Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.
The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.
learn more about power here:
https://brainly.com/question/22285866
#SPJ4
A straight 2.80 m wire carries a typical household current of 1.50 A (in one direction) at a location where the earth's magnetic field is 0.550 gauss from south to north.
*I know there's a lot of questions, but I will rate the you-know-what out of you
a) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from west to east.
b) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from west to east.
c) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running vertically upward.
d) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running vertically upward.
e) Find the direction of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from north to south.
f) Find the magnitude of the force that our planet's magnetic field exerts on this cord if is oriented so that the current in it is running from north to south.
g) Is the magnetic force ever large enough to cause significant effects under normal household conditions?
If the current is running from west to east, then the direction of the force that our planet's magnetic field exerts on the cord is from south to north directions and The magnitude of the magnetic force is about 0.825 Newtons.
What are the magnetic force?If the current is running from west to east, then the direction of the force that our planet's magnetic field exerts on the cord is from south to north. The magnitude of the force is given by the equation F = B × I × L, where B is the magnetic field strength, I is the current, and L is the length of the wire. In this case, the magnitude of the force is 0.825 N.
If the current is running vertically upward, then the direction of the force that our planet's magnetic field exerts on the cord is from east to west.
The magnitude of the force is again given by the equation F = B × I × L, so the magnitude of the force is 0.825 N.
If the current is running from north to south, then the direction of the force that our planet's magnetic field exerts on the cord is from west to east.
The magnitude of the force is again 0.825 N. The magnetic force is not large enough to cause significant effects under normal household conditions.
Learn more about Magnetic force here:
https://brainly.com/question/3160109
#SPJ11
Predict how the horizontal component of the velocity will change with time after the projectile is fired.
A) It stays constant. B) It continuously decreases. C) It continuously increases. D) It first increases and then decreases. E) It first decreases and then increases.
The correct option is option A) It stays constant.The horizontal component of the velocity will remain constant with time after the projectile is fired.
Projectile motion is the movement of an object that has been thrown, launched, or shot into the air. The object is called a projectile, and its path is referred to as its trajectory. Projectile motion can be predicted and analyzed by physics, but it is not as straightforward as it may seem. The following are some of the properties of projectile motion: Acceleration due to gravity (9.8 m/s²) Act of the horizontal and vertical components of velocity (v) Path of the projectile in a parabolic shape. The horizontal component of the velocity will remain constant with time after the projectile is fired.
Learn more about projectile and velocity at: https://brainly.com/question/14478315
#SPJ11
if a basketball and a medicine ball are dropped from the same height at the same time, without air resistance, which ball would land first? explain
Without air resistance, both the basketball and the medicine ball will fall at the same rate and reach the ground at the same time. This is due to the fact that gravity affects objects the same, regardless of their mass.
Why would the basketball fall first?When a ball is dropped from a height, the only force acting upon it is gravity. Gravity pulls each ball with the same force; however, the ball with more mass will have more gravitational potential energy than the other. It means the basketball will have more potential energy to convert to kinetic energy during the fall, making it faster than the medicine ball.
Thus, in conclusion, the basketball would fall first as it is more massive than the medicine ball.
When a basketball and a medicine ball are dropped from the same height at the same time without air resistance, the basketball would land first. The explanation for this is due to the size and weight of each ball.
Basketball is heavier than the medicine ball, and both have the same height to fall. The more massive the object, the more gravitational pull it experiences, and thus, it falls faster. So, the basketball would land first if a basketball and a medicine ball are dropped from the same height at the same time without air resistance.
Read more about mass here:
https://brainly.com/question/19385703
#SPJ11
An 8 kg ball travelling at 4 m/s collides head on with a 3 kg ball travelling at 14 m/s. The balls bounce off each other and travel back the way they came. The 8 kg ball travels away at 2 m/s. calcukate: the velocity of the 3 kg ball after the collision.
The velocity of the 3 kg ball after collision with the 8 kg ball is 2 m/s.
What is velocity?Velocity is the rate of change of displacement.
To calculate the velocity of the of the 3 kg ball after collision, we use the formula below.
Formula:
MU+mu = MV+mv................... Equation 1Where:
M = Mass of the bigger ballm = Mass of the smaller ballU = Initial velocity of the bigger ballu = Initial velocity of the smaller ballV = Final velocity of the bigger ballv = Final velocity of the smaller ballFrom the question,
Assuming: The bigger ball is initial traveling to the right and lets take right to be positive.
Given:
M = 8 kgm = 3 kgU = 4 m/su = -14 m/sV = - 3 m/sSubstitute these values into equation 1 and solve for v
(8×4)+(-14×3) = (-2×8)+(3×v)32-42 = -16+3v3v = -10+163v = 6v = 6/3v = 2 m/sHence, the velocity of the 3 kg ball is 2 m/s.
Learn more about velocity here: https://brainly.com/question/24445340
#SPJ1
the eoq model is most relevant for which one of the following?
inventory management, the eoq model is most relevant for inventory management. In order to reduce the overall cost of inventory, it helps to determine the ideal order quantity that a business should produce or buy.
In operations and inventory management, the EOQ (Economic Order Quantity) model is a widely used mathematical model. In order to reduce the overall cost of inventory, it helps to determine the ideal order quantity that a business should produce or buy. The most cost-effective order quantity is determined by the model, which takes into account a variety of inventory costs, including ordering, holding, and stock-out costs. The EOQ model enables businesses to maintain suitable inventory levels while reducing inventory costs. As a result, it is a crucial tool for any company that manages inventory, from manufacturing to retail.
learn more about inventory management here:
https://brainly.com/question/4310633
#SPJ4
The warming of a car in the sun is an excellent analogy for the greenhouse effect of our atmosphere. Complete the analogy with the words and phrases then place the sentences in order. Drag the text blocks below into their correct order. visible light с The car windows allow and infrared radiation to pass into the car. Similarly, our atmosphere allows infrared radiation and to pass through. none polar ice caps The car's interior, like the Earth's absorbs and infrared radiation then emits infrared radiation back out.
The car's interior, like the Earth's, absorbs visible light and infrared radiation, then emits infrared radiation back out.
c. Visible light and infrared rays can enter the car through the windows. Similar to how visible light and infrared radiation can pass through our atmosphere. a. Similar to how a car's exterior reflects some incoming radiation, the polar ice caps do the same. b. Just like the Earth, the interior of the car collects visible light and infrared radiation before reemitting it. d. The automobile gets hotter since none of the radiation can get through the windows. Similar to how part of the radiation that the Earth emits is trapped in the atmosphere, global warming results.
Order correctly: Visible light and infrared radiation can enter the car through the windows.
Learn more about car here:
https://brainly.com/question/11733094
#SPJ4
(Astronomy)
If humans one day encountered aliens, what measurement system would we most likely share with them?
light speed
parsecs
astronomical unit
miles
ANSWER: A (Light speed.)
Answer:
If humans one day encountered aliens, it is unlikely that we would share any existing measurement system with them. Different civilizations could have different systems of measurement and it would be necessary to establish a common framework to facilitate communication and understanding. However, scientists have proposed the use of mathematical constants and physical properties of the universe as a basis for a universal system of measurement that could be shared by any intelligent species, such as the speed of light, the Planck length, and the gravitational constant.
A pendulum comprised of a metal ball attached to a light string of length L undergoes simple harmonic motion with a period given by
T = 2 π sqrt(L/g). If the ball is made positively charged and the pendulum is swung in an electric directed towards the center of the earth. Which statement is true?
Not enough information
The period is unchanged
The period decreases
The period increases
Not enough information is given to determine whether the period would decrease, increase, or remain unchanged.
The period indicates the time required for a complete oscillation, the frequency indicates the number of oscillations that occur in one second, and the angular frequency indicates the magnitude of the rotational speed.
The period of a pendulum comprised of a metal ball attached to a light string of length L undergoing simple harmonic motion is given by T = 2 π sqrt(L/g). If the ball is made positively charged and the pendulum is swung in an electric directed towards the center of the earth, then not enough information is given to determine whether the period would decrease, increase, or remain unchanged.
Learn more about The period of a pendulum: brainly.com/question/11746625
#SPJ11
you have an rc circuit with a time constant of 5.35 s. if the total resistance in the circuit is 231.2 k , what is the capacitance of the circuit (in f)? don't type the units into the answer box.
The capacitance of the circuit (in f) is 2.31×10⁻⁵F for the rc circuit with a time constant of 5.35 s. if the total resistance in the circuit is 231.2 k.
What is the capacitance of the circuit?The capacitance of an RC circuit can be calculated using the equation C = τ/(R), where τ is the time constant, R is the total resistance, and C is the capacitance. For this RC circuit, the time constant is 5.35s and the total resistance is 231.2 k. Therefore, the capacitance is 5.35s/(231.2k) = 2.31×10⁻⁵F.
Time constant of the RC circuit, τ = 5.35s
Total resistance in the circuit, R = 231.2 kΩ = 231200 Ω
Capacitance of the circuit = ?
We know that, Time constant (τ) of a RC circuit = R × C.
where, R is the resistance in ohms, C is the capacitance in farads. Substitute the given values in the above equation:
τ = RC
5.35 s = R × C231200 Ω × C = 5.35 s
C = 5.35 s / 231200 Ω
C = 2.31 × 10⁻⁸ F.
Therefore, the capacitance of the circuit is 2.31 × 10⁻⁸ F.
Read more about circuit :
https://brainly.com/question/26064065
#SPJ11
5
Read the following sentences:
In those early games, balls and bats were often homemade. Anyone who
used a glove or mask was called a sissy. How would you like to squat
behind home plate with no glove or catcher's mask and have the ball
whiz toward you?
From this textual evidence, which viewpoint seems closest to what the article's
author likely believes?
A The changes in rules regarding safety in baseball over the years have been
an improvement.
B The changes in rules regarding safety in baseball over the years have not
made the game safer.
C
The changes in rules regarding safety in baseball over the years have had
no effect.
D The changes in rules regarding safety in baseball over the years may
be eliminated.
A shell is shot with an initial velocity, v0 of 20m/s,at an angle of θ0= 60 with the horizontal. At thetop of the trajectory, the shell explodes into two fragments ofequal mass. One fragment, whose speed immediately after theexolosion is zero, falls vertically. How far from the gun does theother fragment land, assuming that the terrain is level and thatair drag is negligible?
When the shell is shot with an initial velocity 20m/s with angle 60 the distance d the other fragment lands from the gun is 69.3 m.
The other fragment will land a distance d away from the gun, where d is determined by the initial velocity, v₀ of 20 m/s and the angle, θ₀ of 60°, from which the shell was launched. The trajectory of the fragment is affected by the shell's velocity, its gravitational potential energy, and its kinetic energy. When the shell explodes, it releases all of its kinetic energy, which is shared among the two fragments. The other fragment will travel a distance d which is determined by the total energy, E and its initial velocity, v0.
To calculate d, we can use the equation:
d = (2E/m)1/2sin(2θ₀) / v₀,
where m is the mass of the fragment and E is the total energy.
Therefore, the distance d the other fragment lands from the gun is given by: d = (2E/m)1/2sin(2θ₀) / v₀
= (2×202×sin(120°))/20
= 40×sin(120°) = 40×√3 = 69.3 m.
Learn more about trajectory and velocity at : https://brainly.com/question/13164047
#SPJ11
A nonrelativistic electron and a nonrelativistic proton have the same de Broglie wavelength. Which of the following statements about these particles are accurate? (There may be more than one correct choice.). A) Both particles have the some speed. b) Both particles have the some kinitic energy c) the electron has more kinetic energy than the proton. d) the electron has more momentum than the proton. e) Both particles have the some momentum
For a nonrelativistic electron and a nonrelativistic proton having the same de Broglie wavelength, we can say that: both particles have the same speed and both particles have the same momentum. The correct answers are Option A and E.
The de Broglie wavelength is defined as the wavelength of a particle, which is associated with its momentum. It is given by,
λ = h / p
where λ is the de Broglie wavelength, h is the Planck's constant and p is the momentum of the particle.
Therefore, if a nonrelativistic electron and a nonrelativistic proton have the same de Broglie wavelength, they must have the same momentum. This is because the momentum of the particle is inversely proportional to its wavelength.
The formula for the kinetic energy of a particle is given by,
K.E. = p² / 2m
where K.E. is the kinetic energy of the particle, p is the momentum of the particle and m is the mass of the particle.
Since the momentum of the electron and the proton is the same, the kinetic energy of the electron and the proton will depend on their mass. Therefore, it can be concluded that the electron will have more kinetic energy than the proton because the mass of the electron is much smaller than the mass of the proton.
Learn more about De Broglie theory here: https://brainly.com/question/20372425
#SPJ11
A car moves with this distance vs time function: 5 = 2t^2 + 2. what is the acceleration rate of the car? (clue: use derivatives) answer with number only, e.g. if it's 6t m/s^2, just write 6t
Answer:
just write 6t and the same
a big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table. initially the block is at the top of the incline at rest. determine the speed of the block at the bottom of the incline
When the big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table, the speed of the block at the bottom of the incline is 3.14 m/s.
Given that
Mass of the block, m = 10 kg.
Angle of inclination, θ = 30°
Initial velocity, u = 0.
Frictional force, f = 0.
Using the formula for gravitational force, F = mg
where, g = 9.8 m/s² (acceleration due to gravity)
F = mg= 10 kg × 9.8 m/s²= 98 N
The component of gravitational force that acts parallel to the incline, Fsinθ is responsible for the acceleration of the block. Fsinθ = ma; Where a is the acceleration of the block.
a= (98 N)sin 30° / 10 kg= 4.9 m/s²
Using the formula for speed, v = u + at where,
u = initial velocity = 0m/s
t = time taken = time taken to slide from top to bottom of the incline.= √(2h/g) where,
h = height of the incline = 2 m (since the mass is at rest initially at the top of the incline).
Therefore, t = √(2 × 2 m / 9.8 m/s²)= 0.64 s
Substituting the values in the above formula, v = u + at= 0 + (4.9 m/s² × 0.64 s)= 3.14 m/s.
To know more about speed, refer here:
https://brainly.com/question/29309579#
SPJ11#
a rectangular field is twice as long as it is wide. the perimeter of the field is 450 yards. find the dimensions of the field. you must find an equation to represent the situation and solve.
The dimensions of the field can be found to be 75 yards in width and 150 yards in length.
Given:
Let the width of the rectangular field be x
Length of the rectangular field = 2x
Perimeter of the rectangular field = 450 yards
Formula Used:
Perimeter of a rectangle = 2 (l + w)
Where l and w are the length and width of the rectangle respectively.
Solution:
As per the question,
Perimeter of the rectangular field = 450 yards
Therefore, 2(Length + Width) = 450
2(x + 2x) = 450
2(3x) = 450
6x = 450
x = 75
Therefore, the width of the rectangular field is 75 yards
Length of the rectangular field = 2x = 2 × 75 = 150 yards
Hence, the dimensions of the field are 75 yards by 150 yards.
To know more perimeter, refer here:
https://brainly.com/question/30252651#
#SPJ11
A gas is compressed at a constant pressure from a volume of 10 m3 to a volume of 4 m3 , then work done on the system is:
a) nRT ln 1/6
b) nRT In2/5
c) nRT In 5/2
d) nRT In 6
None of the answer options provided are correct as they all involve calculations that assume certain values for the pressure, volume, and temperature of the gas.
What is Constant Pressure?
Constant pressure is a thermodynamic process in which the pressure of a system remains constant during the process. This means that any change in volume or temperature of the system must be accompanied by a corresponding change in some other property, such as the amount of heat added or removed from the system.
Since the gas is compressed at a constant pressure, the work done on the system can be calculated as:
W = -PΔV
In this case, P is constant, so we have:
W = -P(V2 - V1)
W = -P(4 m^3 - 10 m^3)
W = -P(-6 m^3)
W = 6P m^3
Since we are not given any information about the type of gas or its properties, we cannot use the ideal gas law to calculate the pressure P. Therefore, we cannot determine the exact value of the work done on the system.
Learn more about Constant Pressure from given link
https://brainly.com/question/2139620
#SPJ1
Three engines operate between reservoirs separated in temperature by 300 K. The reservoir temperatures are as follows:Engine A: Th = 1000 K, Tc = 700 K;Engine B: Th = 800 K, Tc = 500 K;Engine C: Th = 600 K, Tc = 300 K.Rank the engines in order of theoretically possible efficiency, from highest to lowest.
The order of theoretically possible efficiency, from highest to lowest is Engine C, Engine B, and Engine A.
The theoretical efficiency of a Carnot engine is given by the formula:
Efficiency = 1 - T_{c} / Th
where Th and T_{c} are the temperatures of the hot and cold reservoirs, respectively.
Using this formula, we can calculate the efficiency of each engine.
For engine A, we have:
Efficiency = 1 - T_{c} / Th = 1 - 700 K / 1000 K = 0.3 or 30%
For engine B, we have:
Efficiency = 1 - T_{c} / Th = 1 - 500 K / 800 K = 0.375 or 37.5%
For engine C, we have:
Efficiency = 1 - T_{c} / Th = 1 - 300 K / 600 K = 0.5 or 50%
Therefore, the ranking of engines from highest to lowest theoretical efficiency is: Engine C (50%) > Engine B (37.5%) > Engine A (30%)
To practice more questions about theoretical efficiency:
https://brainly.com/question/29339898
#SPJ11
what complication is introduced in the excerpt? marco is unable to locate his friends in the busy park. the slide’s very long, uniformly charged cylinder have radius R and linear charge density λ.
a. Find the cylinder's electric field strength outside the cylinder, r≥R. Give your answer as a multiple of λϵ0.
Express your answer in terms of some or all of the variables R,r, and the constant II
b. Find the cylinder's electric field strength inside the cylinder, r≤R. Give your answer as a multiple of λϵ0.
Express your answer in terms of some or all of the variables R,r and the constant II
a. To find the electric field strength outside the cylinder, E = λ/(2πϵ0r), where r≥R. b. To find the electric field strength inside the cylinder, E = λr/(2πϵ0R^2), where r≤R.
the electric field strength inside and outside a charged cylinder can be determined using the formulas E = λr/2πϵ0R^2 and E = λ/2πϵ0r, respectively. The electric field strength outside the cylinder is proportional to the linear charge density and inversely proportional to the distance from the center of the cylinder. On the other hand, the electric field strength inside the cylinder is proportional to both the linear charge density and the distance from the center of the cylinder, the slide’s very long, uniformly charged cylinder have radius R and linear charge density λ. a. Find the cylinder's electric field strength outside the cylinder, r≥R. but inversely proportional to the square of the radius of the cylinder. These formulas can be used to solve problems involving charged cylinders and their electric fields.
learn more about electric field strength here:
https://brainly.com/question/28227168
#SPJ4
A polarized light is incident on several polarizing disks whose planes are parallel and centered on common axis. Suppose that the transmission axis of the first polarizer is rotated 19 relative to the axis of polarization of the incident îight and tat î e ư n miss on aus of each additional analyzer is rotated 19° relative to the transmission axis of the previous one. What is the minimum number of polarizer needed whole number), so the transmitted light through all polarizing sheets has an intensity that is less than 18% that striking the first polarizer?
The minimum number of polarizers required to make the transmitted light through all the polarizing sheets have an intensity that is less than 18% of that striking the first polarizer is four.
Using Malus' Law, determine the intensity of light transmitted through a polarizer that is rotated at an angle θ relative to the incident polarization of the light.
Malus' Law: I = I₀cos²θ, Where, I₀ is the initial intensity of the light and θ is the angle of rotation.
Calculate the light intensity transmitted through each polarizer.
I₀ = Intensity of polarized light incident on the first polarizer = 100% = 1
I = I₀ cos²19° = 0.818 I₀
I = I cos²19° = 0.667 I₀
I = I cos²19° = 0.544 I₀
I = I cos²19° = 0.443 I₀
I = 0.18 I₀, where I is the intensity of the transmitted light
Determine the minimum number of polarizers required.The transmitted light has an intensity of 18% of that striking the first polarizer. Since the intensity of transmitted light is reduced to 18% after the fourth polarizer, the minimum number of polarizers needed is 4.
Therefore, the minimum number of polarizers required to make the transmitted light through all the polarizing sheets have an intensity that is less than 18% of that striking the first polarizer is four.
Learn more about "polarizers" at : https://brainly.com/question/16106487
#SPJ11
what is the main factor to consider when planning your vessel’s approach to a dock where you intend to tie up?
Wind direction and speed, together with current, tides, vessel maneuverability, and the appropriate angle and speed, are the key factors to take into account when approaching a dock for a tie-up.
The wind's direction and speed, together with the current, tides, and the vessel's maneuverability, are the key factors to take into account when preparing a vessel's approach to a dock where you wish to tie up. To guarantee a secure tie-up, it is essential to approach the dock at the right angle and speed while taking these considerations into mind. The size and design of the dock, its height above the water, and the availability of mooring lines and fenders are also additional crucial factors. A good tie-up can also be attributed to effective communication and cooperation between the crew and any other people on the dock.
learn more about vessel maneuverability here:
https://brainly.com/question/4197253
#SPJ4
a 25.0-kg dog is trapped on a rock in the middle of a narrow river. a 66.0-kg rescuer has assembled a swing with negligible mass that she will use to swing down and catch the trapped dog at the bottom of her swing, and then continue swinging to the other side of the river. the ledge that the rescuer swings from is 5.0 m above the rock, which is not high enough so the rescuer and dog together can reach the other side of the river, which is 3.0 m above the rock. however, the rescuer can use a ladder to increase the height from which she swings. what is the minimum height of the ladder the rescuer must use so both dog and rescuer make it to the other side of the river? assume that friction and air resistance are negligible. show your work in the space below.
The minimum height of the ladder needed by the rescuer for a successful rescue of the dog is 5.944 meters
How to determine minimum height?To determine the minimum height of the ladder required for the rescuer and the dog to reach the other side of the river, use the conservation of energy principle. At the highest point of the swing, all of the gravitational potential energy of the system is converted into kinetic energy. At the lowest point of the swing, all of the kinetic energy is converted back into gravitational potential energy.
Let h be the height of the ladder above the rock where the swing is attached. Let v be the speed of the rescuer and the dog at the bottom of the swing, and let g be the acceleration due to gravity. Then, the conservation of energy equation is:
m_rgh + m_dgh = (m_r + m_d)gh' + (m_r + m_d)v²/2
where m_r and m_d are the masses of the rescuer and the dog, respectively, and h' is the height of the other side of the river.
We can solve for h' by rearranging the equation:
h' = [(m_r + m_d)gh + (m_r + m_d)v²/2 - m_rgh - m_dgh]/(m_r + m_d)
Substituting the given values:
h' = [(66.0 kg + 25.0 kg) × 9.81 m/s² × 5.0 m + (66.0 kg + 25.0 kg) × v²/2 - 66.0 kg × 9.81 m/s² × 5.0 m - 25.0 kg × 9.81 m/s² × 5.0 m]/(66.0 kg + 25.0 kg)
Simplifying the equation:
h' = (305.145 + 91.8725 - 323.46 - 122.625)/91 = 0.944 m
Therefore, the minimum height of the ladder that the rescuer must use is:
h - 5.0 m = 0.944 m
h = 5.944 m
So, the rescuer must use a ladder that is at least 5.944 meters high to swing over to the other side of the river with the dog.
Learn more on minimum height here: https://brainly.com/question/16672497
#SPJ1
p55. a 0.900 v potential difference is maintained across a 1.50 m length of tungsten wire that has a cross-sectional area of 0.600 mm . what is the2 current in the wire?
The current in the wire when a 0.900 V potential difference is maintained across a 1.50 m length of tungsten wire that has a cross-sectional area of 0.600 mm² can be calculated using Ohm's Law. The current through the wire is 0.643 A.
What is Ohm's Law?Ohm's law states that the current through a conductor between two points is directly proportional to the voltage across the two points. Introducing the constant of proportionality, the resistance, one arrives at the usual mathematical equation that describes this relationship:
I = V/R
where:
I is the current through the conductor in units of amperes, V is the potential difference measured across the conductor in units of volts,R is the resistance of the conductor in units of ohms.I = V/RI = (0.9 V)/(R)
The resistivity of tungsten is given by 5.6 x 10⁻⁸ Ωm.The formula for the resistance of the wire is given by
R = (ρL)/AR = [(5.6 x 10⁻⁸ Ωm) (1.5 m)]/(0.6 mm²)The resistance of the wire is 1.4 Ω.I = V/RI = (0.9 V)/(1.4 Ω)
The current through the wire is 0.643 A.
Learn more about Ohm's Law: https://brainly.com/question/14296509
#SPJ11
A dragster is travelling east when the parachute opens and slows the dragster for 4.5 seconds at a rate of 10 m/s2 west. What was the dragster's change in velocity due to the parachute?
The dragster's change in velocity due to the parachute can be calculated using the kinematic equation:
Δv = aΔt
where Δv is the change in velocity, a is the acceleration, and Δt is the time interval during which the acceleration occurs. In this case, the dragster is initially travelling east, so its velocity is positive, and the parachute applies a force in the opposite direction, resulting in a negative acceleration.
Given that the acceleration is -10 m/s² (westward) and the time interval is 4.5 seconds, we can calculate the change in velocity as:
Δv = (-10 m/s²) x (4.5 s) = -45 m/s
Therefore, the dragster's change in velocity due to the parachute is -45 m/s (westward). This means that the dragster's velocity is reduced by 45 m/s in the westward direction over the 4.5-second interval during which the parachute is deployed.
To know more about velocity , visit :
https://brainly.com/question/17127206
#SPJ1
The change in velocity due to the parachute is -45 m/s east
What is velocity ?
Velocity is a vector quantity that describes the speed and direction of motion of an object. In other words, velocity is the rate at which an object changes its position in a specific direction.
Velocity is expressed in units of distance per time, such as meters per second (m/s) or kilometers per hour (km/h)
Velocity is different from speed, which is also a measure of the rate of motion but only describes how fast an object is moving, without taking into account the direction of motion.
we will use the formula :-
change in velocity = acceleration x time
where acceleration is the rate at which the dragster slows down, and time is the duration for which it slows down.
Here, the dragster is travelling east, and the parachute applies a force in the opposite direction (west), causing it to slow down. So, the acceleration is -10 m/s^2 (negative because it's in the opposite direction to the velocity).
The time for which the dragster slows down is 4.5 seconds.
Therefore, the change in velocity due to the parachute is:
change in velocity = acceleration x time
change in velocity = (-10 m/s^2) x (4.5 s)
change in velocity = -45 m/s east
Note that the velocity is negative because the dragster is slowing down, and it's still travelling east (i.e., in the positive direction).
To know more about velocity visit :-
https://brainly.com/question/80295
#SPJ1
5. (10 pts) The shedding frequency based on the analysis of Question 3 is to be determined through the use of a small-scale model to be tested in a water tunnel. For the specific bridge structure of interestD=20 cmandH=300 cm, and the wind speedVis25 m/s. Assume the air is at MSL ISA conditions. For the model, assume that D m=2 cm. (a) Determine the length of the model Hm needed for geometric scaling. (b) Determine the flow velocity Vm needed for Reynolds number scaling. (c) If the shedding frequency for the model is found to be 27 Hz, what is the corresponding frequency for the full-scale structural component of the bridge? Notes: Refer to the eBook for the properties of air. Assume the density of water rho H2O= 1000 kg/m3 and the dynamic viscosity of water μ H2O=1×10^−3 kg/m/s.
Length of the model Hm = 12 cm. The flow velocity Vm = 5 m/s. Frekuensi yang sesuai untuk skala penuh komponen struktural jembatan adalah 2,7 Hz.
To determine the length of the model, Hm, for geometric scaling, you must use the relationship Hm/H = Dm/D, where Dm is the model's diameter, D is the full scale structure's diameter, and Hm and H are the model and full-scale heights, respectively. Substituting in the given values, we have Hm/300 cm = 2 cm/20 cm, which can be solved for Hm to find that Hm = 12 cm.
To determine the flow velocity Vm for Reynolds number scaling, you must use the relationship Vm/V = sqrt(rhoH2O/rho)*(D/Dm), where rho is the air density and rhoH2O is the water density. Substituting in the given values, we have Vm/25 m/s = sqrt(1000 kg/m3/1.225 kg/m3)*(20 cm/2 cm). Solving for Vm, we find that Vm = 5 m/s.
To determine the shedding frequency for the full-scale structure of the bridge, we must use the relationship f/fmodel = (Vmodel/V)*(Dmodel/D). Substituting in the given values, we have f/27 Hz = (5 m/s/25 m/s)*(2 cm/20 cm). Solving for f, we find that the corresponding frequency for the full-scale structural component of the bridge is 2.7 Hz.
Learn more about the flow velocity: brainly.com/question/28595543
#SPJ11
a bullet is shot horizontally from shoulder height (1.2 m) with an initial speed of 682 m/s. (a) how much time elapses (in s) before the bullet hits the ground? s (b) how far does the bullet travel horizontally (in m)? m
A bullet is shot horizontally from shoulder height (1.2 m) with an initial speed of 682 m/s.
The kinematic equation of motion for the horizontal motion of an object
i.e, s = vt
Where s is the displacement,
v is the initial speed,
and t is the time.
(a) Initial vertical velocity (u) = 0 m/s
Acceleration (a) g = 9.8 m/s²
(since the bullet is moving vertically downwards)
Vertical displacement (s)H = 1.2 m
By using the following kinematic equation of motion: v² = u² + 2as
Putting the values in the above equation,
0² = 682² + 2 (-9.8) (1.2)
s = 47.999m
since the bullet will hit the ground at 48 m.
Therefore, the time taken by the bullet to hit the ground is given by the
s = ut + 1/2 a t²
Hence, 48 = 0 × t + 1/2 (9.8) t²
t = 3.91 seconds.
(b) horizontal velocity (u) = 682 m/s
Time (t) = 3.91 seconds.
By using the following kinematic equation of motion:
s = ut
Putting the values in the above equation,
s = 682 × 3.91s
= 2668.62m
Thus, the bullet will travel a distance of 2668.62 m.
Learn more about bullet speed at:
https://brainly.com/question/12875382
#SPJ11
In order to join more than two datasets with only visual recipes, which of the following solutions is correct and why? It is not possible to join more than two datasets at a time with the Join recipe. Perform multiple Join recipes instead. Although only two datasets can be added in the Join recipe creation dialog, more datasets can be added on the Join step. Provided it is a left join, a single Join processor of the Prepare recipe is capable of joining more than two datasets at a time. None of these.
The correct solution is "Perform multiple Join recipes instead." It is not possible to join more than two datasets at a time with the Join recipe. Each Join recipe can only join two datasets at a time. To join more than two datasets, multiple Join recipes should be used in sequence.
When joining more than two datasets with visual recipes, it is possible to perform multiple Join recipes instead of joining all of them together at once. This is because the Join recipe only allows for the addition of two datasets at a time during the creation dialog, but more datasets can be added on the Join step.For instance, if there are four datasets to be joined, the first two can be joined together using the Join recipe. Then, the resulting dataset can be joined with the third dataset, followed by joining the resulting dataset with the fourth dataset. This way, all four datasets can be joined together.There is a possibility of using a single Join processor of the Prepare recipe for joining more than two datasets at a time, but only if it is a left join. However, this method is not advisable as it may result in inaccuracies and inconsistencies.The Join recipe is a recipe that enables the merging of two datasets into a single dataset based on a shared column. This recipe is useful for cleaning and integrating data from different sources into a single dataset. The Join recipe allows for the selection of the type of join to perform, such as inner join, left join, right join, and full outer join.The Prepare recipe is a recipe that is used to transform and clean datasets in preparation for analysis. This recipe allows for the selection of processors that carry out various functions such as renaming columns, filtering rows, and calculating new columns.
For mroe such questions on Datasets
https://brainly.com/question/4219149
#SPJ11
suppose the car, traveling at 25 m/s is rounding this flat curve with highest possible speed for the conditions of the road, to stay on the circle without sliding out to a greater radius. what is the coefficient of static friction between its tires and the ground?
The coefficient of static friction between its tires and the ground is 0.80.
To determine the coefficient of static friction between its tires and the ground, we can use the expression for the coefficient of static friction given by;
μ_s = (g * tanθ) / (1 - (v²/r²))
Where;
μ_s = Coefficient of static friction
g = Acceleration due to gravity
θ = Angle of banking
r = Radius of the curve
v = Velocity of the vehicle
Substitute g = 9.8 m/s², θ = 0°, r = 100 m, and v = 25 m/s in the above expression.
μ_s = (9.8 * tan0) / (1 - (25²/100²))
μ_s = 0.80
Hence, the coefficient of static friction is 0.80.
Learn more about coefficient of static friction here: https://brainly.com/question/25050131.
#SPJ11
A 1500 kg car is moving to the right with a speed of 20.0 m/s when it collides with a wall and reboubds at a speed of 5.00 m/s.
If the collision lasts for 250 ms, then the magnitude of the average force acring on the car is _____ kN (the answer is 150 but I'm not sure how)
pls help!!
Answer:
See below.
Explanation:
When the 1500 kg car collides with the wall and rebounds at a speed of 5.00 m/s, we can calculate the change in the car's velocity using the following formula:
Δv = v2 - v1
Where Δv is the change in velocity, v2 is the final velocity, and v1 is the initial velocity. Substituting the given values, we get:
Δv = 5.00 m/s - 20.0 m/s
Δv = -15.0 m/s
The negative sign indicates that the direction of the car's velocity has reversed, or that the car is now moving to the left. To calculate the magnitude of the change in velocity, we take the absolute value:
|Δv| = |-15.0 m/s|
|Δv| = 15.0 m/s
Therefore, the magnitude of the change in velocity is 15.0 m/s.
Now,
To find the magnitude of the average force acting on the car during the collision, we can use the impulse-momentum theorem, which states that:
Impulse = change in momentum
Average force = Impulse / time
The change in momentum of the car is given by:
Δp = mΔv
where Δv is the change in velocity calculated in the previous answer and m is the mass of the car.
Δp = 1500 kg × (-15.0 m/s)
Δp = -22500 kg·m/s
The impulse acting on the car during the collision is equal to the change in momentum:
Impulse = Δp = -22500 kg·m/s
To find the magnitude of the average force acting on the car during the 250 ms collision, we divide the impulse by the duration of the collision:
Average force = Impulse / time
Average force = -22500 kg·m/s / 0.250 s
Average force ≈ -90,000 N
The negative sign indicates that the force is in the opposite direction of the car's motion, or to the left. Therefore, the magnitude of the average force acting on the car during the collision is approximately 90,000 N.
A current is set up in a wire loop consisting of a semicircle of radius 4.00 cm, a smaller concentric semicircle, and two radial straight lengths, all in the same plane. Figure shows the arrangement but is not drawn to scale. The magnitude of the magnetic field produced at the center of curvature is 47.25μT.The smaller semicircle is then flipped over (rotated) until the loop is again entirely in the same plane. The magnetic field produced at the (same) center of curvature now has magnitude 15.75μT, and its direction is reversed from the initial magnetic field. What is the radius of the smaller semicircle?
The radius of the smaller semicircle is 2cm.
[tex]B_1= \frac{u0I}{T} (\frac{1}{R_1} -\frac{1}{R_2} )[/tex]
[tex]B_2= 2.\frac{u0I}{2} \frac{1}{R_2} =\frac{uoI}{R_2}[/tex]
We can now solve for r by setting $B_1=-B_2
[tex]\frac{u0I}{2} (\frac{1}{4} -\frac{1}{r} )= \frac{uoI}{r}[/tex]
r= 2cm
A magnetic field is a force field that is created by moving electric charges. It is a fundamental concept in electromagnetism, and it is essential for many technologies, such as motors, generators, and MRI machines.
A magnetic field is typically represented by lines of magnetic flux that show the direction of the force. These lines of flux are generated by electric currents, whether they are moving charges or stationary ones. The strength of a magnetic field is measured in units of teslas or gauss, depending on the system of measurement used.
Magnetic fields have both magnitude and direction and can interact with other magnetic fields or with magnetic materials, such as iron or steel. The interaction between magnetic fields and moving charges can cause the charges to change direction, which is the basis for motors and generators.
To learn more about Magnetic field visit here:
brainly.com/question/14848188
#SPJ4
suppose that one particle of the flow approaches a plate of a capacitor. explain what happens to the other plate of the capacitor?
The other plate of the capacitor is induced with an opposite charge through electrostatic induction as the particle of the flow approaches one plate.
As the particle of the flow approaches one plate of the capacitor, it induces an opposite charge on the other plate of the capacitor through the process of electrostatic induction. The electric field produced by the charge on the approaching plate pushes the electrons on the other plate away from the approaching plate, resulting in an accumulation of charge of the opposite sign on the other plate.
This process continues until the potential difference between the plates becomes large enough to produce a discharge, after which the process of electrostatic induction ceases. The discharge may occur in the form of a spark or a breakdown of the dielectric material separating the plates, depending on the strength of the electric field and the dielectric strength of the material.
Overall, the other plate of the capacitor experiences a temporary polarization and a buildup of charge of the opposite sign due to the approaching particle.
To know more about capacitor, refer here:
https://brainly.com/question/30889004#
#SPJ11