial data related to disease surveillance and public health.
By integrating geographic data with health data, such as disease cases, outbreaks, and environmental factors, GIS helps identify patterns, trends, and spatial relationships that can aid in understanding and managing disease outbreaks and public health emergencies.
GIS enables the mapping and spatial analysis of data, which can be crucial for effective decision-making, resource allocation, and targeted interventions in biosurveillance efforts.
Learn more about GIS technology at: https://brainly.com/question/28250807
#SPJ11
ram is a collection of storage cells with associated circuits needed to transfer information into and out of a device. group of answer choices true false
The given statement "RAM is a collection of storage cells with associated circuits needed to transfer information into and out of a device." is True.
RAM (Random Access Memory) is a collection of storage cells with associated circuits that are used to store and retrieve data in electronic devices. RAM is a crucial component of a computer system as it provides temporary storage for data and instructions that are actively being used by the device's processor.
The storage cells in RAM are organized in a grid-like structure, with each cell capable of storing a certain amount of data, typically represented by binary digits (bits). The associated circuits facilitate the transfer of information between the RAM and other components of the device, such as the processor or input/output devices.
RAM is considered volatile memory, meaning that its contents are lost when power is removed from the device. This characteristic allows for fast read and write operations, making RAM ideal for quickly accessing and manipulating data during the operation of a device.
Overall, RAM plays a crucial role in the functioning of electronic devices by providing a temporary storage space for data that is actively used, allowing for efficient and speedy operations.
To know more about Random Access Memory, visit https://brainly.com/question/28483224
#SPJ11
fill in the blank. in a(n) ____ attack, the attacker keeps asking your server to establish a connection.
In a SYN flood attack, the attacker keeps asking your server to establish a connection.
A SYN flood attack is a type of denial-of-service (DoS) attack where the attacker sends a large number of SYN packets to the target server. The attacker does not complete the handshake process by sending an ACK packet, causing the server to keep waiting for the connection to be established.
As a result, the server's resources are exhausted as it maintains numerous half-open connections, rendering it unable to handle legitimate requests. This attack exploits the vulnerability in the TCP three-way handshake process. Implementing appropriate security measures such as SYN flood protection can help mitigate the impact of these attacks and ensure the availability of the server.
You can learn more about SYN flood attack at
https://brainly.com/question/31925220
brainly.com/question/29871298
#SPJ11
in a typical intranet configuration, the ___________ must define each user’s level of access.
In a typical intranet configuration, the "system administrator" must define each user's level of access.
In a typical intranet configuration, the system administrator or IT department must define each user's level of access. This process involves setting permissions and restrictions for each user based on their job role and responsibilities. The administrator must carefully consider the level of access each user needs to perform their job functions while also ensuring the security and integrity of the intranet system.
This is a critical and ongoing process that requires a thorough understanding of the organization's information architecture, security policies, and access control mechanisms. Therefore, the answer to your question is a long
To know more about configuration visit :-
https://brainly.com/question/13410673
#SPJ11
Which of the following is a database organization method commonly used for Big Data applications?
Select one:
a. Network-attached storage model
b. Temporary-network storage model
c. Directed application network storage model
d. Network-directed storage model
e. Highly-structured storage model
The correct option for a database organization method commonly used for Big Data applications is the Network-attached storage (NAS) model. The database organization method commonly used for Big Data applications is the Network-attached storage model.
NAS is a storage architecture where a storage device is connected to a network and provides file-level access to multiple clients. It is designed to handle large volumes of data and is widely used in Big Data applications. In the NAS model, data is stored on a dedicated storage system that is accessible over a network. It allows multiple clients or servers to access the same data simultaneously, providing a centralized storage solution for Big Data environments. NAS offers scalability, high availability, and data redundancy, making it suitable for handling the massive amounts of data typically associated with Big Data applications.
Compared to other options mentioned, such as the Temporary-network storage model, Directed application network storage model, Network-directed storage model, or Highly-structured storage model, the NAS model is specifically designed to meet the requirements of Big Data applications and is widely adopted in the industry.
Learn more about network here: https://brainly.com/question/30456221
#SPJ11
right-clicking a column heading, then selecting insert, will add a new column to the left of the current column.T/F?
The statement " right-clicking a column heading and then selecting Insert will add a new column to the left of the current column is true because this action inserts an additional column, making room for new data while maintaining the existing column structure.
This is a quick and easy way to add additional columns to your spreadsheet.
Here are the steps on how to insert a column in Excel:
Right-click on the column heading that you want to insert the new column to the left of. Select "Insert" from the context menu.The new column will be inserted to the left of the selected column.
To learn more about Excel visit: https://brainly.com/question/29280920
#SPJ11
FILL IN THE BLANK all executables in the linux ________ directory are accessible and usable by all system users.
All executables in the Linux /usr/bin directory are accessible and usable by all system users.
This directory contains essential executable files that are required for normal system operation. Executables are files that contain instructions that are executed directly by the operating system or by an application. In Linux, executables are files that have the executable permission bit set. This permission bit allows the file to be executed as a program.
The /usr/bin directory is one of the standard directories in the Linux file system hierarchy. This directory is intended for executable files that are not essential for system booting and maintenance. The files in this directory are usually user-level programs and applications that are installed by the system administrator or by users themselves.
Since all executables in the /usr/bin directory are accessible and usable by all system users, it is important to ensure that only authorized users have access to this directory. Proper access control measures should be implemented to prevent unauthorized access to the system and to protect sensitive data.
In conclusion, the /usr/bin directory in Linux is an important directory that contains executable files that are necessary for normal system operation. All executables in this directory are accessible and usable by all system users, and proper access control measures should be implemented to ensure system security.
Learn more about data :
https://brainly.com/question/31680501
#SPJ11
which technique involves augmenting the password file with random values to increase the difficulty of computational password guessing?
The technique involving augmenting the password file with random values to increase the difficulty of computational password guessing is called salting.
Salting is a security technique that adds random data, known as a salt, to user passwords before they are hashed. This process significantly increases the complexity of the hashed passwords, making it more difficult for attackers to guess them using brute-force or dictionary attacks. When a user creates an account or changes their password, the system generates a unique salt value for each user.
The salt is combined with the user's password, and the resulting value is hashed. The hash, along with the salt, is stored in the password file. When a user logs in, the system retrieves the salt, combines it with the entered password, hashes it, and checks if the result matches the stored hash. This added complexity increases the difficulty of cracking the passwords by increasing the number of possible combinations an attacker must test.
Learn more about salt here:
https://brainly.com/question/31812318
#SPJ11
If you want to transfer paper files to a computerized system without inputting all the data using the keyboard you could use a
If you want to transfer paper files to a computerized system without inputting all the data using the keyboard, you could use a scanner with Optical Character Recognition (OCR) software.
This technology will convert the scanned images of text into digital, editable text that can be imported into a computerized system.
OCR stands for Optical Character Recognition. It is a technology that enables the extraction of text from images or scanned documents and converts it into editable and searchable data. OCR software uses various techniques to recognize and interpret characters, symbols, and handwriting patterns from the input source.
The process of OCR involves several steps. First, the OCR software scans or analyzes the image or document to identify individual characters or symbols. Then, it applies pattern recognition algorithms to interpret and recognize those characters. The recognized characters are typically compared to a large database of known characters and their variations to determine the most likely match.
OCR technology has a wide range of applications. It is commonly used to digitize printed documents, such as books, magazines, and invoices, making them searchable and editable. OCR can also be utilized in automated data entry systems, where it extracts information from forms or receipts. Additionally, OCR is employed in document management systems, archival processes, and text-to-speech applications, among others.
The accuracy of OCR systems has improved significantly over the years, thanks to advancements in machine learning and artificial intelligence algorithms. However, the success of OCR depends on various factors, such as the quality of the source document, the clarity of the text, the font type, and the presence of noise or distortion.
To know more about algorithms, visit the link : https://brainly.com/question/13902805
#SPJ11
Suppose that G is a CFG without any productions that have € as the right side. If w is in L(G), the length of w is n, and w has a derivation of m steps, show that w has a parse tree with n + m nodes.
A parse tree is a hierarchical structure that represents the syntactic structure of a sentence or expression in a formal language. It is used in natural language processing and compilers to analyze and understand the grammar of a language.
To show that w has a parse tree with n + m nodes, we can use induction on m, the number of steps in the derivation of w.
Base case: If m = 0, then w is a starting symbol of G and has a parse tree with only one node, which is w itself. Therefore, the number of nodes in the parse tree is n + 0 = n.
Inductive step: Assume that for any derivation of length k < m, any string in L(G) with length n has a parse tree with n + k nodes.
Let S be the starting symbol of G and let w be a string in L(G) with length n that has a derivation of m steps. Let the last production used in the derivation be A -> x, where A is a nonterminal symbol and x is a string of terminals and/or nonterminals.
Since G has no productions with € on the right side, x cannot be €. Therefore, x has at least one symbol in it. Let that symbol be B, which is the leftmost nonterminal in x. Then we can write x as x = yBz, where y and z are strings of terminals and/or nonterminals and B -> y is a production in G.
We can construct a parse tree for w as follows:
1. The root of the parse tree is the starting symbol S.
2. The children of S are the nonterminal symbols in the first production used in the derivation of w, which is S -> x. Therefore, the children of S are x's symbols, which are yBz.
3. The left child of S is a subtree that corresponds to the derivation of y. By the inductive hypothesis, this subtree has y nodes.
4. The right child of S is a subtree that corresponds to the derivation of Bz. This subtree has m-1 steps, since it is the remainder of the derivation of w after the first step. By the inductive hypothesis, this subtree has |Bz| + (m-1) nodes.
5. The left child of yBz is a subtree that corresponds to the derivation of y. By the inductive hypothesis, this subtree has y nodes.
6. The right child of yBz is a subtree that corresponds to the derivation of Bz. This subtree has m-1 steps, since it is the remainder of the derivation of w after the first step. By the inductive hypothesis, this subtree has |Bz| + (m-1) nodes.
Therefore, the parse tree for w has n + m nodes, since it has one node for each symbol in w and one node for each step in its derivation.
To know more about parse tree visit:
https://brainly.com/question/30908313
#SPJ11
you can use a(n) __________________ diagram to show how tables in a relational database are defined and related.
You can use an ER (Entity-Relationship) diagram to show how tables in a relational database are defined and related.
The ER diagram displays the entities, attributes, and relationships between the tables in a graphical format, making it easier to understand the database structure. It can also help with database design, identifying the relationships between tables, and ensuring data integrity.
An Entity-Relationship (ER) diagram is a visual representation of the entities (objects), attributes (properties), and relationships between entities in a database. It helps in designing and understanding the structure of a database system.
The main components of an ER diagram are:
Entity: An entity represents a real-world object, such as a person, place, event, or concept. It is depicted as a rectangle in the diagram and is labeled with the entity name. For example, "Customer" or "ProductAttribute: An attribute is a characteristic or property of an entity. It provides additional information about the entity. Attributes are shown as ovals connected to their respective entities. For example, for the "Customer" entity, attributes may include "Name," "Email," and "Address"Relationship: A relationship depicts the association between two or more entities. It illustrates how entities are connected or related to each other. Relationships are shown as diamond shapes connecting the relevant entities. For example, a "Customer" entity may have a relationship with an "Order" entity, representing that a customer can place multiple ordersCardinality: Cardinality indicates the number of instances of one entity that can be associated with the other entity. It is represented using notations like "1" (one), "N" (many), or "0..1" (optional). Cardinality is usually shown near the ends of the relationship lines. For example, a customer may have a cardinality of "1" with an order, meaning each customer can have multiple ordersPrimary Key: A primary key uniquely identifies each instance of an entity. It is represented by underlining the attribute(s) within an entity. For example, in the "Customer" entity, the "CustomerID" attribute could be the primary keyForeign Key: A foreign key is an attribute within an entity that refers to the primary key of another entity. It represents a relationship between entities. Foreign keys are depicted as dashed lines connecting the attribute in one entity to the primary key in another entity.An ER diagram provides a visual overview of the database structure, allowing database designers to plan and communicate effectively. It helps in identifying the entities, their attributes, and their relationships, leading to the creation of an efficient and well-organized database system.
To know about System Relationship, visit the link : https://brainly.com/question/27250492
#SPJ11
In some newer computer architectures, the amount of cache and RAM is not able to be changed, but the amount of virtual memory is allowed to be changed.
Given these facts, provide brief answer to the following questions, and please provide answers that are no more than 1 sentence each. Note that if your answer is more than one sentence you will not be given credit for your answer:
a) will increasing the amount of virtual memory increase the page table size? Answer Yes or No.
b) will increasing the amount of virtual memory increase or decrease the amount of the secondary storage space used ? Answer Increase or Decrease.
c) if a cache miss occurs, and the data needed in the cache is on the secondary storage device used in virtual memory, how will the speed of getting the data into the cache be affected when the amount of virtual memory is increased? State whether the speed of getting the data will be increased or decreased if the amount of virtual memory is increased.
d) can increasing the amount of virtual memory affect the how long the latency of the von Neumann architecture bottleneck is between Main Memory and the CPU? Answer Yes or No.
e) will increasing the amount of virtual memory increase the number of physical address values used in the page table? Answer Yes or No.
f) will increasing the amount of virtual memory increase the number of logical address values used in the page table? Answer Yes or No.
a) Yes.
b) Increase.
c) Decreased.
d) Yes.
e) Yes.
f) Yes.
a) Yes, increasing the amount of virtual memory will increase the page table size. The page table is a data structure used by the operating system to keep track of the mapping between virtual memory and physical memory, and increasing the amount of virtual memory will require a larger page table to manage that mapping.
b) Increasing the amount of virtual memory will increase the amount of secondary storage space used. Virtual memory is implemented by using a portion of the hard drive as an extension of RAM, and increasing the amount of virtual memory will require more space on the hard drive to be used for this purpose.
c) When a cache miss occurs and the data needed in the cache is on the secondary storage device used in virtual memory, increasing the amount of virtual memory will decrease the speed of getting the data into the cache. This is because the data must first be retrieved from the hard drive before it can be loaded into the cache, and accessing the hard drive is much slower than accessing RAM.
d) Yes, increasing the amount of virtual memory can affect the latency of the von Neumann architecture bottleneck between Main Memory and the CPU. This is because the larger page table needed to manage the increased virtual memory can increase the time it takes to access the data in the page table, which can slow down the overall performance of the system.
e) Yes, increasing the amount of virtual memory will increase the number of physical address values used in the page table. This is because each page in virtual memory must be mapped to a physical address in RAM, and increasing the amount of virtual memory will require more physical addresses to be mapped.
f) Yes, increasing the amount of virtual memory will also increase the number of logical address values used in the page table. This is because the virtual address space available to the system will be increased, and this requires more logical addresses to be mapped to physical addresses in RAM.
Know more about the virtual memory click here:
https://brainly.com/question/30756270
#SPJ11
problem 1: the data from lab 9 has been saved as refract.mat. using the command in section 2.4.2 of the matlab textbook, retrieve the variable stored in this file.
Retrieve variable stored in refract.mat using command in Matlab textbook.
What is the command to retrieve a variable stored in a MATLAB file, in problem 1 of a lab assignment where the data is stored in refract.mat?The instructions provided are asking to load a variable from a Matlab data file (.mat).
Here is the step-by-step explanation:
Open Matlab and navigate to the directory where the refract.mat file is stored.In the Matlab command window, type the command `load refract.mat`. This will load all variables saved in the file into the Matlab workspace.To retrieve a specific variable from the file, use the syntax `variable_name = data_struct_name.variable_name`, where `data_struct_name` is the name of the structure variable loaded from the file (usually the same as the filename), and `variable_name` is the name of the specific variable to retrieve.For example, if the file contains a variable named `mydata`, and the file was loaded into a variable named `refract`, you could retrieve the `mydata` variable using the command `mydata = refract.mydata`.
Learn more about Retrieve variable
brainly.com/question/13061967
#SPJ11
convert the following statement to a valid if statement. if x>y>=z or x
This if statement checks if either (x > y and y >= z) is true or (x < z) is true, and if so, it will execute the code within the if block.
To convert the given statement to a valid if statement using the term "if statement", please follow these steps:
1. First, break down the statement into separate conditions: x > y, y >= z, and x < z.
2. Combine these conditions using the logical operators "and" and "or" as specified in the statement.
3. Form the if statement using the combined conditions.
Here's the resulting if statement:
```python
if (x > y and y >= z) or x < z:
# Your code here
```
Learn more about if statement: https://brainly.com/question/18736215
#SPJ11
which of the following commands can be used to display the filesystem and partition uuids on a linux system? a. e2label
b. blkid
c. fatlabel
d. showpart
The "blkid" command can be used to display the filesystem and partition UUIDs on a Linux system. Option b is the correct answer.
The "blkid" command is a utility that displays information about the available block devices on a system, including their UUIDs. UUIDs (Universally Unique Identifiers) are unique identifiers assigned to filesystems and partitions.
By using the "blkid" command, you can obtain the UUIDs of the filesystems and partitions present on your Linux system. This information is useful for various purposes, such as mounting filesystems, configuring the system's boot loader, or setting up the /etc/fstab file.
Option b. blkid is the correct answer.
You can learn more about Linux system at
https://brainly.com/question/12853667
#SPJ11
the it department has just purchased 15 wireless access points in order to provide full wireless coverage for all 100 employees within the company and is looking to deploy the most secure and scalable wireless implementation. which open source authentication method would perform authentication on behalf of all 15 wireless network devices? tkip wpa2-psk radius tacacs
In order to perform authentication on behalf of all 15 wireless network devices, the IT department would need to deploy a centralized authentication server.
Among the options listed, the open-source authentication method that is designed for this purpose is RADIUS (Remote Authentication Dial-In User Service).
RADIUS provides centralized authentication, authorization, and accounting (AAA) management for wireless and other network devices. With RADIUS, the 15 wireless access points can forward authentication requests to a central RADIUS server, which performs user authentication and authorization based on user credentials stored in a database or directory service. This approach provides a more secure and scalable solution compared to using pre-shared keys (WPA2-PSK) or TKIP, which require each access point to maintain its own set of keys. TACACS is another protocol that can be used for AAA management, but it is typically used for devices such as routers and switches, rather than wireless access points.
To know more about it department click this link -
https://brainly.com/question/27306284
#SPJ11
Homework Assignment Chapter 10b Create a Project named Chap10b Create a class named Vehicle that acts as a superclass for vehicle types. The Vehicle class contains private data fields for the number of wheels and the average number of miles per gallon. The Vehicle class contains getters and setters for the data fields. The Vehicle class also contains a constructor with integer arguments for the number of wheels and average miles per gallons, and a display() method that prints the required output. Create two subclasses, Car and Motorcycle, that extend the Vehicle class. Each subclass contains a constructor that accepts the miles-per-gallon value as an argument and forces the number of wheels to the appropriate value-2 for a MotorCycle and 4 for a Car. Use the superclass constructor to set the wheels and mpg data fields (use the super keyword). Write a UseVehicle class to instantiate one object of each subclass and display the object's values. Save the files as Vehicle.java, Car.java, MotorCycle.java, and UseVehicle.java For reference, see page 490-491. Zip the folder Chap10b and upload. Make sure your code has the following comments at the beginning of each file with the appropriate information: //Filename
//Author //Date Console Output: Car--> Wheels: 4 Mpg: 30 Motorcycle--> Wheels: 2 Mpg: 60
The appropriate comments at the Beginning of each file with the information about the filename, author, and date. Finally, zip the folder Chap10b and upload it for submission.
The Homework Assignment Chapter 10b, you need to create four Java files: Vehicle.java, Car.java, Motorcycle.java, and UseVehicle.java. The Vehicle class is a superclass for vehicle types and contains private data fields for the number of wheels and the average number of miles per gallon, getters and setters for these fields, a constructor with integer arguments for the number of wheels and average miles per gallon, and a display() method that prints the required output.The Car and Motorcycle classes extend the Vehicle class and have constructors that accept the miles-per-gallon value as an argument and force the number of wheels to the appropriate value, 4 for a Car and 2 for a Motorcycle, respectively. Use the superclass constructor to set the wheels and mpg data fields by using the super keyword.The UseVehicle class should instantiate one object of each subclass and display their values by calling the display() method. The output should show "Car--> Wheels: 4 Mpg: 30" and "Motorcycle--> Wheels: 2 Mpg: 60".
Make sure to include the appropriate comments at the beginning of each file with the information about the filename, author, and date. Finally, zip the folder Chap10b and upload it for submission.
To know more about Beginning.
https://brainly.com/question/7788080
#SPJ11
/ Vehicle.java
// Author: [Your Name]
// Date: [Current Date]
public class Vehicle {
private int numWheels;
private int avgMpg;
public Vehicle(int wheels, int mpg) {
this.numWheels = wheels;
this.avgMpg = mpg;
}
public int getNumWheels() {
return this.numWheels;
}
public int getAvgMpg() {
return this.avgMpg;
}
public void setNumWheels(int wheels) {
this.numWheels = wheels;
}
public void setAvgMpg(int mpg) {
this.avgMpg = mpg;
}
public void display() {
System.out.println("Wheels: " + this.numWheels + " Mpg: " + this.avgMpg);
}
}
// Car.java
// Author: [Your Name]
// Date: [Current Date]
public class Car extends Vehicle {
public Car(int mpg) {
super(4, mpg);
}
}
// MotorCycle.java
// Author: [Your Name]
// Date: [Current Date]
public class MotorCycle extends Vehicle {
public MotorCycle(int mpg) {
super(2, mpg);
}
}
// UseVehicle.java
// Author: [Your Name]
// Date: [Current Date]
public class UseVehicle {
public static void main(String[] args) {
Car myCar = new Car(30);
MotorCycle myMotorCycle = new MotorCycle(60);
System.out.print("Car --> ");
myCar.display();
System.out.print("Motorcycle --> ");
myMotorCycle.display();
}
}
// Output:
// Car --> Wheels: 4 Mpg: 30
// Motorcycle --> Wheels: 2 Mpg: 60
Learn more about Vehicle here:
https://brainly.com/question/31842762
#SPJ11
Braydon is working with a partner building a spreadsheet. The partner uses the cell reference $B7 in one of his formulas. What would not change in the formula cell if it is copied and moved by Braydon?
Answer:
If Braydon copies and moves the formula cell that contains the cell reference $B7, the column reference represented by the dollar sign ($) would not change. The dollar sign before the letter "B" in $B7 indicates an absolute column reference.
When a cell reference is absolute, such as $B7, the column reference remains fixed while the row reference can change when the formula is copied or moved to different cells. In this case, if the formula cell is copied and moved horizontally or vertically, the column reference would remain as "B" in the copied cells.
For example, if Braydon copies and moves the formula cell with $B7 to a new location, the copied cells would still refer to column "B" in their respective rows. For instance, the copied formula in the cell below would still reference column "B":
$B8
Therefore, the column reference represented by $B would not change when Braydon copies and moves the formula cell.
What does the cli option do on the model statement of an mlr analysis in proc glm?
"cli" option in the model statement of an MLR analysis in PROC GLM.The "cli" option in the model statement of a multiple linear regression (MLR) analysis in PROC GLM stands for "confidence limits for individual parameters."
When you include this option in your analysis, it calculates the confidence intervals for the regression coefficients of each predictor variable in the model.
To use the "cli" option, follow these steps:
1. Start your PROC GLM statement: PROC GLM data=your_dataset;
2. Specify your model statement with the "cli" option: MODEL dependent_variable = predictor_variables / cli;
3. End the PROC GLM statement with a "quit;": QUIT;
By including the "cli" option in your model statement, PROC GLM will provide you with the lower and upper confidence limits for each regression coefficient, allowing you to assess the precision of the estimated parameters.
Remember to replace "your_dataset" with the name of your dataset, "dependent_variable" with the response variable you are analyzing, and "predictor_variables" with the list of predictor variables in your model.
To know more about Cli visit:-
https://brainly.com/question/31680699
#SPJ11
What is the result of executing the following query in Prolog REPL? ?-[X, Y|T] = [a,b,c] O X = a Y = b, T = C. OX= a, Y=b, T = [C] OX= [a], Y = [b] T=[C] O false.
The result of executing the following query in a Prolog REPL would be:
X = a, Y = b, T = [c]
Prolog, short for "Programming in Logic," is a high-level programming language associated with artificial intelligence and computational linguistics. It's a declarative language, meaning programs are composed of a series of declarations, or facts and rules, rather than explicit step-by-step instructions. Prolog is known for its strong support of pattern matching and automatic backtracking, which are useful in problem-solving and knowledge representation. The language is primarily used for theorem proving, expert systems, term rewriting, type systems, and automated planning, making it a popular choice in the field of AI research and development.
Learn more about Prolog here:
https://brainly.com/question/30388215
#SPJ11
What is the output of this program?
ages = [13, 17, 20, 43, 47]
print(ages[3])
A.
3
B.
20
C.
43
D.
47
Note that the the output of this program is 43.
what is an output?A software may need interaction with a user. This might be to display the program's output or to seek more information in order for the program to start. This is commonly shown as text on the user's screen and is referred to as output.
The list ages in the preceding program comprises five elements: 13, 17, 20, 43, and 47.
The line print(ages[3]) outputs the fourth entry of the list (remember, Python counts from 0).
As a result, the output is 43.
Learn mor about output:
https://brainly.com/question/13736104
#SPJ1
if text_line = 'one fish two fish', what is the value of text_line[6]? group of answer choices 'h' ' ' 'i' 's'
The value of text_line[6] would be 's', because text_line[6] represents the character at the 6th index of the string 'one fish two fish'.
In the given text_line = 'one fish two fish', each character has a specific index. The indexing starts from 0, so text_line[6] refers to the 7th character in the string.
In this case, the 6th index is the letter 's'.
Therefore, when accessing text_line[6], the value returned will be 's'.
It's important to note that in Python, strings are indexed starting from 0, so the first character of a string is represented by text_line[0], the second character is represented by text_line[1], and so on.
Learn more about python at https://brainly.com/question/20361395
#SPJ11
true or false? a file server is a computer dedicated to storing and managing files for network users.
The statement is true. A file server is a computer dedicated to storing and managing files for network users.
A file server is a computer or a specialized device that is dedicated to storing and managing files for network users. It provides centralized file storage and allows users connected to the network to access and share files from a single location. File servers typically have large storage capacities and are designed to handle high volumes of file requests from multiple users simultaneously. They are equipped with file server software that enables functions such as file sharing, access control, file organization, and file backup.
By using a file server, organizations can streamline file management, improve data accessibility, and enhance collaboration among users. Network users can store their files on the file server, access them from different devices and locations, and share files with other authorized users on the network. In summary, a file server serves as a dedicated system that centrally stores and manages files for network users, providing efficient and secure access to shared files within an organization.
Learn more about network here: https://brainly.com/question/30456221
#SPJ11
Write the function insertInOrder() which inserts each of the elements in the source array into the ordered position in the destination array. You may assume that the destination array is already in sorted order. Here is a short example: int src[50]15, 7, 9); int dest[50]6, 8}; size t dSize - 2; bool ok - insertInorder(dest, dsize, 50, src, 3)i As you can see the function takes 5 arguments: The destination array and its size, which may both be modified. The destination capacity, the source array and the source size, which are not modified. . In the example shown above, the function will return true (since it can succeed) and the resulting array will contain: 15, 6, 7, 8, 9. The new dSize will be 5. The function returns false if it fails. The only reason it could fail is if inserting the new elements would cause the capacity to be exceeded, in which case the destination array should not be changed in any way.
The function insertInOrder() is a useful function that allows us to insert elements from a source array into a destination array in their proper sorted order. The function takes in five arguments, namely the destination array and its size, the destination capacity, the source array, and the source size. It modifies the destination array and its size.
The algorithm for the function is simple. We start by iterating through each element of the source array.
For each element, we check where it should be inserted in the destination array. We do this by comparing it to each element in the destination array until we find the correct position.
Once we have found the correct position, we shift all the elements after that position one index to the right, making space for the new element. Finally, we insert the new element in the correct position.
The function returns true if it succeeds in inserting all the elements from the source array into the destination array without exceeding the destination capacity.
If the destination capacity is exceeded, the function returns false and does not modify the destination array in any way.
In the example given, we have two arrays, dest and src.
The function is called with these arrays, their sizes, and the destination capacity.
The function succeeds in inserting all the elements from the src array into the dest array, resulting in the modified dest array containing 15, 6, 7, 8, and 9, and a new size of 5. The function returns true.
The insertInOrder() function is a useful tool for sorting and inserting elements into arrays. Its simplicity and efficiency make it a valuable addition to any programming toolkit.
For more questions on array
https://brainly.com/question/29989214
#SPJ11
what is used to request access to services in the kerberos process? 1 point client id tgs session key ticket granting ticket client-to-server ticket
In the Kerberos process, the client uses a Ticket Granting Ticket (TGT) to request access to services.
The TGT contains the client's identity, a session key, and is issued by the Key Distribution Center (KDC).
In the Kerberos authentication protocol, the client initiates the process by presenting its credentials to the KDC. The KDC verifies the client's identity and issues a TGT, which includes the client's identity, a session key, and an expiration time. The TGT is encrypted with the KDC's private key.
When the client wants to access a particular service, it sends a request to the Ticket Granting Service (TGS) along with the TGT. The TGS authenticates the client and issues a Client-to-Server Ticket (CST) that contains the client's identity and a session key specifically generated for the requested service. The CST is encrypted with the server's key.
Therefore, the TGT is used to request access to services in the Kerberos process, and the CST allows the client to access a specific service securely.
Learn more about security click here:
brainly.com/question/30174427
#SPJ11
(Count positive and negative numbers and compute the average of numbers) Write a program that reads an unspecified number of integers, determines how many positive and negative values have been read, and computes the total and average of the input values (not counting zeros). Your program ends with the input 0. Display the average as a floating-point number. Sample Run 1 Sample Output 1: Enter an integer, the input ends if it is 0: 1 Enter an integer, the input ends if it is 0: 2 Enter an integer, the input ends if it is 0: -1 Enter an integer, the input ends if it is 0: 3 Enter an integer, the input ends if it is 0: 0 The number of positives is 3 The number of negatives is 1 The total is 5 The average is 1. 25 Sample Run 2 Sample Output 2: Enter an integer, the input ends if it is 0: 0 No numbers are entered except 0
The program prompts the user to enter integers until they input 0. It counts the number of positive and negative values, computes the total sum, and calculates the average (excluding zeros).
If no numbers are entered except 0, it displays an appropriate message. The main code uses a while loop to repeatedly read the input and update the variables. Finally, it prints the counts, total, and average values based on the entered numbers.
Learn more about computes here;
https://brainly.com/question/31064105
#SPJ11
Which Oracle Cloud Infrastructure (OCI) service can be configured to send you an alert for high CPU usage?
Monitoring
Logging Analytics
Events
Analytics
Loggingds
The Oracle Cloud Infrastructure (OCI) service that can be configured to send you an alert for high CPU usage is: Monitoring.
What is the infrastructure?The Oracle infrastructure that can help a person to receive alerts when some limits have been exceeded is the monitoring framework.
For instance, if you are making a budget and want to set a limit so that when these are exceeded, your attention can be called to them, then the monitoring feature will help you.
Learn more about Oracle here:
https://brainly.com/question/31455535
#SPJ1
If a base has a Kb value of 6.5 x 10-3, what is the pKb of the base?
2.19
1.87
2.95
3.01
3.49
A). The pKb of the base is 2.19. The pKb value can be calculated using the formula: pKb = -log(Kb).
Substituting the given Kb value, we get pKb = -log(6.5 x 10^-3) = 2.19
The pKb of a base can be calculated using the formula: pKb = -log10(Kb). Given that the Kb value of the base is 6.5 x 10^-3, we can calculate the pKb as follows.
pKb = -log10(6.5 x 10^-3) = 2
The net equation for the autoionization of water is obtained by multiplying the acid and base processes together, which is identical to Ka * Kb. It's neither an acid-base or neutralisation reaction, but I believe the Kw = Ka * Kb relationship is a mathematical formula used to speed up calculations.
To know more about pKb visit-
https://brainly.com/question/14124805
#SPJ11
In the OSI model, which of the following functions are performed at the Application layer?
The Application layer in the OSI model handles functions related to network applications and user interfaces.
What types of tasks are performed at the Application layer in the OSI model?The Application layer, the highest layer in the OSI model, is responsible for providing network services to applications and end-users. It focuses on tasks such as file transfers, email services, web browsing, and remote logins.
This layer ensures that data is properly formatted and interpreted by the receiving application. It also manages encryption, authentication, and data compression.
Additionally, the Application layer facilitates web browsing, enabling users to access and interact with websites. These functions involve proper formatting, interpretation, and presentation of data to the respective applications.
Furthermore, the Application layer manages tasks like encryption, authentication, and data compression to enhance network security and efficiency.
In summary, the Application layer serves as the interface between the network and the software applications running on a device.
Learn more about OSI model
brainly.com/question/31023625
#SPJ11