The final enrichment would be 97.5%, which is the amount of U235 in the total fuel, divided by the total weight of the fuel.
What is the amount of natural uranium must be used?Uranium from one bomb = 1 tons = 1000 kg. Uranium required for one reactor = 40,000 kg Percent enrichment of U-235 in uranium used for bomb = 100%.
Enrichment = (% of U-235 / % of U-238) +1
Natural Uranium contains 0.711% of U-235.
Calculations: As we know that Uranium from one bomb = 1 tonne = 1000 kg.
To obtain a total of 40,000 kg of fuel needed by one reactor for startup, we need to mix 40 bombs. Let's find out the total mass of U-235 present in 40 bombs:
Total mass of U-235 = 1000 × 40 = 40,000 kg.
Enrichment = (% of U-235 / % of U-238) +1
Let the percentage of U-238 = X
Enrichment = (100/ X) + 1
We know that Natural Uranium contains 0.711% of U-235, So the percentage of U-238 in natural uranium will be 99.289%
Let X = 99.289%
Enrichment = (100/ 99.289%) + 1
Enrichment = 1.007%
Thus, the mass of natural uranium used = 40,000/0.007 = 5,71,42,857.14 kg (approx)
Final enrichment = 1.007%
To learn more about the uranium :
https://brainly.com/question/179933
#SPJ11
Given the definition of EER, find the EER of an 8000 Btu/hour air conditioner that requires a power input of 1500 W. Express your answer numerically in British thermal units per hour per watt. EER = __________(Btu/hour)/W
EER is defined as the Energy Efficiency Ratio which is the ratio of cooling capacity in BTU/hr to the power input in watts.
The EER of the given 8000 Btu/h air conditioner is 5.33 Btu/hour per watt.
In the case of the given 8000 Btu/h air conditioner that requires a power input of 1500 W, the EER can be calculated as follows:
EER = (cooling capacity in Btu/hr) / (power input in watts)
EER = 8000 Btu/hour / 1500 W = 5.33 Btu/hour per wat.
Energy efficiency ratio (EER) is used in the USA and is defined as the system output in Btu/h per watt of electrical energy.
Coefficient of performance (COP) is the equivalent measure using SI units, which is widely used in the UK. A COP of 1.0 equates to an EER of 3.4.
To know more about power:https://brainly.com/question/11569624
#SPJ11
a piano tuner uses a tuning fork to adjust a piano wire to certain frequency. how does the piano tuner do this (select all that apply)?
Adjust the tension in the piano wire using a tuning wrench until the beats or interference disappear, indicating that the frequencies are now the same.
What is Frequency?
Frequency is the number of cycles of a periodic wave that occur in a given unit of time. The higher the frequency, the more cycles occur per unit of time, and the higher the pitch of the sound wave associated with the frequency. In general, frequency is used to describe any regularly recurring event or pattern, such as the oscillation of a pendulum, the vibration of a guitar string, or the electromagnetic waves that make up light and radio signals.
The piano tuner uses the following methods to adjust a piano wire to a certain frequency:
Strike the tuning fork to create a pure tone with a known frequency.
Hold the tuning fork close to the piano wire and listen for any beats or interference between the two frequencies.
Verify the tuning using a piano tuning app or a reference tone, if necessary.
Learn more about Frequency from given link
https://brainly.com/question/254161
#SPJ1
1 80 kg scaffold is 5.80 m long. it is hanging with two wires, one from each end. a 580 kg box sits 1 m from the left end. what is the tension in the right hand side wire?
The tension in the right-hand side wire is 6525 N.
Given:
Weight of the scaffold = 180 kgLength of the scaffold = 5.8 mWeight of the box = 580 kgDistance of the box from left end = 1 mLet the tension in the left wire = T1Let the tension in the right wire = T2To find: Tension in the right-hand side wireWe know that the sum of forces acting in a vertical direction should be equal to 0 as there is no acceleration in the vertical direction. ∑Fv = 0In the horizontal direction, there are no forces acting on the system.
∑Fh = 0Now considering forces in the vertical direction: T1 + T2 = (Weight of scaffold + Weight of the box) gT1 + T2 = (180 + 580) x 9.8T1 + T2 = 7644 N1. From the diagram, we can see that the box is nearer to the left side. Hence, the tension force in the left wire is greater than the tension force in the right wire.
T1 > T22. Let's take moments about the right end of the scaffold as shown in the figure below.
∑Mr = 0T1 × 5.8 = T2 × 1T2 = 5.8/1 × T1T2 = 5.8T1Now, we can substitute the value of T2 in equation (1):
T1 + T2 = 7644N6.8 T1 = 7644 N T1 = 1125 NTo find T2, we can substitute the value of T1 in equation (2):
T2 = 5.8 × T1T2 = 5.8 × 1125 N T2 = 6525 NTherefore, the tension in the right-hand side wire is 6525 N.
Learn more tension: https://brainly.com/question/4001686
#SPJ11
on a sunny day, a rooftop solar panel delivers 55 w of power to the house at an emf of 17 v . part a how much current flows through the panel? express your answer with the appropriate units.
On a sunny day, a rooftop solar panel delivers 55 w of power to the house at an emf of 17 v . the current flows through the panel is 3.235 A.
The amount of current flowing through the panel can be calculated using Ohm's Law (I = p/v). When working with the formula, Power = Voltage × Current (P = V × I), one can determine the current that flows through the panel by rearranging the formula to:
Current = Power/Voltage (I = P/V).
The calculation of the current (I) is given as follows: I = P/V = 55 W / 17 V = 3.235 A.
Therefore, 3.235 A of current flows through the solar panel on a sunny day.
Read more about current here:
https://brainly.com/question/12785175
#SPJ11
consider an experimental setup where charged particles (electrons or protons) are first accelerated by an electric field and then injected into a region of constant magnetic field with a field strength of 0.55 t.
What is the potential difference in volts required in the first part of the experiment to accelerate electrons to a speed of 6 1 × 107 m/s?
The potential difference in volts required in the first part of the experiment to accelerate electrons to a speed of 6.1 × 107 m/s is 73 kV.
What is potential difference?Potential difference is the amount of energy that is required to move a unit charge through an electric field from one point to another. The unit of potential difference is volts (V), and it is a scalar quantity. It is also known as voltage or electric potential difference.
The formula for calculating potential difference is as follows: Potential difference (V) = work done (J) / charge (C) or
V = W / Q,
where W is the work done and Q is the charge involved in the process
Work done is given as: W = F × d × cosθ
where, F is the force, d is the displacement, and θ is the angle between the force and the displacement.
Therefore, V = (F × d × cosθ) / Q
Field strength = 0.55 T
Charge on the electron, -e = 1.6 × 10¹⁹ C
Mass of the electron, me = 9.1 × 10⁻³¹ kg
Speed of the electron = 6.1 × 10⁷ m/s
The electric field (E) is given as: E = V / d
F = Q × E = -e × V/d = -1.6 × 10⁻¹⁹ × V / 0.5 = -3.2 x 10⁻¹⁹ × V N
θ = 0° (as the force and displacement are parallel)
W = F × d × cosθ = F × d = -3.2 × 10⁻¹⁹ × V × 0.5 = -1.6 × 10⁻¹⁹ × V J
Now, the kinetic energy (KE) of the electron is given as: KE = 1/2 mv²
Substituting the values, we get: KE = 1/2 mev² = 1/2 × 9.1 × 10⁻³¹ × (6.1 × 10⁷)² = 2.8 × 10⁻¹⁷ J
As the work done by the electric field is equal to the kinetic energy of the electron, we can equate the values:
1.6 × 10⁻¹⁹ × V = 2.8 × 10⁻¹⁷
Solving for V, we get: V = -2.8 × 10⁻¹⁷ / -1.6 × 10⁻¹⁹
V = 175 V
Therefore, the potential difference in volts required in the first part of the experiment to accelerate electrons to a speed of 6.1 × 10⁷ m/s is 175 V.
Learn more about Potential difference here:
https://brainly.com/question/12198573
#SPJ11
Which turbine takes the lesser amount of time to rotate through 1.0 radian of angular displacement? a. turbine A b. turbine B c. They take the same amount of time. d. The answer cannot be determined from the information given.
The correct option is C, The turbine that takes the lesser amount of time to rotate through 1.0 radian of angular displacement is both because They take the same amount of time.
A turbine is a device that converts kinetic energy from a fluid (such as water, steam, or air) into mechanical energy. It is composed of a series of rotating blades that are attached to a shaft. When the fluid flows over the blades, it causes them to rotate, which in turn rotates the shaft.
Turbines are commonly used in power generation to generate electricity. For example, in a hydroelectric power plant, water flows through a turbine, which spins a generator to produce electricity. Similarly, in a gas or steam turbine power plant, the combustion of fuel heats up air or water to create steam, which flows through a turbine to produce electricity.
To learn more about Turbine visit here:
brainly.com/question/30559123
#SPJ4
You are the process engineer at Corvallis Automobiles Inc., and you have received an order to turn a cylindrical bar on an engine lathe to the dimensions specified in Fig. 1. For this order you will use cylindrical bar stock that is 48-inches long and 4-inches in diameter. The 48-inch length bar will be chucked in the lathe and supported at the opposite end using a live center. You are planning to complete the operation in one pass using a cutting speed of 400 ft./min. and a feed of 0.010 in./rev. Determine the following: a) The required depth of cut (in inches) b) The material removal rate (in cubic inches per minute)
c) The time required to complete the cutting pass (in minutes)
a. the depth of cut is 0.625 inches.
b. the material removal rate is 0.003125 cubic inches per minute.
c. the time required to complete the cutting pass is 20 minutes.
How do we calculate?a) The required depth of cut can be determined by :
DOC = (4 in - 2.75 in)/2 = 0.625 in
Therefore, the depth of cut is 0.625 inches.
b) The material removal rate can be found by applying:
MRR = DOC x Width of cut x Feed rate
assuming we are using a standard carbide insert tool with a width of cut of 0.5 inches.
MRR = 0.625 in x 0.5 in x 0.010 in/rev = 0.003125 cubic inches per minute
c) The time required to complete the cutting pass is determined by:
Time = Length of cut / (Cutting speed x Width of cut x Feed rate)
Time = 48 in / (400 ft/min x (0.5 in) x (0.010 in/rev) x (1/12 ft/in)) = 20 minutes
Learn more about material removal rate at: https://brainly.com/question/13106351
#SPJ1
The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1.2-mm-diameter sphere. The properties of the junction are k = 35 W/m °C, rho= 8500 kg/m3 ,and Cp = 320 J/kg °C, and the heat transfer coefficient between the junction and the gas is h = 65 W/m2 °C. Determine how long it will take for the thermocouple to read %95 of the initial temperature difference.
It will take about 12.12 minutes for the thermocouple to read 95% of the initial temperature difference of the sphere. This is due to difference in temperature.
What is the time required to read 95% of initial temperature difference?
In order to determine how long it will take for the thermocouple to read 95% of the initial temperature difference, the following formula is used:
t = (rho × V × Cp)/(h × pi × D) × ln ((Tinitial - T∞) / (Tinitial - Tcutoff))
where, t = time (s), ρ = density (kg/m³), V = volume (m³), Cp = specific heat capacity (J/kg °C), h = heat transfer coefficient (W/m²°C), D = diameter (m), Tinitial = initial temperature (°C), T∞ = surrounding temperature (°C), Tcutoff = temperature at which the thermocouple reading is 95% of the initial temperature difference (°C).
Substituting the given values into the above formula:
t = (8500 kg/m³ × (4/3 × pi × (0.0006 m)³)) / (65 W/m2 °C × pi × 0.0012 m) × ln ((100 °C - 25 °C) / (100 °C - 95 °C))
t = 727.31 s or 12.12 minutes.
Therefore, it will take approximately 12.12 minutes for the thermocouple to read 95% of the initial temperature difference.
Learn more about Thermocouple here:
https://brainly.com/question/14555057
#SPJ11
calculate the magnitude of the gravitational field of the sun at the location of earth, in meters per square second.
The magnitude of the gravitational field of the Sun at the location of Earth is approximately 9.81 m/s2.
This value is derived from Newton's Law of Universal Gravitation, which states that the gravitational force (F) between two objects is equal to the product of the two objects' masses (m1 and m2) multiplied by the gravitational constant (G) divided by the square of the distance between the two objects (r2):
F = G * m1 * m2 / r2
The mass of the Sun is 1.989 × 1030 kg, and the average distance between Earth and the Sun is 1.496 × 1011 meters. Therefore, plugging those values into the equation gives us:
F = 6.67 × 10-11 * 1.989 × 1030 * 5.972 × 1024 / (1.496 × 1011)2
F = 9.81 m/s2
Read more about the topic of gravitation:
https://brainly.com/question/72250
#SPJ11
Give a counterexample to show that the following construction fails to prove that the class of context-free languages is closed under the star operation. Let A be a CFL that is generated by the CFG G = (V, σ, R, S). Add the new rule S → SS and call the resulting grammar G0 . It is hoped that G0 generates A∗ .
Consider the following counterexample to prove that the construction fails to prove that the class of context-free languages is closed under the star operation:
Let A be a context-free language that consists of only one word "a".
So, the grammar for A would be as follows: G = ({S}, {a}, {S → a}, S)
Let A* be the concatenation of any number of words of A including 0 words.
Hence, A* = {ε, a, aa, aaa, aaaa, …}
Now, construct G0 by adding the new rule S → SS to G.
So, the grammar G0 would be as follows: G0 = ({S}, {a}, {S → a, S → SS}, S)
According to the construction, we can say that G0 generates A* if A is a context-free language.
However, A* can be shown as not context-free using pumping lemma for context-free languages.
Hence, we can say that G0 does not generate A* although A is a context-free language. Thus, the construction fails to prove that the class of context-free languages is closed under the star operation.
To know more about "context-free language" refer here:
https://brainly.com/question/29762238#
#SPJ11
Which of these stars has the greatest surface temperature? a.... Which of these stars has the greatest surface temperature? a. a main-sequence B star b. a supergiant A star c. a giant K star
A main-sequence B star has the greatest surface temperature among the given options. B-type stars are hotter and more massive than A-type stars, which are in turn hotter and more massive than K-type stars.
The star with the highest surface temperature among these three classifications is a main-sequence B star. A, F, G, K, and M stars, which make up the majority of main-sequence stars in the Milky Way galaxy, are hotter and less massive than B-type stars. B stars' surface temperatures typically vary from 10,000 to 30,000 Kelvin (K), with some of the hotter stars exceeding 30,000 K. Surface temperatures of K-type giants range from around 3,500 to 5,000 K, whereas those of A-type supergiants range from about 7,500 to 11,000 K.
Learn more about surface temperature here:
https://brainly.com/question/5344945
#SPJ4
which of the following is true regarding adipocere? 1. also known as grave wax. 2. created by a hydrolysis reaction. 3. is chemically similar to a soap. 4. is created from a carbohydrate.
Adipocere, also referred to as corpse wax, grave wax, or mortuary wax is an organic substance with a wax-like texture that results from the hydrolysis of fat in tissues, including body fat in deceased bodies, by anaerobic bacteria.
Option 1 is true: Adipocere is also known as grave wax.
Option 2 is partially true: Adipocere is formed by a chemical reaction called saponification, which is the breakdown of fats in adipose tissue by the hydrolysis action of enzymes or bacteria.
Option 3 is true: Adipocere is chemically similar to soap because it is a type of fatty acid salt, specifically a calcium or magnesium salt of fatty acids.
Option 4 is false: Adipocere is not created from a carbohydrate, but rather from the breakdown of fat in the body.
Learn more about saponification:
https://brainly.com/question/14018257
#SPJ11
what did oersted discover about electricity and magnetism
Hans Christian Oersted established the connection between electricity and magnetism in 1820. The magnetic field produced by the current revolves around the wire in a circle.
Oersted demonstrated how a magnetic field may be produced by moving electrons by establishing a compass through a wire carrying an electric current.
Scientists believed that electricity and magnetism had no connection until the discovery of electromagnetism. Hans Christian Oersted, a scientist from Denmark, revolutionised all of that. He found that an electric current in a wire may cause a magnetic field, as evidenced by the fact that the current can cause a magnetised compass needle to deflect.
The electrons in the wire are pushed when a coil of wire is moved around a magnet or vice versa, producing an electrical current. In essence, kinetic energy—the energy of motion—is transformed into electrical energy via electricity generators.
Learn more about Electricity here:
https://brainly.com/question/12791045
#SPJ4
if stars a and b are both main-sequence stars and star a has a greater fusion rate than star b, which of the following statements hold(s)? check all that apply. A. star a must be more luminous than star b. B. star a must be less luminous than star b. C. star a must be more massive than star b. D. star a must be less massive than star b.
If stars A and B are both main-sequence stars and star A has a greater fusion rate than star B, the following statements hold:
A. Star A must be more luminous than star B.
C. Star A must be more massive than star B.
This is due to the direct relationship between a main-sequence star's brightness and mass and the rate of fusion in that star. A higher fusion rate, therefore, suggests a higher brightness and mass.
StarA star is a large, bright ball of gas that is held together by its own gravity. They create the energy and light that enable life on Earth and serve as the foundation of galaxies.In space, gas and dust clouds collide under the force of their own gravity to generate stars.Nuclear fusion starts when the cloud's center reaches roughly 10 million degrees Celsius as it warms up and falls. This is how hydrogen atoms come together to create helium, unleashing a massive quantity of energy in the form of heat and light.The star can retain a steady size and form because the energy produced by fusion produces an outward pressure that balances the pull of gravity.learn more about luminous here
https://brainly.com/question/25030787
#SPJ1
if a satellite circulate around the earth at a height of 7323.77km above the earth's surface, given the earth radius is 3958.8 miles and mass is 5.98 x 10 kg, use G=6.674 X 10^-11 Nm^2/kg^2. find the perios of this satellite in unit hours? _______
The period of the satellite circulating the earth at the height of 7323.77km above the earth's surface is 2.14 hours.
We know that the radius of the Earth is 3958.8 miles, i.e. 6371 km, the mass of the Earth is 5.98*10²⁴kg and the height of the satellite is 7323.77 km
The formula used to find the period of a satellite is given by:-
[tex]T = 2\pi\sqrt{\frac{r^3}{GM}}[/tex]
Where, T = Period of the satellite, r = Radius of the satellite from the center of the earth, G = Gravitational constant, and M = Mass of the Earth.
We know that the height of the satellite from the surface of the earth is given by:-
[tex]R = r + h[/tex]
Where R = Radius of the earth, h = Height of the satellite from the surface of the earth.
Substituting the given values,
R = 6371 + 7323.77 = 13694.77 km = 8.5 miles
Therefore,
r = 13694.77 km
T = [tex]2\pi \sqrt \frac{r^3}{GM}[/tex]
= [tex]2\pi \sqrt\frac{13694.77^3}{(6.674 * 10^{-11} * 5.98 * 10^{24})}[/tex]
T = 128.85 minutes
Now, convert the time from minutes to hours by dividing by 60:-
Period of the satellite = T = 128.85/60 = 2.14 hours
Learn more about mass: https://brainly.com/question/25959744
#SPJ11
a bicyclist on an old bike (combined mass: 83 kg) is rolling down (no pedaling or breaking) a hill of height 115 m. over the course of the 345 meters of downhill road, she encounters a constant friction force of 239 newton. if her speed at the top of the hill is 9 m/s, what is her speed at the bottom of the hill?
The speed of the bicyclist at the bottom of the hill is 27.5 m/s.
A bicyclist on an old bike with a combined mass of 83 kg is rolling down a hill of height 115 m.
During the course of the 345 meters of downhill road, she encounters a constant friction force of 239 newton.
If her speed at the top of the hill is 9 m/s, what is her speed at the bottom of the hill?The sum of the potential energy and the kinetic energy of the cyclist at the top of the hill will equal the sum of the potential energy and the kinetic energy at the bottom of the hill, as there is no external work done on the cyclist.
Hence, the kinetic energy at the bottom of the hill will be equal to the initial kinetic energy minus the work done due to the frictional force.
The potential energy of the cyclist at the top of the hill = mgh ,where m = 83 kg, g = 9.8 m/s², and h = 115 m
Potential energy = (83 kg) × (9.8 m/s²) × (115 m) = 99749 Joules
At the top of the hill, the total energy of the cyclist is the sum of the potential energy and the kinetic energy.
E_total = 99749 + (1/2) × (83 kg) × (9 m/s)²
E_total = 99749 + 33417.75
E_total = 133166.75 Joules
At the bottom of the hill, the total energy of the cyclist is the sum of the kinetic energy and the work done by friction.
E_total = (1/2) × (83 kg) × v² + (239 N) × (345 m)
E_total = (1/2) × (83 kg) × v² + 82355 Joules
The potential energy of the cyclist has transformed to kinetic energy and work done due to friction.
Equating the two equations above:133166.75 = (1/2) × (83 kg) × v² + 82355Solving for v:249.25 = (1/2) × (83 kg) × v²v² = 5999v = 27.5 m/s
To know more about "constant friction force" refer here:
https://brainly.com/question/30111741#
#SPJ11
Which statement describes what most likely occurs when a magnetic compass is placed next to a simple circuit made from a battery, a light bulb, and a wire?A magnetic field created by the compass causes the light bulb to stop working.A magnetic field created by the electric current causes the compass needle to move.A magnetic field created by the compass increases the current in the electrical circuit.A magnetic field created by the electric current places negative charges on the compass.
A magnetic field created by the electric current causes the compass needle to move. This is the most likely outcome when a magnetic compass is placed adjacent to a basic electrical circuit consisting of a battery, a light bulb, and a wire.
A magnetic field is created around a wire as electricity flows through it. The compass needle moves as a result of the interaction between this magnetic field and the Earth's magnetic field. Consequently, the magnetic field produced by the electric current in the wire causes the compass needle to move when a magnetic compass is put next to a basic circuit comprised of a battery, a light bulb, and a wire. The interplay of magnetic fields and electric currents is employed in numerous applications, such as electric motors and generators, to transform electrical energy into mechanical energy and vice versa.
learn more about magnetic compass here:
https://brainly.com/question/2264542
#SPJ4
which event triggers the creation of an action potential?
The opening of voltage-gated sodium channels triggers the creation of an action potential.
An action potential is a brief electrical signal that travels down the axon of a neuron. This signal is triggered by the opening of voltage-gated sodium channels in response to a stimulus, such as a chemical neurotransmitter binding to a receptor on the neuron's membrane. The influx of positively charged sodium ions depolarizes the membrane, creating an electrical signal that rapidly spreads down the axon. Once the signal reaches the end of the axon, it triggers the release of neurotransmitters, which can then bind to receptors on other neurons and continue the transmission of the signal.
To know more about action potential, here
brainly.com/question/8312195
#SPJ4
The 6-kg collar has a velocity of 2 m/s to the right when it is at A It then travels along the smooth guide shown. The spring has an unscratched length of 100 mm and B is located just before the end of the curved portion of the rod.
The speed of the collar when its center reaches point B is 1.4 m/s.
The velocity of the 6-kg collar when its center reaches point B can be determined using the concepts of velocity, spring length, and conservation of energy.
The equation for conservation of energy is E = 1/2 mv² + 1/2 kx², where m is the mass of the object, v is the velocity, k is the spring constant, and x is the displacement of the spring.
At point A, the initial velocity is 2 m/s and the displacement of the spring is 0, so the total energy is
E = 1/2(6kg)(2m/s)².
At point B, the displacement of the spring is 100mm, so the total energy is
E = 1/2(6kg)(v²) + 1/2k(0.1m)²
Setting these equations equal to each other and solving for v, the velocity of the collar at point B is 1.4 m/s.
Learn more about conservation of energy on:
https://brainly.com/question/166559
#SPJ11
Find the angle ϕ between the filter's polarizing axis and the direction of polarization of light necessary to increase the ratio of the clouds' intensity to that of the blue sky so that it is three times the normal value. Express your answer in degrees to four significant figures
"The required angle Ф between the filter's polarizing axis and the direction of polarization of light necessary to increase the ratio of the clouds' intensity to that of the blue sky so that it is three times the normal value is 65.9°."
A photographer wants to click a picture of a cloud formation, the ratio of clouds intensity to that of the blue sky photographer uses polarizing filter from Malus law,
I = I₀ cos²Ф
So, I f = I i cos²Ф
As the light from cloud is polarized, its intensity reduces to half.
I c = I₀/2
The intensity of light from sky is polarized light.
I s = I₀ cos²Ф
Hence, the ratio of intensities is,
I c/I s = (I₀/2)/(I₀ cos²Ф)
3 = (I₀/2)/(I₀ cos²Ф)
cos²Ф = 1/6
Thus, the required angle is Ф = cos⁻¹(1/√6) = 65.9°
To know more about angles:
https://brainly.com/question/28562350
#SPJ4
I need help with this question
The gardener does 5600 joules of work in pushing the wheelbarrow around the lawn.
Step-by-step calculation:
The distance traveled by the wheelbarrow is the perimeter of the lawn, which is:
Perimeter = 3 m + 4 m + 3 m + 4 m = 14 m
The net force exerted on the wheelbarrow is the sum of the force used to push it along the ground and the force used to lift it off the ground:
Net force = 100 N + 300 N = 400 N
The angle between the force and the direction of motion is 0 degrees, so the cosine of the angle is 1.
The work done by the gardener is given by:
Work = Force x Distance x cos(theta)
Substituting the values we found above, we get:
Work = 400 N x 14 m x cos(0 degrees)
Work = 5600 J
Therefore, the gardener does 5600 joules of work in pushing the wheelbarrow around the lawn.
To know more about perimeter, visit:
https://brainly.com/question/6465134
#SPJ1
consider two planets in space that gravitationally attract each other. if the masses of both planets are doubled, and the distance between them is also doubled, then the force between them is group of answer choices four times as much. half as much. twice as much. remains the same. one quarter.
If the masses of two planets in space that gravitationally attract each other are doubled and the distance between them is also doubled, then the force between them remains the same.
To determine the force between two planets, we use the formula:
F = Gm1m2/r^2
where F is the force of gravitational attraction between the two planets, G is the gravitational constant, m1 and m2 are the masses of the planets, and r is the distance between them.
If both masses are doubled and the distance between them is also doubled, the new force between them can be calculated as follows:
F' = G(2m1)(2m2)/(2r)^2
Simplifying this expression, we get:
F' = Gm1m2/r^2
which is the same as the original force between the planets.
Therefore, if the masses of two planets are doubled and the distance between them is also doubled, the force between them remains the same.
For more similar questions on gravitation and physics:
brainly.com/question/27996005
#SPJ11
when the air is in geostrophic balance, it flows _______ to isobars _________ the boundary layer.
When the air is in geostrophic balance, it flows parallel to isobars and above the boundary layer.
Geostrophic balance is a state of balance between the pressure gradient force and the Coriolis force, where the pressure gradient force is directed from higher to lower pressure, and the Coriolis force is perpendicular to the direction of motion. In this state, the wind flows parallel to the isobars, with the pressure gradient force and the Coriolis force balancing each other out.
The boundary layer is the layer of air near the Earth's surface where friction between the air and the surface slows down the wind and causes it to flow in a more complex manner, with the wind direction changing with height. However, in the geostrophic flow regime, the wind flow is typically above the boundary layer and thus not affected by surface friction.
Therefore, in geostrophic balance, the wind flows parallel to isobars and above the boundary layer, with little to no effect from the Earth's surface.
Learn more about geostrophic balance here
brainly.com/question/28314662
#SPJ4
a roller coaster starts from rest at the top of a hill that is 18 m high. the car travels to the bottom of the hill and continues up the next hill which is 10 m high. how fast is the car moving at the top of the 10.0 m hill if friction is ignored?
The car is moving at a fast speed of 14.4 m/s at the top.
The formula for finding the velocity of the roller coaster is shown below: ½mv2=mgh.
Here,m is the mass of the roller coaster,v is the velocity of the roller coaster,
g is the acceleration due to gravity (9.8 m/s²), andh is the roller coaster's height above the ground.
At the top of the first hill, the roller coaster has a potential energy ofmgh=mg (18) = 18mg
Where,m is the mass of the roller coaster andg is the acceleration due to gravity (9.8 m/s²).
The velocity at the bottom of the first hill can be found using the conservation of mechanical energy:
kinetic energy + potential energy = kinetic energy + potential energy
½mv2 + mgh = ½mv2 + mghv2 = 2gh
At the bottom of the first hill, the kinetic energy is mgh.
The total mechanical energy at the bottom of the hill is thus mgh + mgh = 2mghv
2 = 2gh = 2 × 9.8 × 18v2 = 352.8v = 18.79 m/s
At the top of the second hill, the roller coaster's mechanical energy is once again equal to its potential energy:
potential energy = mgh = mgh = 10mgv = sqrt(2gh) = sqrt(2 × 9.8 × 10) = 14.4 m/s
Therefore, the velocity of the car at the top of the 10.0 m hill is 14.4 m/s.
To learn more about car, click here:
https://brainly.com/question/111325
#SPJ11
standard number of bones in the appendicular skeleton
The standard number of bones in the appendicular skeleton varies slightly among individuals, but it is generally accepted that there are 126 bones in the appendicular skeleton of an adult human.
The appendicular skeleton includes all the bones that are attached to the axial skeleton, which includes the skull, vertebrae, and ribcage. The appendicular skeleton consists of the bones of the arms, legs, pelvis, and shoulder girdle. Here is a breakdown of the number of bones in each part of the appendicular skeleton: Arms: 60 bones (30 in each arm) Legs: 60 bones (30 in each leg) Pelvis: 2 bones Shoulder girdle: 4 bones Adding up these numbers gives a total of 126 bones in the appendicular skeleton. However, this number can vary slightly among individuals due to differences in bone structure and development.
Learn more about bones here:
https://brainly.com/question/29606469
#SPJ4
which of the following includes all common types of radioactive decay? a. atomic number, beta particle emission, electron capture B. alpha particle emission, beta particle emission, half-life C. alpha particle emission, beta particle emission, radioactive parent isotope D. alpha particle emission, beta particle emission, electron capture E. alpha particle emission, stable daughter, electron capture
Alpha particle emission, beta particle emission, and electron capture are all common types of radioactive decay.The correct answer is D.
They are common types of radioactive decay's because:
Alpha particle emission involves the emission of an alpha particle (a helium nucleus) from the nucleus of an atom. This reduces the atomic number by 2 and the mass number by 4.Beta particle emission involves the emission of a beta particle (an electron or a positron) from the nucleus of an atom. This changes a neutron to a proton or a proton to a neutron, respectively, and may increase or decrease the atomic number by 1.Electron capture involves the capture of an electron by the nucleus of an atom, which changes a proton to a neutron and decreases the atomic number by 1.Option D includes all of these types of radioactive decay (alpha particle emission, beta particle emission, and electron capture), so it is the correct answer
To learn more about radioactive decay:
https://brainly.com/question/11117468
#SPJ11
a ford ranger has a mass of 2835 kg is traveling at a velocity of 55 mph down a mountain road in colorado. what distance in feet will it travel if the ramp had a 25% inclinvce
The distance in feet the Ford Ranger will travel can be calculated using the formula is 5,939.66 ft.
Distance (ft) = Velocity (mph) × Time (s) × 0.6818
In this case, Velocity = 55 mph, Time = Unknown.
Using the incline, we can calculate the time it takes the Ford Ranger to travel the given distance:
Time = Distance/[Velocity × (1 + Incline/100)]
Distance = 2835 kg × 9.81 m/s2 × 25% = 7101.75
time = 7101.75/[55 × (1 + 25/100)] = 129.44 seconds
distance (ft) = 55 × 129.44 × 0.6818 = 5,939.66 ft
To find the distance a Ford Ranger with a mass of 2835 kg will travel if the ramp had a 25% incline while traveling at a velocity of 55 mph down a mountain road in Colorado, the following formula will be applied: distance = [velocity² / (2 × acceleration)] × sin(2×angle of incline)
Let's find the acceleration using the formula:
a = (v² - u²) / 2s
where, a = acceleration = final velocity, u = initial velocity = distance
Therefore, a = (55² - 0²) / 2 × s = 166.25 / s... equation [1]
Now, let's find the sine of the angle of incline sin25° = 0.4226
Therefore, the distance the Ford Ranger will travel on a ramp with a 25% incline while traveling at a velocity of 55 mph down a mountain road in Colorado is given by; distance = [55² / (2 × (166.25 / s))] × sin(2 × 25°)
distance = 5,939.66 ft.
Read more about distance here:
https://brainly.com/question/26550516
#SPJ11
a small mirror with area 5 cm^2 faces a monochromatic light source that is 3.2 m away. at the mirror the electric field amplitude of the from the source is 0.028 v/m. how much energy is incident on the mirror in 1 s
The energy incident on the mirror in 1 s is: 5.146 × 10⁻²⁰ J.
Given that, Area of small mirror = 5 cm²
Electric field amplitude of the from the source at the mirror = 0.028 V/m
Distance of monochromatic light source from the mirror = 3.2 m
We need to calculate how much energy is incident on the mirror in 1 s.
Amplitude of a wave is the measure of its strength. It is defined as the displacement of the crest or trough of the wave from its rest position.
In this question, we have the amplitude of the electric field which is 0.028 V/m.
Energy carried by a wave is directly proportional to the square of the amplitude.
The energy of an electromagnetic wave is given by the following relation:
E=hc/wavelength where, h is Planck's constant (6.63 x 10⁻³⁴ J s), c is the speed of light (3 x 10⁸ m/s)
Energy of wave can also be given by the following relation: E=1/2 ε₀ E², where,ε₀ is the permittivity of free space.
Energy of wave can also be given by the following relation:
E=1/2 B₀ H², where, B₀ is the magnetic field constant H is the magnetic field strength
Now, the energy incident on the mirror in 1 s can be calculated as follows:
Electric field amplitude at the mirror = 0.028 V/m
Energy of wave can be given as, E=1/2 ε₀ E²=1/2 × 8.85 × 10⁻¹² C²/Nm² × (0.028 V/m)²= 1.0292 × 10⁻¹⁸ J/m²
Total energy incident on the mirror in 1 s= Energy per unit area × Area of mirror= 1.0292 × 10⁻¹⁸ J/m² × 0.05 m²= 5.146 × 10⁻²⁰ J
To know more about "electric field" refer here:
https://brainly.com/question/8705524#
#SPJ11
phase of the moon where only a very small part of the lit surface is seen from earth is called?
The phase of the moon where only a very small part of the lit surface is seen from the earth is called the crescent moon phase.
This phase occurs when the illuminated portion of the moon is less than half, but not yet a new moon. When the crescent moon appears in the sky, it is usually visible in the west just after sunset and looks like a thin curved shape. The crescent moon is visible for a few days, after which it transitions into the first quarter moon phase. The phases of the moon are a result of the moon's changing position relative to the sun and the earth.
As the moon orbits the earth, different parts of its surface are illuminated by sunlight. This is why we see different phases of the moon as it rotates around the earth. The phases of the moon include the new moon, waxing crescent, first quarter, waxing gibbous, full moon, waning gibbous, third quarter, and waning crescent. The crescent moon phase is just one of these eight phases.
To learn more about Moon :
https://brainly.com/question/13086036
#SPJ11
The major types of stress are ___ A. Ductile and Brittle B. Compression, Ductile, and Brittle C. Compression, Strain, and Deformation D.Shear, Tension and Compression E. Shear, Ductile, Tension, Brittle, and Compression
The major types of stress are shear, Tension, and Compression. Therefore option D is correct.
Stress refers to the internal forces acting on a material, causing it to deform or change shape. Different types of stress can act on a material, and they are characterized by the way in which the forces are applied.
1. Shear stress: Shear stress occurs when two forces act parallel to each other but in opposite directions, causing the material to deform by sliding or shearing.
2. Tension stress: Tension stress occurs when forces are applied to pull a material apart. It leads to elongation or stretching of the material.
3. Compression stress: Compression stress occurs when forces are applied to squeeze or compress a material.
Therefore, the correct answer is D. Shear, Tension, and Compression, as these three options represent distinct types of stress commonly encountered in materials and structures.
Know more about internal forces:
https://brainly.com/question/20639242
#SPJ4
The major types of stress are Shear, Tension and Compression. The correct option is D.
Thus, Shear stress, tension stress, and compression stress are the three main forms of stress.
Shear stress is a condition when forces acting in opposite directions and parallel to a surface cause the material to deform by sliding or shearing. It is connected to the propensity for one layer of material to slide or move in relation to another layer.
Tension stress, sometimes referred to as tensile stress, is the strain that develops when a material is subjected to pulling or stretching forces that are applied in opposition to one another, causing the material to elongate. The material tends to be pulled apart by tension stress.
Thus, The major types of stress are Shear, Tension and Compression. The correct option is D.
Learn more about Shear stress, refer to the link:
https://brainly.com/question/20630976
#SPJ12