The acceleration of block A is 8.4949 and block B is 4.2475 ft/s² while the tension is the cable is 121.168 lb.
What is tension?When there are two forces acting on the ends of a cable, rope, wire, or string, it is said to be under tension. The cable has a one-direction pull along its entire length, pulling equally in both directions on objects at either end.
Tension can also be used to describe the forces that are acting on both ends of the two elements. In other words, tension's polar opposite is compression.
Physical objects must exert some force on one another in order to make contact with one another. Depending on the kind of object, each of these contact forces will be unique.
Take a section about the rope near block B and using the show datum
SB + (SB - SA) = l
2SB - SA = l
2SB - SA = 0
2aB - aA = 0
aA = 2aB
Take FBD of block-A
(Upward+) ∑Fₓ = mAaA
T - W[tex]_A[/tex]sin20° = mAaA
T - 200sin20° = (W[tex]_A[/tex]/g)(2aB)
T = 200sin20° + (W[tex]_A[/tex]/g)(2aB)
Take FBD of block-B;
(Downward+) ∑Fₓ = mBaB
W[tex]_B[/tex]cos20° - 2T = mAaA
300cos20° - 2(200sin20° + (W[tex]_A[/tex]/g)(2aB)) = (W[tex]_B[/tex]/g)(a[tex]_B[/tex])
300cos20° - 2(200sin20° + (200/32.2)(2aB)) = (300/32.2)(a[tex]_B[/tex])
a[tex]_B[/tex] = 4.2475 ft/s²
Acceleration of A is given as;
⇒ aA = 2aB
⇒ aA = 8.4949 ft/s²
Tension is given as;
T = 200sin20° + (200/32.2)(2(4.2475))
T = 121.168 lb
Thus, the acceleration of block A is 8.4949 and block B is 4.2475 ft/s² while the tension is the cable is 121.168 lb.
Learn more about tension
https://brainly.com/question/11348644
#SPJ4
These types of contaminants can be result from welding, cleaning or painting:
Welding fumes can cause serious health problems for workers if inhaled, according to OSHA.
Is smoke from welding harmful?Short-term exposure may cause nausea, lightheadedness, or irritation of the eyes, nose, and throat. Long-term inhalation of welding fumes can cause renal and nervous system damage as well as lung, throat, and urinary tract cancer. UV radiation and metal fume exposure are two health risks associated with welding, cutting, and brazing procedures. The risks associated with these procedures include burns, eye injury, electrical shock, wounds, and toe and finger crushing. Additionally, welding emits fumes. When heated metal vapours cool and condense into extremely minute particles, which remain suspended in the vapour or the gas, fumes are produced. The particles, which are frequently smaller than one micrometre (one-fiftieth the width of a human hair), may be made of metal or metal compounds.To learn more about harmful refer to:
https://brainly.com/question/17143947
#SPJ4
3 1 point Categorize the processes below as redow or acid/base
Categorize the processes of Redox reaction and ACID/BASE ( r x n)
The processes of Redox reaction are
digestion of gold in Aqua Regia
photosynthesis
Disinfection of swimming pools with chlorine
The processes Acid/base reaction are
stomach digestion
buffering of heart
burn with sodium citrate
Preparation of soup
The term "redox reaction" refers to the oxidation-reduction reaction that occurs on the surface of metals. This is the accumulation and transfer of electrons that occurs when two dissimilar atoms interact, most notably in ionic bonding. These two reactions happen at the same time and are known to be inseparable.
Acid–base reaction, a type of chemical process defines the exchange of one or more hydrogen ions, H +, between species that may be neutral (molecules such as water, H 2 O; or electrically charged (ions such as ammonium, NH 4+).
To learn more about redox or acid/base
https://brainly.com/question/15686955
#SPJ4
Fibonacci Sequence Submit + Continue New + Save Output Test Cases Docs Grade Assignment More Fibonacci.Java =
A Fibonacci series in Java is a sequence of numbers such that every third number is equal to the sum of the previous two numbers.
What is a Fibonacci series in Java?A number is entered into the Java Fibonacci recursion function. Because the Fibonacci sequence in Java begins with 0, 1, 1, the check is made for 0, 1, 2 and the result is 0, 1, 1. The function will call itself again if the argument n is greater than 3. The call is placed twice. Each number in the Fibonacci sequence, where 0 and 1 are the initial two numbers, is the sum of the two numbers that came before it. The first number in the Fibonacci sequence is.It goes from 0 to 1, 1, 2, 3, 5, 8, 13, 21, 34, 55, 89, 144, and so forth. The Financial Chart control from Component One Studio has built-in support for four different Fibonacci tools that can be used on a price or an indicator.To learn more about Fibonacci series refer to:
https://brainly.com/question/18369914
#SPJ4
n K-means clustering, the observations (data items) are evaluated to determine how many clusters exist within the data set.
K-means clustering is a method of clustering observations (data items) into groups (clusters) based on their similarity. The number of clusters is a user-specified parameter, typically denoted by "k".
How K-means clustering method works?The algorithm iteratively assigns each observation to the cluster with the nearest mean (center) until convergence, at which point the final cluster assignments are returned. The goal of K-means is to partition the observations into k clusters in which each observation belongs to the cluster with the nearest mean.
The goal is to minimize the distance between the observations and the cluster mean they are assigned to. The final cluster assignments and cluster means are returned as the output of the algorithm. It is widely used in data mining, machine learning and statistics.
To learn more about K-means clustering visit: https://brainly.com/question/14960630
#SPJ4
Technician A says that some people refer to the blower motor fan
as a squirrel fan. Technician B says that changing the blower fan
speed can be done by using a solenoid. Who is correct?
Tech A
Tech B
Both Techs A and B
ONeither Tech A nor B
Since Technician A says that some people refer to the blower motor fan as a squirrel fan. Technician B says that changing the blower fan speed can be done by using a solenoid. The correct option is option C: Both Techs A and B
What is the fan about?Some people refer to the blower motor fan as a "squirrel fan" because the fan blade is shaped like a squirrel cage. Technician A is correct in this statement.
Therefore, Changing the blower fan speed can be done by using a solenoid. This is an electromagnetic device that controls the flow of electrical current to the fan motor, which in turn controls the fan speed. Technician B is correct in this statement.
Learn more about solenoid from
https://brainly.com/question/1873362
#SPJ1
member abc, which is supported by a pin and bracket at c and a cable bd, was designed to support the 13-kn load p as shown. knowing that the ultimate load for cable bd is 100 kn, determine the factor of safety with respect to cable failure.
When transverse loadings are applied to a beam or frame, the axial force, normal force, or both may develop as internal forces.
The internal loads that result are c=Nc = -4.32 kip, V c=0.54 kip, and M c=2.16 kip. Ft Solution: The beam ab is supported by a cable BC and a pin at A. 120 I b/ft is the weight of the beam AB. 180 Ib/ft is the weight of the cable BC. Identify the loading at the beam's center AB (P ab). P ab = AB Beam Weight * AB Beam Length. For the weight of beam AB and its length of 12, substitute 120 I b/ft. Convert the unit from I b to kip using P ab=120*12 =1,440 I b. P ab = 1,440 I b*1,44 kip/1,000 I b. When transverse loadings are applied to a beam or frame, the axial force, normal force, or both may develop as internal forces.
Learn more about The internal loads here:
https://brainly.com/question/30187368
#SPJ4
Draw the shear and moment diagrams for the beam
Similar to shear diagrams, moment diagrams may be used to determine the position and magnitude of the greatest positive and negative moment, as well as the moment at any given place.
Using the areas of the regions in the shear-diagram allows you to create a moment-diagram quickly and easily. You must first answer the shear diagram and all of the reactions before proceeding.
Here is a member that has been solved to the appropriate state so that the moment diagram may be worked on. The current shear diagram is followed by the beginning of a moment diagram (M) (V).
Shear diagrams and moment diagrams both start and terminate at zero. The integral of each segment in the shear diagram is the moment in that region. Below are labels for the shear diagram's area regions, which will be used as references later.
Learn more about Shear here:
https://brainly.com/question/14418799
#SPJ4
4.
Describe the correct use of any equipment used to protect the health and safety of themselves and
their colleagues
Items like gloves, safety glasses, shoes, earplugs or muffs, hard helmets, respirators, or coveralls, vests, and full body suits are examples of personal protection equipment.
What equipment is are used for safety and protection?Wearing a safety helmet when using a power tool, donning the proper safety gear when dealing with chemicals, and taking all necessary measures when operating machinery are examples of the proper use of any equipment used to safeguard their health and the health of their coworkers.
Gloves, safety goggles, shoes, earplugs, respirators, hard hats, coveralls, vests, and full body suits are examples of personal protection equipment.
Healthcare Facilities Using PPE:
Gloves safeguard the hands; gowns or aprons defend the skin or clothing; masks and respirators screen the mouth and nose; goggles guard the eyes; and face shields cover the complete face.
To learn more about personal protection equipment refer to:
https://brainly.com/question/13720623
#SPJ1
what is meant by the term "high efficiency purge unit
Those purge units which discharge a high percentage of refrigerant with the air which they remove.
what is meant by the term "high efficiency purge unit?The refrigerant may leave the system together with air and moisture while the purge unit is running. The amount of refrigerant removed along with the air by a high-efficiency purge unit is negligible. On the other hand, an ineffective purge unit will continue to leak a significant volume of refrigerant.
The high efficiency purge unit is made up of a self-contained control system, a refrigerant-cooled condenser tank, a magnetic drive oil pump with three-way suction and discharge valves, connecting tubing, strainers, and driers.
The primary goal of the purge system is to keep the refrigeration system free of moisture and non-condensable gases (air). An rise in condensing pressure brought on by the buildup of non-condensable gases within the system lowers operating efficiency.
To learn more about purge unit refer to:
https://brainly.com/question/17438851
#SPJ4
Shanika is an engineer at an amusement park who is experimenting with changes to the setup for a magnetic roller coaster ride. In one ride, there are two identical roller coaster cars (orange and green) that start on opposite sides of a large magnet located at the center of a station. Shanika wants to get the largest increase in potential energy she can by moving one car one space to the left or the right.
Shanika needs to move the orange coaster car to point B. This movement will result in the greatest potential energy increase.
What is potential energy?Potential energy is stored energy that is influenced by the relative position of various system components. The potential energy of a spring increases when it is compressed or stretched. When a steel ball is raised above ground, it has more potential energy than when it falls to Earth.
In the elevated position, it can do more work. Potential energy is a property of a system, not an individual body or particle; for example, as the Earth and raised ball are separated, the system has more potential energy.
Potential energy exists in systems with parts that exert varying magnitudes of forces on each other based on their configuration, or relative position.
Learn more about Potential energy
https://brainly.com/question/24284560
#SPJ4
in a typical client-server database application, the client is called the ____.
Typically, the client is referred to as the front-end in client-server database applications.
What is a "database"?
An organized group of data that is electronically accessible and stored is referred to as a database in computing. Large databases are housed on computer clusters or cloud storage whereas small databases can be kept on a file system. Database design involves both formal methods and pragmatic factors, such as representing data, effective data representation and storage, query languages, privacy and security of sensitive data, as well as distributed computing problems, such as continuing to support concurrent access and fault tolerance.
To know more about database
https://brainly.com/question/29412324
#SPJ4
Calculate the backwash velocity necessary to expand a sand filter with an effective size of 0.6 mm and a uniformity coefficient of 1.3. This medium (or any other, for that matter) can be cleaned at a backwash velocity of 0.3 m/min if the fluidization is provided by air scour. Calculate the volume of water saved during a 10 min backwash of a 2 by 4 m filter if air scours is used. If the cost of water production is 25 BDT/m3, how much money would be saved per year by air fluidization if the filter runs on average 2 days in length?
The backwash velocity necessary to expand a sand filter with an effective size of 0.6 mm and a uniformity coefficient of 1.3 is 15.6 mm/min or 0.156 m/min
The volume of water saved during a 10 min backwash of a 2 by 4 m filter if air scours is used is 4560 L
The money that would be saved per year by air fluidization if the filter runs on average 2 days in length is 8.1*10^5 BDT/year.
How can you calculate the backwash velocity, volume of water and money to be saved?To calculate the backwash velocity necessary to expand a sand filter with an effective size of 0.6 mm and a uniformity coefficient of 1.3, the following formula can be used:
Backwash velocity = (effective size * uniformity coefficient) / 3
Plugging in the values, we get:
Backwash velocity = (0.6 mm * 1.3) / 3 = 0.26 mm/s
To convert this to meters per minute, we multiply by 60:
Backwash velocity = 0.26 mm/s * 60 = 15.6 mm/min or 0.156 m/min
The fluidization is provided by air scour, which can clean the medium at a backwash velocity of 0.3 m/min.
To calculate the volume of water saved during a 10 min backwash of a 2 by 4 m filter if air scours is used, we can use the formula:
Volume of water saved = (filter area * backwash time * water flow rate) - (filter area * backwash time * air flow rate)
Plugging in the values, we get:
Volume of water saved = (2 m * 4 m * 600 L/min) - (2 m * 4 m * 0.3 m/min) = 4800 L - 240 L = 4560 L
If the cost of water production is 25 BDT/m3, the money saved per year by air fluidization if the filter runs on average 2 days in length can be calculated as:
Money saved per year = (volume of water saved per backwash * number of backwashes per year) * (cost of water production)
Plugging in the values, we get:
Money saved per year = (4560 L/backwash * 365 / 2 days/year) * 25 BDT/m3 = 8.1*10^5 BDT/year
Therefore, the correct answers are as given above
learn more about velocity: https://brainly.com/question/80295
#SPJ1
The attributes of Accounts relation are:
• acctNo
• type
• balance
The attributes of Customers relation are:
• firstName
• lastName
• idNo
• account
The criteria are enumerated, but the most crucial ones are consistency, comparability, reliability, and relevance. Additionally, each of them has a purpose that will have an impact on the accounting data.
Account Attributes are detailed information linked to a record. Each attribute screen offers basic descriptive information about an account, such as the account title, the name of the person who is in charge of it, its function, and the division of the company that uses it. Accounting comprises summarizing, interpreting, and conveying the financial data to the consumers of financial statements in addition to bookkeeping. The primary goal is to keep meticulous records of financial activities. The primary goal is to evaluate the company's financial health and profitability.
Learn more about function here-
https://brainly.com/question/17216645
#SPJ4
Which of the following commands can be used to check if TCP port 80 is open on the remote host 10.0.0.3? O ping O dig O nslookup O telnet
Telnet can be used to check if TCP port 80 is open on the remote host 10.0.0.3 by running the command "telnet 10.0.0.3 80" in the command prompt. If the port is open, you will see a blank screen and be able to type, otherwise you will see a message indicating that the connection could not be established.
What is Telnet?
Telnet is a network protocol that allows users to connect to a remote host and run commands on that host as if they were logged in locally.
Telnet uses a virtual terminal connection to enable communication between the two systems, allowing users to log in to a remote host and run commands, as well as to transfer files.
Telnet is an unencrypted protocol and data is sent in plaintext, which makes it vulnerable to eavesdropping and man-in-the-middle attacks, for this reason it's not recommended to use telnet anymore and replaced with SSH(Secure Shell)
To know more about Telnet, visit: https://brainly.com/question/15060691
#SPJ4
Which is the most common way to install memory in a laptop
Find the cover for the memory module slot. Insert the module by sliding it. The majority of socket alignments are roughly 30 degrees. Change the memory.
What exactly is memory?Memory is the ability to take in information from the surrounding environment, process it, store it, and then recall it at a later time—sometimes years later. A memory storage system or filing cabinet are frequently used as analogies for human memory.
Why is memory so crucial?Memory is a necessary part of every person's life. We are unable to function with in present or consider the future without a remembrance of the past. We wouldn't be able to recall our actions from the previous day, the present, or the future.
To know more about memory visit:
https://brainly.com/question/11103360
#SPJ1
Which part should be tested?
O Flame sensor
O Expansion valve
O Solenoid valve
O Gas valve
Part of the gas valve should be examined. Since they are utilised in various situations, there are several types of gas valves.
Oil and gas flow may be controlled with the use of a gas valve. The volume of liquids and gases permitted to pass through pipes is controlled by opening or shutting an aperture. The valve regulates fluid flow by stopping and beginning, altering quantities, controlling direction, regulating pressure, or releasing pressure.
Environments vary from one another. A few are extremely caustic. While some people work under continual intense pressure. Variations of valves have been created over the years due to these variations. There are benefits and drawbacks to each type of valve. Knowing the various types and purposes within the gas and oil business is necessary for successful operation and application.
Learn more about Gas valve here:
https://brainly.com/question/29426485
#SPJ4
No underwater luminaires shall be installed in a permanently-installed swimming pool that operates on supply circuits over ____________ between conductors.
No underwater luminaires shall be installed in a permanently-installed swimming pool that operates on supply circuits over 50 volts between conductors.
What is underwater luminaires?
Underwater luminaires are lights that are designed to be used underwater, typically in swimming pools or other bodies of water.
They are used to provide illumination in and around the water, and can be used for a variety of purposes such as safety, aesthetics, or recreation. They are typically waterproof and sealed to prevent water from entering and damaging the electrical components.
What is conductor?
A conductor is the material which allows electricity to continuosly flow through it easily. In the context of an electrical circuit, a conductor is a material, typically a metal such as copper or aluminum, that allows an electric current to flow through it, thus connecting different parts of an electrical circuit.
Conductors are used to make wires and other components that are used to transmit electricity in a variety of devices and systems, including power grids, electronic devices, and lighting systems.
To learn more about Conductor, visit: https://brainly.com/question/29304605
#SPJ4
A new split system should be checked for leaks by;
A new split system should be checked for leaks by; pressurizing the system with a few ounces of system refrigerant and an inert gas.
What is a split system?A split system is one of the most widely used house air conditioning configurations today. It consists of two units, one inside and one outside. These systems are renowned for being silent and energy-efficient, and they are quite simple to instal as no ducting is needed.
The compressor, propeller fan, circuit board, and heat exchange coil are all located in this area of the air conditioning system. It is outside and moves refrigerant to and from the indoor unit it is paired with.
This component is frequently referred to as a "condenser" or "heat exchanger." the component of an air conditioning system that is housed and delivers the room's "conditioned" air. A heat exchange coil, filters, and a remote signal receiver are included in this unit.
To learn more about split system refer to:
https://brainly.com/question/20597527
#SPJ4
Sharon drives her rocket through a magnetic field, traveling to the right at a speed of 1000 m/s as measured by Bill. As she passes Bill, she shoots a positive charge backward at a speed of 1000 m/s relative to her ? A.) according, to Sharon, what kind of force or forces Act on the charge? In which directions? Draw the forces on the charge. B) according to Bill, what kind of force acts on the charge? In which directions? Draw the forces on the charge. Explain the physics of what causes that force.
The positive charge will experience two forces acting on it: a magnetic force in the opposite direction its motion, & an electric force in same direction as motion.
What is Lorentz force?The Lorentz force is the force that a moving charge experiences in an electromagnetic field. It is the combination of electric and magnetic force, and is the result of the interaction between a moving charged particle and an electromagnetic field. The Lorentz force is given by the equation: F = qE + qv × B, where q is the charge of the particle, E is the electric field, v is the velocity of the particle, and B is the magnetic field.
To know more about Lorentz force visit :
https://brainly.com/question/29944190
#SPJ4
The device shown is used to mix soils in order to provide in-situ stabilization. If the mixer is connected to an A-36 steel tubular shaft that has an inner diameter of 3 in. and an outer diameter of 4.5 in., determine the angle of twist of the shaft at A relative to C if each mixing blade is subjected to the torques shown.
Angle of shaft twist at A with respect to C is equal to (2.12*107) * (/180) = 37,819°.
Regarding soilThe mixture of organic matter, minerals, gases, liquids, and living things that makes up soil—also referred to as earth or dirt—supports life. Some scientific interpretations differentiate between soil and dirt by limiting the former term to only displaced soil. In addition to a highly permeable phase that holds water and gases (the soil environment), soil includes a solid phase made up of minerals and organic matter (the soil composite) (the soil solution). The three states of soil - solids, liquids, and gases. Climate, relief (elevation, direction, and slope of the terrain), organisms, and the soil's parent materials (initial minerals) all play a role in the formation of soil.
To know more about soil visit :
https://brainly.com/question/1218235
#SPJ4
What is the basic law concerning transformers?
The basic law concerning transformers is the law of conservation of energy, which states that energy can neither be created nor destroyed, only transformed from one form to another.
What is transformers?
Transformers are electronic devices that are used to change the voltage, current, or frequency of alternating current (AC) electricity. They are important components in electrical power systems, allowing power to be transmitted over long distances and between different voltage levels. Transformers consist of two coils of wire, known as the primary and secondary windings, with an iron core in the middle that serves to link the two coils together. When an alternating current is applied to the primary winding, it creates an alternating magnetic field, which in turn induces a voltage in the secondary winding.
To learn more about transformers
https://brainly.com/question/29665451
#SPJ4
a rotor has been refinished an off-car brake lathe. you should do all of the following except: group of answer choices make sure it has a non-directional finish measure the final thickness wipe it down with oil to prevent it from rusting. wash it with soap and water
A rotor has been refinished on an off-car brake lathe. you should do all of the following except Make sure it has a non-directional finish.
A rotor is a rotating component of a machine, such as an electric motor or a turbine. It is typically made of a metal or composite material and is designed to spin at high speeds. Rotors are used in a variety of applications, such as in electric motors, turbines, and pumps. In electric motors, the rotor is the part that rotates and is connected to the stator, which is the stationary part of the motor. The rotor is typically made up of a series of magnets or coils that interact with the stator to generate a magnetic field. This magnetic field is used to generate torque, which is then used to rotate the rotor. In turbines, the rotor is the part that rotates and is connected to the blades, which are used to convert the energy of the moving fluid into mechanical energy. In pumps, the rotor is the part that rotates and is connected to the impeller, which is used to move fluid. Rotors are also used in measuring devices, such as laser rangefinders, to measure distances.
Learn more about rotor here
https://brainly.com/question/29991125
#SPJ4
Required information A flat quadrilateral plate finite element is shown. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. node 4 node 3 node 1 (20, 20, 12) cm node 2 (25, 40, 7) cm node 3 (0,35, 13) cm node 4 (5, 20, 15) cm r node 1 node 2 Determine the unit vector outward normal direction to the surface (i.e., pointing away from the origin). The unit vector is û = O The unit vector is i O i Oł ).
The surface's unit vector's outward normal direction (i.e., pointing away from the origin). û = O is the unit vector. It is I O I O for the unit vector. is u equal to 0.1924i, 0.1924j, and 0.9622k
20, 22, 12 cm for Node 1.
25,40.7 cm for Node 2.
0.35.1 cm for Node 3
5,20,15 cm for node 4.
Each side's cartesian shape
a = 5i + 20j - 5k
b = -15i + 0j + 3k
c = 5i - 15j + 2k
d = 25i +5j - 6k
The surface's unit vector's outward normal direction is:
c*d/I c*d = u I\s= 80i+80j+400k/415.69
u = 0.1924i + 0.1924j + 0.9622k
A quantity or phenomena with independent directions and magnitudes is called a vector. The phrase also describes how such a quantity is represented mathematically or geometrically.
In nature, vectors may be found in electromagnetic fields, weight, momentum, force, and velocity. The force created when gravity accelerates a mass is known as weight.
Learn more about Vector here:
https://brainly.com/question/21157328
#SPJ4
Given: A homogeneous quarter-circle block (with a radius of
R
and a weight of
W
) is supported by a rough, horizontal floor, as shown.. A force
P
is applied to the block at corner
B
. Find: For this problem: a) Determine the
x
-location of the normal force acting on the block by the floor. Express your answer in terms of
R
. b) What is the minimum coefficient of static friction between the block and ground,
μ
s
, that is required to prevent motion of the block? c) Is the block in a state of impending slipping or tipping for the value of
μ
s
found in b) above? Explain. For this problem, use:
P=W
When a circle is divided into four equal parts, each part is called the quarter of a circle.
What is meant by quarter circle?A circle is a geometric shape that represents the path all of those points take while being equally distance from the circle's centre. A circle's quarter represents one-fourth of the entire circle. As a result, the area of a quarter circle represents the fourth of a circle's total area.
The area of the circle, A = r2 if the radius of the circle is r, follows.
The area of a quarter circle is then equal to A times 14 to get r2/4.
Therefore, the coordinates of a quarter ring's centre of mass in the first quadrant are (XCM,YCM)=(2R,2R). Note: Always consider a small mass when determining the centre of mass.
To learn more about quarter of a circle refer to:
https://brainly.com/question/915567
#SPJ1
Calculate v and ix in the circuit of Fig. 2.79.
The expression for the voltage across the resistor is v=6V and I^ x=-4A
Step by step explanation:
The current in the loops are, I^ 1 in loop 1 and I^2 in loop 2
Apply Kirchhoff's voltage law to loop 1.
10=12i^ 1 +4
10-4=12i^ 1
12i^ 1=6
I^ 1 = 6/12=0.5 A
Write the expression for the voltage across the resistor:
V=12I^ 1
=12(0.5)
v=6V
Apply KVL in loop 2:
3i^ x+16=4
3i^ x=-12
I^ x=-12/3
I^ x=-4A
Kirchhoff's Voltage Law describes the distribution of electrical voltage within an electrical circuit's loop, or closed conducting path. According to Kirchhoff's Voltage Law.
Any loop's algebraic sum of voltage (potential) differences must equal zero.
To learn more about Kirchhoff's Voltage Law:
https://brainly.com/question/29831050
#SPJ4
An arbitrary temperature scale
Boiling water temperature __
Room temperature __
Ice water temperature__
Boiling nitrogen temperature __
Absolute zero__
Answer:
he j get too much to do and l don't know to check to yiThe cantilevered rectangular bar is subjected to the force of 5 kip. Determine the principal stress at point A and B
To determine the principal stress at point A and B on a cantilevered rectangular bar subjected to a force of 5 kip, a detailed analysis of the structure would need to be performed.
Principal Stress Calculation-Rectangular BarInvolve determining the distribution of stresses throughout the bar due to the applied load, and then determining the maximum and minimum principal stresses at points A and B.
Assuming a rectangular cross section, The principal stresses can be calculated by Mohr's Circle. The equations for principal stresses are:
σ1 = (σx + σy + √((σx - σy)² + 4τxy²))/2
σ2 = (σx + σy -√((σx - σy)² + 4τxy²))/2
Where, σx and σy are the normal stresses, and τxy is the shear stress.
It is important to note that the analysis would also require information about the material properties, cross-sectional dimensions, and boundary conditions of the bar, as well as a detailed understanding of the loading conditions and any other factors that may affect the distribution of stresses in the structure.
Learn more about Principal Stress here:
https://brainly.com/question/21139723
#SPJ4
What is the esr in the capacitor.
The esr in the capacitor refers to the value that represent the loss of useful energy in a simple electronic circuit consisting of a resistor
What is esr?Equivalent series resistance (ESR), also referred to as internal resistance, is a measurement of the energy lost in a simple electronic circuit made up of a resistor and a perfect (ideal) capacitor. Technically, the energy is not lost; instead, it typically dissipates as unwanted heat.
High frequency noise crosses the capacitor more frequently at the input as the ESR rises, reducing the efficiency of the filter. Higher ESR at the output results in more ripple, which affects the stability of the control loop. ESR is crucial in applications that use high-frequency, low-duty-cycle current pulses.
Learn more about capacitor on:
https://brainly.com/question/27393410
#SPJ1
Calculate I_o In The Circuit Of Fig. 2.91
v=2v and I^ 0=1 A
Explanation:
Apply KCL at node(1)
=V-10/8+V/3+V/6=0
=3v-30+8v+4v/24=0
=15v=30
v=30/15
v=2v.
Therefore:
I^ 0=10-v/8
I^ 0=10-2/8
I^ 0=1 A
A node in a circuit is previously defined as a point where two or more circuit elements are connected together. Kirchoff’s current law (abbreviated "KCL") states that the sum of all currents entering and exiting a node must equal the sum of all currents entering and exiting the node.
In other words, the net current entering (or leaving) any circuit node must be zero. This law is essentially a statement of charge conservation: if the net current entering any node is greater than zero, there will be a net buildup of charge at a point in a circuit over time.
To learn more about ''Kirchoff’s'' current law (KCL)
https://brainly.com/question/16155576
#SPJ4
The repair order must detail why the vehicle is in for repairs or what the customer is complaining about. What’s this known as on the repair order?
The repair order must detail why the vehicle is in for repairs or what the customer is complaining about. Note that this on the repair order is known as Problem Description.
What is the use of a Repair Order?A repair order is a document used in an automotive repair shop or service center to document the details of a repair job.
It contains information about the vehicle, the customer, the problem or reason for the repair, the work done, and the repair cost. It is used as a record of the work done and for billing and warranty purposes.
Learn more about repair orders:
https://brainly.com/question/7199470
#SPJ1