Suppose that the current value of PC is 0x00004000. Can we use a single jump instruction to go to PC= 0x20014924?(if yes, write the jump instruction and show the value of the immediate field in Hex. If not, use a combinations of instructions to do so and show the immediate values in Hex)

The angle of twist at the end A is approximately 0.02035 radians.

To calculate the angle of twist at the end A of a tapered shaft, we use the formula:

θ = ∫(T/(GJ))dx

Where θ is the angle of twist, T is the applied torque, G is the shear modulus of elasticity, and J is the polar moment of inertia, which for a circular cross-section is J = (π/2)r^4.

The given function for the radius r is r = 0.02(1 + x^3/2). Substituting this into the equation for J and integrating with respect to x from 0 to L (the length of the shaft) gives:

θ = ∫(T/(G(π/2)(0.02(1 + x^3/2))^4))dx

= ∫(T/(G(π/2)(0.02)^4(1 + x^3/2)^4))dx

= 16T/(G(π)(0.02)^4) ∫(1/(1 + x^3/2)^4)dx

Substitute the given values: T = 440 N⋅m, G = 27 GPa = 27 * 10^9 Pa.

After evaluating the integral and plugging in the values, we get:

θ = 0.02035 radians

Therefore, the angle of twist at the end A is approximately 0.02035 radians

Learn more about angle of twist below.

https://brainly.com/question/13440469

#SPJ1

For the system of prelab, from the given transfer function evaluate the percent overshoot, settling time, peak time, and rise time for the values a and b.

3. a. To increase the imaginary part of the poles of the system of Prelab 2a, by a factor of two, the values of a and b should be set to a = 8 and b = 50. This will result in the transfer function of G(s) = 52 + 8s + 50. After calculating the new values, repeating Prelab 2a is necessary.

b. To increase the real part of the poles of the system of Prelab 2a by a factor of two, the values of a and b should be set to a = 8 and b = 100. This will result in the transfer function of G(s) = 52 + 8s + 100. After calculating the new values, repeating Prelab 2a is necessary.

Given the transfer function G(s) = 52 + as + b, with a = 4 and b = 25, the percent overshoot is 57.75%, the settling time is 0.212 seconds, the peak time is 0.106 seconds, and the rise time is 0.105 seconds. The poles of the transfer function should also be plotted.

To increase the real part of the poles of the system of Prelab 2a by a factor of two, the values of a and b should be set to a = 8 and b = 50. This will result in the transfer function of G(s) = 52 + 8s + 50. After calculating the new values, repeating Prelab 2a is necessary.

To decrease the real part of the poles of the system of Prelab 2a by a factor of two, the values of a and b should be set to a = 2 and b = 25. This will result in the transfer function of G(s) = 52 + 2s + 25. After calculating the new values, repeating Prelab 2a is necessary.

Learn more about the transfer function at:

https://brainly.com/question/31161605

#SPJ11

According to the question of python that raises an error, the answer of the question is true.

Python is a widely used high-level, general-purpose, interpreted, dynamic programming language. It is designed to be highly readable with its notable use of significant whitespace. Its language constructs and object-oriented approach aim to help programmers write clear, logical code for small and large-scale projects. Python is a multi-paradigm programming language, providing support for object-oriented, imperative and functional programming or procedural styles. It also has a large and comprehensive standard library. Python is open-source and can be used for any purpose, including commercial projects. It is also popular in scientific and numeric computing. Python is also used to power many popular web frameworks such as Django and Flask, and is used to develop games as well.

To learn more about python

https://brainly.com/question/29563545

#SPJ1

The answer of the given question based on the Swapping of the list with the given parameter numList  is a list of numbers and the parameters j and k are integers the most appropriate documentation is given below,

In computing, a parameter is a value or a reference passed to a function, procedure, or method as input. Parameters allow a function or method to accept input data and perform operations on it, producing output data.

In programming, parameters are defined within the function or method signature and can be of different data types, such as integers, strings, arrays, objects, or other values. Parameters are separated by commas within the parentheses of the function or method definition, and they can have default values or be optional.

Here is an appropriate documentation for the swapListElements procedure:

PROCEDURE swapListElements(numList, j, k)

DESCRIPTION:

This procedure takes a list of numbers and two integer indices, j and k, and returns a new list with the elements at positions j and k swapped.

PARAMETERS:

- numList: A list of numbers

- j: An integer index representing the position of an element in numList

- k: An integer index representing the position of another element in numList

RETURN:

A new list with the elements at positions j and k swapped.

EXAMPLES:

swapListElements([1, 2, 3, 4], 0, 2) -> [3, 2, 1, 4]

swapListElements([10, 20, 30], 1, 2) -> [10, 30, 20]

This documentation provides a clear description of what the procedure does, the parameters it takes, and the return value. It also includes examples to demonstrate how to use the procedure.

To know more about Function visit:

https://brainly.com/question/16917020

#SPJ1

The correct order in which the parts of the cardiac conduction system transmit the action potential is:

3, 6, 1, 4, 2, 5

The action potential originates in the sinoatrial (SA) node (located in the right atrium) and spreads to the atria, causing them to contract.

The action potential then reaches the atrioventricular (AV) node, which delays the impulse for a short period to allow for complete contraction of the atria before the ventricles contract.

'The action potential then travels down the AV bundle (also known as the bundle of His), which is located in the interventricular septum, and branches into the right and left bundle branches.

The right and left bundle branches carry the action potential to the Purkinje fibers, which spread throughout the ventricular myocardium.

The Purkinje fibers then transmit the action potential to the contractile cells of the cardiac muscle tissue, causing the ventricles to contract.

Read more about cardiac systems here:

https://brainly.com/question/946975

#SPJ1

Answer:

100000

Explanation:

based on the information i have it is up to 70000 but 100000 is closer so choose it

To determine the smallest pinion tooth count that will run with itself, we can use the formula:

N = (2sin(phi/2))/(1-sin(phi/2))

where N is the tooth count.

Substituting phi = 20 degrees, we get:

N = (2sin(20/2))/(1-sin(20/2)) = 22.86

Therefore, the smallest pinion tooth count that will run with itself is 23 teeth.

To find the smallest pinion tooth count at a ratio me = 2.5, we can use the formula:

N2/N1 = me

where N1 and N2 are the pinion and gear tooth counts, respectively, and me is the gear ratio.

Substituting me = 2.5, we get:

N2/N1 = 2.5

We need to choose the smallest integer values of N1 and N2 that satisfy the above equation while avoiding interference. We can use the formula for the minimum number of teeth for the pinion:

N1min = (2C)/(pidiametral pitchsin(phi))

where C is the center distance and diametral pitch is the number of teeth per inch of pitch diameter.

For a given center distance and diametral pitch, we can calculate the minimum number of teeth for the pinion and gear, and check if they satisfy the gear ratio equation while avoiding interference. We can use a gear design software or tables to find suitable values.

Assuming we find a suitable pinion with N1 = 16 teeth, we can find the maximum gear tooth count using the formula:

N2max = me*N1 + 2

Substituting me = 2.5 and N1 = 16, we get:

N2max = 2.5*16 + 2 = 42

Therefore, the largest gear tooth count possible with this pinion is 42 teeth.

To find the smallest pinion that will run with a rack, we can use the formula:

N1min = (2C)/(pi*module)

where module is the metric equivalent of the diametral pitch and C is the center distance.

For a given center distance and module, we can calculate the minimum number of teeth for the pinion and check if it is available. If not, we can increase the module and try again. Alternatively, we can use gear design software or tables to find suitable values.

Note: To avoid interference, the minimum number of teeth for the pinion should be at least 17 for phi = 20 degrees.

To know more about smallest pinion tooth count click here:

brainly.com/question/13110578

#SPJ4

The following is an example of how to use the useradd command to add a new user to the "newuser" supplementary group in Linux, using the -G option.```useradd -G newuser```

The following are the options for the useradd command to add supplementary groups the user will be a member of:Option A: -uOption B: -sOption C: -SOption D: -GOption E: -FExplanation:To add a new user to the system or modify an existing account, the useradd command is used in Linux. The new user's initial login password can be set using the command. The useradd command's syntax is simple, with the useradd command followed by the username, options, and arguments.The following are the options for the useradd command to add supplementary groups the user will be a member of:Option A: -uOption B: -sOption C: -SOption D: -GOption E: -FThe "-G" option is used with the useradd command to add the user to a supplementary group or groups, as shown above. By specifying one or more groups separated by commas, you can assign the user to multiple groups.

To learn more about .Linux

https://brainly.com/question/31040070

#SPJ11

The signal, when converted to phasor form with a phasor value of V_1 is 1.25 - 2.165j.

To convert the given signal V_1 = 5cos(200pi*t - 60°) to phasor form, we will use Euler's identity and the phasor notation.

Euler's identity states that:

cos(θ) = 0.5 * (e^(jθ) + e^(-jθ))

First, we express the given signal using Euler's identity:

V_1 = 5 x (0.5 x (e ^ ( j x (200pit - 60°)) + e^(-j x (200pit - 60°))))

V_1 = 5/2 x (e^ ( j x (200pit - 60°)) + e^(-j x (200pit - 60°)))

The phasor notation represents only the complex exponential term with a positive exponent.

In rectangular form:

V_1 phasor = 5/2 x (cos (-60°) + jsin(-60°))

V_1 phasor = 5/2 x (0.5 - j0.866)

V_1 phasor = 1.25 - 2.165j

Find out more on phasor form at https://brainly.com/question/30903013

#SPJ1

The inner diameter of the spring (ID) is 0.93 in. The spring constant (Ks) is 3.04 lb/in. The number of active coils (Na) is 4. The total number of coils (Nt) is 6. The deflection constant (c) is 1.12 in/lb.

To calculate the ID, we first need to subtract the wire diameter (0.085 in) from the outside diameter (1.1 in) and then divide by 2, which gives us an ID of 0.93 in.

To find Ks, we use the formula Ks = Gd^4/8D^3n, where G is the shear modulus of the material (assumed to be 11.5x10^6 psi), d is the wire diameter, D is the mean coil diameter (which can be approximated by averaging the ID and OD), and n is the number of active coils. Plugging in the values gives us Ks = 3.04 lb/in.

Na can be determined by counting the number of coils in the spring that are free to deflect under load, which is 4 in this case. Nt is simply the total number of coils, which is 6.

Finally, to calculate c, we use the formula c = 4GD^3/3nD^4 - d^4, where G, D, d, and n are the same as before. Plugging in the values gives us c = 1.12 in/lb.

For more questions like Spring constant click the link below:

https://brainly.com/question/14159361

#SPJ11

The four broad classes of services that a transport protocol can provide are: Reliable data transfer, Throughput guarantees, Timeliness guarantees and Confidentiality.

Reliable data transfer - this ensures that data sent from one end is received correctly and completely at the other end. It includes error detection, retransmission of lost or corrupted packets, and flow control. TCP provides reliable data transfer, but UDP does not.

Throughput guarantees - this ensures that a certain level of network throughput will be maintained for a connection. This can be useful for applications that require a minimum level of network performance, such as multimedia streaming. Neither TCP nor UDP provides throughput guarantees.

Timeliness guarantees - this ensures that data will be delivered within a specified amount of time. This is important for real-time applications such as voice and video conferencing, where delays can cause disruptions. Both TCP and UDP can provide timeliness guarantees, but UDP is often preferred for real-time applications due to its lower overhead.

Confidentiality - this provides data encryption to ensure that data cannot be intercepted and read by unauthorized parties. Neither TCP nor UDP provides confidentiality, but it can be implemented at the application layer using encryption protocols such as SSL/TLS.

Learn more about Transport protocol :https://brainly.com/question/26284086

#SPJ11

On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be properly designed and maintained.

Reciprocating engine aircraft (also known as piston engine aircraft) are airplanes that are powered by reciprocating engines. Reciprocating engines are internal combustion engines that employ a piston and cylinder to convert fuel into mechanical energy.

They are typically used in smaller aircraft, such as general aviation planes and private aircraft. A shrouded exhaust muffler system is an aircraft exhaust system that is designed to reduce noise and heat by enclosing the muffler within a protective shroud.

This type of system is commonly used on reciprocating engine aircraft as a source of cabin heat. The exhaust system of an aircraft should be properly designed and maintained in order to ensure safe and reliable operation.

In addition, the exhaust system should be designed to minimize the risk of carbon monoxide poisoning, which can be a serious safety hazard on aircraft.

For such more question on reciprocating:

https://brainly.com/question/13040264

#SPJ11

Here are n possible starting positions for the algorithm, the average number of trips for the algorithm to find x in the array t[1...n] is (n(n+1)/4)/n = (n+1)/2.Therefore, the average number of trips for the algorithm to find x in the array t[1...n] is (n+1)/2.

Algorithm sequential (t[1..n],x) is a searching algorithm that finds an element x in the array t[1...n]. According to the question, let's assume that x is somewhere in the array, the elements of t are distinct, and x can be found with equal probability at each possible position. Now, we need to prove that (n 1)/2 is the average number of trips around the loop.   Proof: Let's assume that x is the ith element of the array t, where 1 ≤ i ≤ n.Let's consider two cases:Case 1: The algorithm starts at the first position of the array t[1], and x is found at position i.Let's assume that the algorithm takes k trips to find x from position 1 to i. For the algorithm to find x, it needs to check k elements of the array that are before the position i. The probability of the algorithm checking any of the previous k - 1 elements is (1/2), as the position of x is equally likely to be at any position before or after the kth element. Therefore, the probability of finding x on the kth try is (1/2).Thus, the expected number of trips for the algorithm to find x from position 1 to i is ∑k=1i k*(1/2) = i/2.Case 2: The algorithm starts at position j, where 2 ≤ j ≤ i, and x is found at position i.Let's assume that the algorithm takes k trips to find x from position j to i. For the algorithm to find x, it needs to check k elements of the array that are before the position i. The probability of the algorithm checking any of the previous k - 1 elements is (1/2), as the position of x is equally likely to be at any position before or after the kth element. Therefore, the probability of finding x on the kth try is (1/2).Thus, the expected number of trips for the algorithm to find x from position j to i is ∑k=1i-j+1 k*(1/2) = (i-j+1)/2.So, the total expected number of trips for the algorithm to find x in the array t[1...n] is ∑i=1n (i/2) = (n(n+1)/4).

Learn more about algorithm

brainly.com/question/22984934

#SPJ11

Unfortunately, it is not possible to draw a picture of memory after executing statements. Memory is a complex system, and it would be difficult to accurately represent it in a single picture. However, you can use words to describe the state of memory after executing these statements.

for more such question on variables

https://brainly.com/question/28248724

#SPJ11

True. A torpedo level is a short level that is commonly used in construction and woodworking. It typically has a length of about 9 inches and is designed for portability and convenience.

The level uses an air bubble located inside a liquid-filled vial to establish plumb and level references. When the bubble is centered between two lines marked on the vial, the object being measured is level or plumb. Torpedo levels are useful for a wide range of applications, including installing cabinets, leveling shelves, and hanging pictures. They are also commonly used by plumbers and electricians for rough-in work.

Find out more about torpedo level

brainly.com/question/23105041

#SPJ4

The function gets Ints From File(std::string fileName) should return a std::vector containing all the integer values present in the file fileName.

To do this, you can use an input stream to read the contents of the file line by line and then use a string stream to parse the line into a sequence of integers. You should also use exception handling to recover from any formatted read failures and continue reading integer values from the file. For example:
try {
   // open an input stream
   std::ifstream inputStream(fileName);
   std::string line;
 
   // read each line in the file
   while(std::getline(inputStream, line)) {
       // create a string stream from the line
       std::istringstream stringStream(line);
       // parse the line into a sequence of integers
       int value;
       while(stringStream >> value) {
           // add the integer to the vector
           std::vector.push_back(value);
       }
   }

} catch(std::exception& e) {
   // handle the formatted read failure
}

To learn more about "string": brainly.com/question/639262

#SPJ11

The question is: "Which of the following are true about the differences between RISC and CISC architectures? Select all that apply." The following are true about the differences between RISC and CISC architectures:

Uncomplicated Instructions As compared to other microprocessor designs, computers use a limited, highly efficient set of instructions as opposed to a more specialized set of instructions. a type of processor design that moves the computing task's analysis from the runtime or execution phase to the preparation or compilation phase. The system can run at faster rates by utilizing less hardware or logic.

Learn more about CISC architectures: https://brainly.com/question/13266932

#SPJ11

The potential at the center of a spherical shell of uniform surface charge density [tex]P_o[/tex] with radius a, assuming the potential at infinity is zero.

The electric field due to the shell can be determined by using Gauss' law and expressed in cylindrical coordinates:

[tex]Er = P_{o} /2\pi\epsilon_0 r^2[/tex]

Where r is the radial distance. The electric potential can then be calculated by integrating this equation:

[tex]V(r) = 1/4\pi\epsilon_0 P_oa/r -1/4\pi \epsilon_0P_oa^2/r^2[/tex]

Therefore, the potential at the center of the spherical shell, which has a radius of a, is:

[tex]V_(r=0) = -P_oa^2/4\pi\epsilon_0[/tex]

Alternatively, the potential at the center of the spherical shell can also be determined by using the potential-charge formula, which states:

[tex]V(r) = 1/4\pi\epsilon_0Q/r[/tex]

Where Q is the total charge. For the spherical shell, the total charge is equal to the surface charge, or [tex]Q = P_o*4\pi a^2[/tex]. Plugging this into the potential-charge formula, we get:

[tex]V(r=0) = -P_oa^2/4\pi\epsilon_0[/tex]

Thus, the potential at the center of the spherical shell of uniform surface charge density [tex]P_o[/tex] and radius a is equal to [tex]-P_oa^2/4\pi\epsilon_0[/tex] when the potential at infinity is assumed to be zero.

Learn more about the potential at:

https://brainly.com/question/14306881

#SPJ11

The Cartesian coordinates x, y of the center C of the osculating circle at t = 2 s are x = -3.077 m and y = 0.686 m.

At time t=2s, the position vector of the moving point is given by

r = (3t² + 2t – 3)î + (−3+2 – 3t – 2)î m.

To calculate the Cartesian coordinates of the center of the osculating circle at t=2s, we must first calculate the curvature k at t=2s. We can do this using the formula:

k = |dv/dt| / |r|³

where dv/dt is the derivative of the velocity vector with respect to t and r is the position vector. Since the velocity vector is v = dr/dt = (6t + 2)î + (-6t-3)î, the derivative of the velocity vector is dv/dt = (6)î + (-6)î. Therefore,

k = sqrt(6² + (-6)²) / |r|³

Using the given position vector and substituting t=2, we find that

k = sqrt(60) / |r|³ = sqrt(60) / (sqrt(61))³ = 2.95

Now, using the formula

C = r + (1/k) × (v/|v|) × (r × v)

we can calculate the coordinates of center C. We have already calculated the value of k. The velocity vector v = (6t + 2)î + (-6t-3)î and its magnitude

|v| = sqrt((6t+2)² + (-6t-3)²) = sqrt(60).

Also,

r x v = (-3)î + (3t+2)î × (6t + 2)î + (-6t-3)î = (3t² + 6t + 7)î.

Therefore,

C = r + (1/k) × (v/|v|) × (r × v)

= (3t² + 2t – 3)î + (−3+2 – 3t – 2)î + (1/2.95) × (sqrt(60)) × (-3)î + (3t² + 6t + 7)î

Substituting t=2, we find that

C = (-3.077, 0.686) m

To learn more about  Cartesian coordinates :

https://brainly.com/question/13255257

#SPJ11

Answer:

xori t1,t2,-1

Explanation:

the not instruction is converted into xor immediate as not t1,t2 would mean that which is equal to xor

t1 t2 nott1 nott2 result

0  1    1         0        0

1  0    0        1         0

1  1    0         0        1

0 0   1          1         0

In order to set all the indexed variables to 0 in an array, there are several options for the definition of the array. The correct options for this question are:

int array[5] = {0,0,0,0,0};int array[5] = {};int array[5] = {0};Option a sets all the indexed variables to 0. This is achieved by providing a comma-separated list of values enclosed in curly brackets {} that match the size of the array. Since this array has a size of 5, there must be 5 values within the brackets.

Option b is incorrect because it contains an "x" instead of values separated by commas within the brackets. This would not compile properly and set the values to 0.Option c is also incorrect because it contains a sequence of values starting at 0 and incrementing by 1 up to 4. This would not set all the values to 0.Option d is incorrect because it sets only the first indexed variable to 0 and leaves the remaining variables with undefined values.

For more such questions on  indexed variables

https://brainly.com/question/24167993

#SPJ11

The option that defines how positions are measured on the background in the following background property: position.

Positions are the places or orientations of objects relative to each other. They are used to describe the orientation of a physical object in space, or the physical location of an object in a two-dimensional or three-dimensional environment. Positions can be described in terms of x, y and z coordinates, which are used to denote the position of an object in a three-dimensional space. Positions can also be described in terms of angles and distances, which are used to denote the orientation of an object in a two-dimensional space. Positions can be used to describe the location of an object in relation to another object in a scene, or the relationship between different objects in the same scene.

To learn more about positions

https://brainly.com/question/17422777

#SPJ1

The two principal climate components are "temperature and precipitation". Hence, option A is the correct answer.

Climate refers to the weather conditions that are characteristic of a particular place or region over a long period. It is a pattern of weather conditions that prevails over a long period of time in a specific area. It includes the average weather conditions, patterns, and changes in temperature, humidity, atmospheric pressure, precipitation, wind, and sunshine.

The two primary factors that determine the climate of a region are temperature and precipitation. They are the two primary climate components. Climate can be influenced by a variety of factors, such as latitude, altitude, topography, ocean currents, and so on. It is influenced by the earth's rotation and tilt, which affects the distribution of sunlight.

You can learn more about Climate at

https://brainly.com/question/17922964

#SPJ11

The steps for the Gram Stain procedure, in order, is (B) Place the bacterial sample on a slide, add crystal violet, add iodine, add decolorizer, add safranin.

The Gram Stain is a common laboratory technique used to differentiate bacteria into Gram-positive and Gram-negative groups based on their cell wall structure. This is the standard order of the Gram Stain procedure, which involves staining bacterial cells with crystal violet, applying iodine to form a complex with the crystal violet, decolorizing with alcohol or acetone, and then counterstaining with safranin to visualize the cells.

Correct answer is option B.

You can learn more about Gram Stain procedure at

https://brainly.com/question/30623143

#SPJ11

The answer of the given question based on the My SQL  on retrieving students who register for all levels of a course the query is given below.

In the context of databases, a query is a request for data or information from a database. It is a command given to the database management system (DBMS) to retrieve or modify data stored in the database. Queries are typically written in a structured query language (SQL) that is specific to the particular database management system being used.

A query can be used to retrieve a single row of data or multiple rows of data that meet certain conditions or criteria. It can also be used to insert, update, or delete data in the database.

Based on the provided tables, the following MySQL query should retrieve students who register for all levels of a course:

SELECT r.ssn, c.school, c.course

FROM registrations r

INNER JOIN courses c ON r.code = c.code

WHERE c.level <= (

   SELECT MAX(c1.level)

   FROM courses c1

   WHERE c1.code = c.code

)

GROUP BY r.ssn, c.code

HAVING COUNT(DISTINCT c.level) = (

   SELECT COUNT(DISTINCT c2.level)

   FROM courses c2

   WHERE c2.code = c.code

)

ORDER BY r.ssn;

This query uses a subquery to find the maximum level of a course and compares it to the level of the registration to ensure that the registration is for all levels of the course. It also uses a GROUP BY clause to group the results by student and course and a HAVING clause to filter the results to only those students who have registered for all levels of a course. Finally, it sorts the results by student's SSN.

Note: The query assumes that the registrations and courses tables are related by the code column.

To know more about Clause visit;

https://brainly.com/question/17247221

#SPJ1

A Work Breakdown Structure (WBS) is a hierarchical tree of work elements or items accomplished or produced by the project team during the project.

A Work Breakdown Structure (WBS) is an essential project planning and management tool that helps to organize and communicate project-related work and deliverables into a logical and manageable framework. It is a process that breaks down complex projects into smaller, more manageable tasks that are easier to complete by project teams.

However, the WBS can only be as accurate and detailed as the project manager's knowledge of the project and the level of stakeholder and team input. Therefore, the WBS is an iterative and interactive process that evolves over the project life cycle and changes as new information is obtained.

It is recommended that project managers use a software program to create, store, and share the WBS. The software should enable collaboration between project managers and team members, allow for updates and revisions, and provide access to critical project information.

For such more question on hierarchical:

https://brainly.com/question/30166876

#SPJ11

The following sequence of the operations is performed on a stack PUSH(10), PUSH(20), POP, PUSH(10), PUSH(20), POP, POP, POP, PUSH(20), POP the sequence of values popped out is option D. 20, 20, 10, 20, 10.

What is a stack?

A stack is a linear data structure that allows elements to be inserted and removed from only one end. It follows the LIFO (Last In First Out) rule, which means the element that was last to be inserted is the first to be removed.

Let's go through the given sequence step by step:

PUSH(10): The stack now contains 10.

PUSH(20): The stack now contains 20,10.

POP: The top element is popped out, so the stack now contains 10.

PUSH(10): The stack now contains 10,10.

PUSH(20): The stack now contains 20,10,10.POP: The top element is popped out, so the stack now contains 10,10.POP: The top element is popped out, so the stack now contains only one element, 10.

POP: The last element is popped out, and the stack is empty.

PUSH(20): The stack now contains 20.

POP: The last element is popped out, so the stack is empty.

Therefore, the sequence of values popped out is 20,20,10,20,10. Hence, option D is correct.

Learn more about  stack:https://brainly.com/question/13152669

#SPJ11

The lot sizing rule such as "the fixed-order quantity rule" bases the order quantity on a standard-size container or pallet load. The answer is b. The fixed-order quantity rule.

The fixed-order quantity rule is a lot sizing technique that bases the order quantity on a standard-size container or pallet load. This rule is also known as the economic order quantity (EOQ) model, and it seeks to balance the ordering costs and holding costs of inventory to determine the optimal order quantity.

The fixed-order quantity rule works by setting a specific order quantity that is ordered every time inventory reaches a certain reorder point. This rule assumes that the demand rate is known and constant, and that the lead time for receiving inventory is also known and constant.

Other lot sizing rules include the lot-for-lot rule, which orders the exact amount of inventory needed to fulfill demand, the periodic-order quantity rule, which orders a fixed amount of inventory at regular intervals, and the gross requirements rule, which calculates the total amount of inventory needed to meet demand over a certain period of time.

You can learn more about fixed-order quantity rule at

https://brainly.com/question/29913445

#SPJ11

The molecular weight of protein band A = 11,139 Da. The molecular weight of protein band B = 7,715 Da.

SDS-polyacrylamide gel electrophoresis (SDS-PAGE) and Gel Filtration (GF) on Sephadex G-200 are both techniques used to determine the molecular weight of a protein.

The molecular weight of proteins B and A can be calculated using the equation: Molecular weight (Da) = (Rm of protein band A/Rm of lysozyme) x 14,000. The Rm of protein band A is 0.562 and the Rm of lysozyme is 0.714. The molecular weight of protein band A= (0.562/0.714) x 14,000 = 11,139 Da.

The difference in the molecular weights obtained by the two techniques can be explained by the presence of protein aggregates, glycosylation, or disulphide bonds.

Gel Filtration on a Sephadex G-200 column under non-denaturing (native) conditions will give a molecular weight of 150,000 daltons, as it considers the molecular weight of the native protein and its tertiary structure.

The SDS-polyacrylamide gel electrophoresis experiment gives a molecular weight of the protein in its denatured form, thus the lower molecular weight obtained. Therefore, the protein is likely to have an overall higher molecular weight due to tertiary structure and other modifications.

From this data, it can be concluded that the protein has a complex tertiary structure with a high molecular weight due to possible modifications such as glycosylation or disulphide bonds. Additionally, the presence of aggregates and dimers can also increase molecular weight.

Learn more about molecular weights at:

https://brainly.com/question/15268826

#SPJ11

Answer:

c. hazards

Explanation:

The safety engineer uses a logging and monitoring system to track hazards from a project's start to its finish.