Answer:
a) Thermometer
b) Fractionating Column
c) Found-bottom Flask
d) Mask
e) Bunsen Burner
f) Water Out
g) Condenser
h) Water In
Set-up A: Reflux Set-up
Set-up B: Distillation Set-up
d) The purpose of using a reflux condenser in organic synthesis is to prevent the loss of volatile reactants or products. During a reflux reaction, the reactants are continuously heated, and the vapors are condensed and returned to the reaction vessel, which allows the reaction to proceed for an extended period without losing any material to the atmosphere. The reflux condenser also helps to maintain a constant temperature and prevent overheating.
(please could you kindly mark my answer as brainliest)
1) In this experiment, you will be mixing aqueous solutions of sodium carbonate and calcium chloride to produce solid calcium carbonate.
Na CO2 (aq) +CaCl(aq) — 2 NaCl(aq) +CaCO3
Order the steps required to predict the volume (in mL) of 0. 200 M sodium carbonate needed to produce 2. 00 g of calcium carbonate. There is an excess of calcium chloride.
Comp
Identi
volum
2
>
Calcu
Check
>
Step 1
Convert mass of calcium carbonate 10 moles of calcium carbonate
Step 2
Compare moles of calcium carbonate to moles of sodium carbonate based on balanced equation to calculate moles of sodium carbonate required
Step 3
Compute the volume of sodium carbonate solution required
Step 4
Convert the volume of sodium carbonate solution required from liters to milliers
2) Na2CO3(aq) + CaCl2(ag) + 2NaCl(aq) + CaCO3(-)
Calculate the volume (in mL) of 0. 200 M Na2CO, needed to produce 2. 00 g of CaCO3(s). There is an excess of CaCl.
Molar mass of calcium carbonate = 100. 09 g/mol
Volume of sodium carbonate - 100 mL
METHODS
RESET
MY NOTES
A LAB DATA
Based on the information provided, the correct order of steps required to predict the volume of 0.200 M sodium carbonate needed to produce 2.00 g of calcium carbonate is:
Step 1: Identify the molar mass of calcium carbonate (CaCO3)
Step 2: Convert the given mass of calcium carbonate to moles using its molar mass
Step 3: Use the balanced chemical equation to determine the mole ratio between calcium carbonate and sodium carbonate
Step 4: Calculate the amount of moles of sodium carbonate required
Step 5: Convert the moles of sodium carbonate to volume in liters using its molarity
Step 6: Convert the volume in liters to milliliters
Therefore, the correct order of steps is:
Step 1: Identify
Step 2: Convert
Step 3: Compute
Step 4: Convert
Step 5: Convert
Step 6: Check
Using the given information, the calculation can be done as follows:
Step 1: The molar mass of calcium carbonate (CaCO3) is given as 100.09 g/mol.
Step 2: The given mass of calcium carbonate is 2.00 g. Therefore, the number of moles of calcium carbonate can be calculated as follows:
2.00 g / 100.09 g/mol = 0.01998 mol ≈ 0.020 mol
Step 3: According to the balanced chemical equation, the mole ratio between calcium carbonate and sodium carbonate is 1:1. Therefore, the amount of moles of sodium carbonate required is also 0.020 mol.
Step 4: The molarity of the sodium carbonate solution is given as 0.200 M. Therefore, the volume of sodium carbonate solution required in liters can be calculated as follows:
0.020 mol / 0.200 mol/L = 0.100 L = 100 mL
Step 5: The volume in liters needs to be converted to milliliters:
0.100 L x 1000 mL/L = 100 mL
Step 6: Check the answer to make sure it is reasonable and makes sense.
To know more about sodium carbonate, visit: brainly.com/question/13565765
#SPJ4
(science) explain the difffrence between a food chain and a food web
Answer: A food chain shows what eats what. A food web is made up of all the food chains in the ecosystems.
Explanation: Hope that helps!
Answer:
Explanation:
A food chain outlines who eats whom.
A food web is all of the food chains in an ecosystem.
Arrange these species by their ability to act as an oxidizing agent. Best oxidizing agent Au3+ Fe2+ Ni2+ Na+ Poorest oxidizing agent Answer Bank
The correct order of species based on their ability to act as an oxidizing agent is Au3+ > Fe2+ > Ni2+ > Na+.
The ability to act as an oxidizing agent varies among different species. In the given set of species, the order of their ability to act as an oxidizing agent from the best to the poorest is as follows:
Au3+ > Fe2+ > Ni2+ > Na+
Au3+ is the best oxidizing agent as it has the maximum tendency to accept electrons and undergo reduction.
Fe2+ is a better oxidizing agent than Ni2+ and Na+ because it can accept two electrons easily and undergoes reduction. Ni2+ is a weaker oxidizing agent than Fe2+ and Na+ as it can only accept electrons and undergoes reduction. Na+ is the poorest oxidizing agent as it has the least tendency to accept electrons and undergo reduction. It is the best reducing agent as it readily donates an electron to become Na.
For more such questions on oxidizing agent, click on:
https://brainly.com/question/14041413
#SPJ11
Which of the following is not true regarding the competitive dynamics of most sharing economy marketplaces?
Late-movers have a substantial advantage in this market since inventory should be cheaper to acquire for those firms that have entered markets more recently
"Late-movers have a substantial advantage in this market since inventory should be cheaper to acquire for those firms that have entered markets more recently" is not true regarding the competitive dynamics. This is because late-movers face many challenges.
What is sharing economy?Sharing economy refers to a peer-to-peer (P2P) networking concept where consumers and organizations have the opportunity to share, sell, or rent products and services to one another directly without the involvement of middlemen. The sharing economy includes various industries, such as ride-sharing, accommodation-sharing, co-working spaces, and others.
The competitiveness of a sharing economy marketplace is influenced by factors such as the number of competitors, the level of brand recognition, pricing strategies, product quality, customer service, and others. When new entrants join a sharing economy market, existing players will have to adjust to remain competitive. Therefore, it is vital for market participants to monitor the competition's tactics and come up with new strategies to stay ahead of the curve.
However, late-movers do not have a substantial advantage in this market since inventory should be cheaper to acquire for those firms that have entered markets more recently is not true regarding the competitive dynamics of most sharing economy marketplaces.
Learn more about Sharing economy here:
https://brainly.com/question/29361595
#SPJ11
Can you explain in terms of Le Chatelier's principle why the concentration of NH3 decreases when the temperature of the equilibrium system increases?
Le Chatelier's principle predicts that when a stress or change is added to a system at equilibrium, the system will adjust in order to counteract the stress or change. The principle can be used to describe the shift in the direction of the chemical equilibrium in response to changes in pressure, temperature, or concentration.
What is Le Chatelier's principle?Le Chatelier's principle states that when the temperature is increased, the equilibrium system will absorb the heat by shifting the equilibrium position in the direction that uses up the heat energy. If heat is a product of the reaction, the equilibrium will shift to the left. If heat is a reactant, the equilibrium will shift to the right.
Here, in the case of the reaction of nitrogen and hydrogen to create ammonia:
N₂(g) + 3H₂(g) ⇌ 2NH₃(g), ∆H = −92 kJ/mol
The reaction produces heat, therefore the reaction is exothermic. An increase in temperature will cause a shift in equilibrium to the left, as the reaction will try to use up the excess heat. This means that the reaction will reduce the amount of NH₃ in the system, leading to a decrease in the concentration of NH₃.
Learn more about Le Chatelier's Principle here:
https://brainly.com/question/29009512
#SPJ11
Calculate the amount of heat needed to boil 132.g of water (H20), beginning from a temperature of 7.4 °C. Round your answer to 3 significant digits. Also, be sure your answer contains a unit symbol
62.297 kJ of heat is required to boil 132.g of water (H20), beginning from a temperature of 7.4 °C.
The quantity of heat required to boil 132 g of water at a temperature of 7.4°C is to be calculated. The heat energy required to increase the temperature of a material by one degree Celsius is referred to as heat capacity or specific heat. The formula for specific heat capacity is given by Q = mCΔT where Q is the quantity of heat, m is the mass of the material, C is the specific heat capacity of the material, and ΔT is the difference in temperature.
We'll utilise the following formula to calculate the heat required:q = m x c x ΔT + m x Lwhere q is the quantity of heat, m is the mass of the material, c is the specific heat of the material, ΔT is the difference in temperature, and L is the material's latent heat of vaporization.
The value of q can now be calculated : q = (132.0 g) × (4.184 J/g°C) × (100°C – 7.4°C) + (132.0 g) × (2.26 × 106 J/kg)q = 62297.0 J. The heat required to boil 132 g of water beginning at 7.4°C is 62297.0 J. This means that 62.297 kJ of heat is required.
Know more about specific heat capacity here:
https://brainly.com/question/29766819
#SPJ11
A certain half-reaction has a standard reduction potential EPod=-0.75 V. An engineer proposes using this half-reaction at the cathode of a galvanic cell that must provide at least 0.90 V of electrical power. The cell will operate under standard conditions. Note for advanced students: assume the engineer requires this half-reaction to happen at the cathode of the cell. Is there a minimum standard reduction potential that the half-reaction used at the anode of this cell can have? Is there a maximum standard reduction potential that the half-reaction used at the anode of this cell can have? By using the information in the ALEKS Data tab, write a balanced equation describing a half reaction that could be used at the anode of this cell. Note: write the half reaction as it would actually occur at the anode.
Using the following formula, the total cell potential, Ecell, may be calculated: Ecathode + anode equals Ecell. where Ecathode is the cathode half-reduction reaction's potential and Eanode.
We can determine the minimal Eanode needed to create a cell potential of 0.90 V since the engineer suggests employing a half-reaction with EPod = -0.75 V at the cathode:
Ecathode + anode equals Ecell.
Eanode: 0.90 V = -0.75 V
Eanode = 0.75 0.90 volts
Eanode equals 1.65 V.
The half-reaction employed at the anode must thus have a standard reduction potential of -1.65 V or less.
The typical reduction potential of the half-reaction utilised at the anode, on the other hand, has no upper limit. Yet, a higher Ecell and a more effective galvanic cell would be produced by a larger reduction potential at the anode.
We can utilise the half-reaction to create a balanced equation for the anode half-reaction:
Cu(s) becomes Cu2+(aq) plus 2e-
learn more about half-oxidation reaction's potential.here:
https://brainly.com/question/23302600
#SPJ4
When ammonia reacts with oxygen, nitrogen monoxide and water are produced. The balanced equation for this reaction is: 4NH3 (g) + 5O2 (g) 4NO (g) + 6H2O (g) If 16 moles of ammonia react, The reaction consumes moles of oxygen The reaction produces moles of nitrogen monoxide and moles of water
The reaction consumes 20 moles of oxygen, and it produces 16 moles of nitrogen monoxide and 24 moles of water.
What is mole?
The quantity amount of substance is a measure of how many elementary entities of a given substance are in an object or sample. The mole is defined as containing exactly 6.022×10²³ elementary entities.
When ammonia reacts with oxygen, the balanced equation is:
4NH3(g) + 5O2(g) → 4NO(g) + 6H2O(g)
It is known that 16 moles of ammonia react, and we have to calculate the moles of oxygen, nitrogen monoxide, and water produced by the reaction.
The balanced equation shows that 4 moles of NH3 react with 5 moles of O2 to produce 4 moles of NO and 6 moles of H2O.
According to the stoichiometry of the reaction, 16 moles of NH3 will react with
(5/4) × 16 = 20 moles of O2
Hence, the reaction consumes 20 moles of oxygen.
The balanced equation shows that 4 moles of NH3 react with 4 moles of NO to produce 4 moles of NO and 6 moles of H2O.
According to the stoichiometry of the reaction, 16 moles of NH3 will produce
(4/4) × 16 = 16 moles of NO
Hence, the reaction produces 16 moles of nitrogen monoxide.
The balanced equation shows that 4 moles of NH3 react with 6 moles of H2O to produce 4 moles of NO and 6 moles of H2O.
According to the stoichiometry of the reaction, 16 moles of NH3 will produce
(6/4) × 16 = 24 moles of H2O
Hence, the reaction produces 24 moles of water.
Learn more about moles on:
https://brainly.com/question/29367909
#SPJ11
an exothermic chemical reaction between a solid and a liquid results in gaseous products. spontaneous?
An exothermic chemical reaction between a solid and a liquid results in gaseous products. It is a spontaneous reaction.
What is an exothermic reaction?When a chemical reaction takes place with the release of heat, it is known as an exothermic chemical reaction. An exothermic chemical reaction is a chemical reaction that releases energy in the form of heat, light, or sound during the process. The burning of paper is an example of an exothermic chemical reaction. When paper burns, heat and light are produced, which we can feel or observe.
The reaction is spontaneous if the Gibbs free energy, delta G is negative. A reaction will be spontaneous if its delta G is negative. The reaction will proceed from left to right if delta G is negative, and it will proceed from right to left if delta G is positive. A reaction will be at equilibrium if delta G is zero.The reaction mentioned in the question is an exothermic chemical reaction because it results in the release of heat. As a result, the reaction is spontaneous. The production of gaseous products indicates that a gas is formed during the reaction. Therefore, this reaction is spontaneous.
Learn more about Exothermic reaction here:
https://brainly.com/question/10373907
#SPJ11
In 1828, Friedrich Wöhler produced urea
when he heated a solution of ammonium
cyanate. This reaction is represented by the
balanced equation below.
H 7+
H-N-H[C=N-O]
I
H
Ammonium
cyanate
H O
\/
N-CIN
H
Urea
Explain why this balanced equation represents a
conservation of atoms.
H
H
This balanced equation represents the principle of conservation of atoms, which is a fundamental principle of chemistry in the sense that the number and type of atoms are the same on both sides which means that no atoms were created or destroyed during the reaction, only rearranged to form new molecule.
What is a balanced equation?A balanced equation is described as an equation for a chemical reaction in which the number of atoms for each element in the reaction and the total charge are the same for both the reactants and the products.
Analyzing the diagram,
On the left-hand side we have :1 nitrogen atom (N)
3 hydrogen atoms (H)
1 carbon atom (C)
2 oxygen atoms (O)
On the right-hand side:1 nitrogen atom (N)
4 hydrogen atoms (H)
1 carbon atom (C)
2 oxygen atoms (O)
This can only mean that no atoms were created or destroyed during the reaction, only rearranged to form new molecules.
Learn more about balanced equation atr:
https://brainly.com/question/11904811
#SPJ1
Match each equation for calculating heat lost or gained (q) during a process to its correct application. Drag statements on the right to match the left. Heating or cooling within a phase if moles are given C- q = nCAT Heating or cooling during a phase change D-a 9 = NAH change Heating or cooling within a phase if mass is given CHO q=mcAT
The correct match are: q = nCAT for Heating or cooling within a phase if moles are given, q = NAΔH for Heating or cooling during a phase change, and q = mcΔT for Heating or cooling within a phase if mass is given.
What is the heat loss during phase change?q = nCAT is used to calculate Heat lost or gained when heating or cooling within a phase if moles are given. In this equation, n is the number of moles, C is the heat capacity of the substance, A is the temperature change.
q = NAΔH is used to calculate Heat lost or gained when heating or cooling during a phase change. In this equation, N is the number of moles, ΔH is the enthalpy of fusion or vaporization.
q = mcΔT is used to calculate Heat lost or gained when heating or cooling within a phase if mass is given. In this equation, m is the mass of the substance, c is the specific heat capacity of the substance, ΔT is the temperature change.
Learn more about Phase change here:
https://brainly.com/question/30270780
#SPJ11
What is unique about carbons valence shell?
Answer: Carbon's valence shell is unique because it has 4 valence shell electrons, which means it is less likely to gain or lose electrons to other elements. Rather, it shares its electrons. In other words, it tends to form covalent bonds (4) rather than ionizing. This results in carbon being able to form long chains or rings.
which type of atomic orbital can be described as having 2 lobes of electron density separated by a nodal plane?
The type of atomic orbital that can be described as having 2 lobes of electron density separated by a nodal plane is the P orbital.
In atomic theory, an atomic orbital is a mathematical function that describes the behavior of one electron in an atom. It is a region in space with a high probability of locating an electron.
There are 3 types of orbitals available in each sub-shell of an atom. The sub-shell in each shell can be used to predict the number of orbitals.
There are 1 s-orbital, 3 p-orbitals, 5 d-orbitals, and 7 f-orbitals available in the first, second, and third shells, respectively. The type of atomic orbital that can be described as having 2 lobes of electron density separated by a nodal plane is the P orbital.
Each P orbital has two lobes of electrons located on either side of the nucleus separated by a nodal plane. The lobes can be polarized, making them more or less prominent depending on the situation.
This configuration provides the P orbital with a unique geometry and makes it highly suitable for molecular bonding.
The P orbital has a total of three different orientations. Each orientation corresponds to a different direction in space in which the lobes can be located. The three orientations are Px, Py, and Pz.
Each P orbital can hold a maximum of 2 electrons.
To know more about atomic orbitals, refer here:
https://brainly.com/question/28240666#
#SPJ11
tums tablet has a mass of 0.565 g. a 0.196 g piece of the tablet is found to contain 0.123 g of ca. what is the mass (in grams) of ca in the whole tablet? be sure to give the proper number of significant figures in your answer
The mass of Ca is 0.355 g.
Tums tablet has a mass of 0.565 g.
A 0.196 g piece of the tablet is found to contain 0.123 g of Ca.
Mass percent = (Mass of element in the compound / Mass of the compound) × 100
The mass of Ca in the given piece is,
The mass percent of Ca = (Mass of Ca in the given piece / Mass of the given piece) × 100
= (0.123 / 0.196) × 100 = 62.75510204 %
This means, in every 100 grams of Tums tablet, Ca is present in 62.75510204 grams (approximately).
Therefore, the mass of Ca in 0.565 g of Tums tablet is,
Mass of Ca in 0.565 g of Tums tablet = 0.565 × (62.75510204 / 100) = 0.3546475852 g ≈ 0.355 g
The mass (in grams) of Ca in the whole tablet is approximately 0.355 g.
To learn more about the mass of elements refer - https://brainly.com/question/22139340
#SPJ11
2. For each of the reactions below, write a structural reaction equation (which need not be balanced) by
drawing the structures of the reactant & product and name the product formed.
a) ethanol + K,Cr₂O, / H / reflux
b) ethanol + K₂Cr₂O, / H / distil
c) propan-1-ol + K,Cr₂O,/H. / reflux
d) propan-2-ol + K,Cr,O,/ H / reflux
e) 3-methylbutan-1-ol + K,Cr₂O, / H / reflux
f) 4-chloropentan-1-ol + K₂Cr₂O,/ H / distil
Answer:
a) Ethanol + K2Cr2O7 / H+ / Reflux → Acetaldehyde
CH3CH2OH + [O] → CH3CHO
b) Ethanol + K2Cr2O7 / H+ / Distil → Ethene
CH3CH2OH + [O] → CH2=CH2 + H2O
c) Propan-1-ol + K2Cr2O7 / H+ / Reflux → Propanal
CH3CH2CH2OH + [O] → CH3CH2CHO
d) Propan-2-ol + K2Cr2O7 / H+ / Reflux → Propanone (acetone)
(CH3)2CHOH + [O] → (CH3)2CO
e) 3-Methylbutan-1-ol + K2Cr2O7 / H+ / Reflux → 3-Methylbutanal
CH3CH(CH3)CH2CH2OH + [O] → CH3CH(CH3)CH2CHO
f) 4-Chloropentan-1-ol + K2Cr2O7 / H+ / Distil → 4-Chloropentanal
Cl(CH2)3CH2CH(OH)CH3 + [O] → Cl(CH2)3CH2CH=O + H2O
(please could you kindly mark my answer as brainliest)
Which organism provides energy to all other organisms in this ecosystem?
coyote
prarie grass
vulture
prarie dog
Answer:
The organism that provides energy to all other organisms in an ecosystem is usually a primary producer, which is an organism that produces its own food through photosynthesis or chemosynthesis. In this ecosystem, the primary producer is likely the prairie grass, as it converts sunlight into energy through photosynthesis and is the basis of the food chain. The other organisms listed (coyote, vulture, prairie dog) are consumers and obtain their energy by eating other organisms, either directly or indirectly.
(please could you kindly mark my answer as brainliest )
10 ml of ethanol is mixed with 250 ml of water calculate the volume percentage of ethanol
Answer: 3.85%
Explanation: To calculate the volume percentage of ethanol in the mixture, we need to determine the total volume of the mixture first.
Total volume = volume of ethanol + volume of water
Total volume = 10 ml + 250 ml
Total volume = 260 ml
Now, we can calculate the volume percentage of ethanol in the mixture using the following formula:
Volume percentage of ethanol = (volume of ethanol ÷ total volume) x 100%
Plugging in the values, we get:
Volume percentage of ethanol = (10 ml ÷ 260 ml) x 100%
Volume percentage of ethanol = 3.85%
Therefore, the volume percentage of ethanol in the mixture is 3.85%.
"Oxygen candles" release breathable oxygen (O) through the chemical decomposition of potassium chlorate or related compounds. These devices are used to provide emergency oxygen sources to aircraft passengers, firefighters, miners, and astronauts. Use your balanced equation from question 1 to calculate the mass of KCIO, needed for an oxygen candle to provide a one-day supply of oxygen if the average adult consumes 909 g of 0, per day.
Answer:
The balanced equation for the decomposition of potassium chlorate is:
2KClO3 → 2KCl + 3O2
This equation tells us that for every 2 moles of KClO3 that decompose, 3 moles of O2 are produced.
To calculate the mass of KClO3 needed to produce a one-day supply of oxygen for an adult, we first need to calculate the amount of oxygen consumed per day by an average adult. We are given that the average adult consumes 909 g of O2 per day.
We can use the molar mass of O2 to convert grams to moles:
1 mol O2 = 32 g
909 g O2 = 28.4 mol O2
Next, we need to determine how much KClO3 is needed to produce 28.4 mol of O2. From the balanced equation, we know that 2 moles of KClO3 are needed to produce 3 moles of O2.
So, the number of moles of KClO3 needed is:
(28.4 mol O2) × (2 mol KClO3/3 mol O2) = 18.93 mol KClO3
Finally, we can use the molar mass of KClO3 to convert moles to grams:
1 mol KClO3 = 122.55 g
18.93 mol KClO3 = 2,322 g KClO3
Therefore, to provide a one-day supply of oxygen for an adult consuming 909 g of O2 per day, an oxygen candle would need approximately 2,322 grams of potassium chlorate.
problem set organic chemistry. in each reaction identify homo of the nucleophile and lumo of electrophile
The homo of the nucleophile in a reaction set for organic chemistry is the highest occupied molecular orbital (HOMO), which is the highest energy orbital that contains at least one electron.
The lowest unoccupied molecular orbital (LUMO) of the electrophile is the lowest energy orbital that does not contain any electrons.
When attempting a reaction set for organic chemistry, the HOMO of the nucleophile will react with the LUMO of the electrophile to form a new bond. The HOMO is considered to be the electron-rich species and the LUMO is considered to be the electron-poor species.
This interaction between the two species leads to the formation of the new bond. The nature of the new bond is determined by the nature of the two species.
If the two species are of the same element, the bond is covalent. If the two species are of different elements, the bond is polar covalent or ionic depending on the difference in electronegativity between the two species.
To know more about nucleophile click on below link:
https://brainly.com/question/28325919#
#SPJ11
What would you predict, the solubility of KHT (solid) in pure water compared with the solubility of KHT (solid) in a 0.1 M KCl solution, which one will be higher? Explain your answer
The solubility of KHT (solid) in pure water compared with the solubility of KHT (solid) in a 0.1 M KCl solution will be higher in a 0.1 M KCl solution. KCl is an electrolyte, which is a substance that dissociates into ions when it is dissolved in water. The presence of these ions can affect the solubility of other substances in the solution, which is known as the
common-ion effect.The common-ion effect is the reduction in the solubility of a substance due to the presence of a common ion in the solution. In this case, KCl contains K+ ions, which are also present in KHT. When KCl is dissolved in
water, it dissociates into K+ and Cl- ions. The K+ ions from KCl can react with the KHT and form the insoluble salt KHT. As a result, the solubility of KHT in the solution is reduced.In pure water, there are no K+ ions present, so the solubility
of KHT will be higher. However, in a 0.1 M KCl solution, the presence of K+ ions from KCl will decrease the solubility of KHT. Therefore, the solubility of KHT in a 0.1 M KCl solution will be lower than in pure water.
For more similar questions on topic Solubility equilibria.
https://brainly.com/question/14409825
#SPJ11
What kind of system is an exploded hydrogen balloon?
A. Isolated system
B. Closed system
C. Open system
D. No way to tell
An exploded hydrogen balloon is an example of an open system (option C).
What is an open system?An open system is a system that can exchange both matter and energy with its surroundings. In an open system, there is a flow of matter and energy in and out of the system. This means that the system is not isolated from its environment, and it interacts with the outside world.
An exploded hydrogen balloon is an example of an open system because during the explosion, the system (which includes the balloon and the hydrogen gas inside) releases matter (hydrogen gas) and energy (in the form of heat and sound) into the surrounding environment.
Learn about An open system here https://brainly.com/question/5054863
#SPJ1
a solution is prepared by mixing 736.0 ml of ethanol with 694.0 ml of water. the molarity of ethanol in the resulting solution is 9.186 m. the density of ethanol at this temperature is 0.7893 g/ml. calculate the difference in volume between the total volume of water and ethanol that were mixed to prepare the solution and the actual volume of the solution.
The volume difference between the total volume of water and ethanol that were mixed to prepare the solution and the actual volume of the solution is 538.56 ml.
What is the volume difference?To calculate the volume difference, we need to first calculate the total volume of the solution and the volume of each component in the solution.
The total volume of the solution is the sum of the volumes of ethanol and water:
Total volume = volume of ethanol + volume of water
Total volume = 736.0 ml + 694.0 ml
Total volume = 1430.0 ml
To calculate the volume of ethanol in the solution, we need to convert the mass of ethanol to volume using its density:
Mass of ethanol = volume of ethanol x density of ethanol
Volume of ethanol = mass of ethanol / density of ethanol
Volume of ethanol = (9.186 mol/L) x (0.7893 g/ml) x (736.0 ml) / (46.07 g/mol)
Volume of ethanol = 197.44 ml
Similarly, we can calculate the volume of water in the solution:
Volume of water = 694.0 ml
Therefore, the actual volume of the solution is the sum of the volumes of ethanol and water:
Actual volume of solution = volume of ethanol + volume of water
Actual volume of solution = 197.44 ml + 694.0 ml
Actual volume of solution = 891.44 ml
The volume difference is the difference between the total volume of ethanol and water that were mixed and the actual volume of the solution:
Volume difference = Total volume - Actual volume of solution
Volume difference = 1430.0 ml - 891.44 ml
Volume difference = 538.56 ml
Learn more about volume difference here: https://brainly.com/question/21305745
#SPJ1
The phenomenon in which electrons that are closer to the nucleus slightly repel those that are farther out, is known as: select the correct answer below: - shielding - deflecting - building up - converging
The phenomenon in which electrons that are closer to the nucleus slightly repel those that are farther out is known as Shielding.
Electrons in an atom are negatively charged particles, and they are attracted to the positively charged nucleus. However, the outer electrons of an atom are also repelled by the inner electrons that are closer to the nucleus. This repulsion is due to the negative charges of the electrons, and it partially cancels out the attraction of the nucleus for the outer electrons.
Shielding is the phenomenon in which electrons that are closer to the nucleus slightly repel those that are farther out. This makes it possible for electrons in higher energy levels to be farther from the nucleus, so they are less strongly attracted and easier to remove.
Learn more about Shielding here: https://brainly.com/question/27985711
#SPJ11
What volume of 0.125 M HNO3, in milliliters, is required to react completely with 1.70 g of Ba(OH)2? 2 HNO3(aq) + Ba(OH)2(s) Ba(NO3)2(aq) + 2 H2O(l)
Answer:
What volume of 0.125 M HNO3, in milliliters, is required to react completely with 1.70 g of Ba(OH)2? 2 HNO3(aq) + Ba(OH)2(s) Ba(NO3)2(aq) + 2 H2O(l)
Explanation:
The complete and balanced chemical equation for the reaction of nitric acid
H
N
O
3
with barium hydroxide
B
a
(
O
H
)
3
is given by
2
H
N
O
3
(
a
q
)
+
B
a
(
O
H
)
2
→
B
a
(
N
O
3
)
2
(
a
q
)
+
2
H
2
O
(
a
q
)
The volume of a certain concentration of nitric acid
H
N
O
3
required to react with a particular amount of
B
a
(
O
H
)
2
is obtained by first calculating the number of moles of
H
N
O
3
using stoichiometry. Using the molar mass of
B
a
(
O
H
)
2
,
M
M
B
a
(
O
H
)
2
=
171.3
g
/
m
o
l
,
and the mole ratio
2
m
o
l
H
N
O
3
1
m
o
l
B
a
(
O
H
)
2
,
then
{eq}\begin{align} \rm moles\ of\ HNO_3...
hope it hels you
Explain the following statement about the rate law equation: The rate constant isn't really
constant. Include the definition of the term rate constant in your answer and give two
specific examples to support this statement.
Answer:
In chemical kinetics, the rate constant (k) is a proportionality constant that relates the rate of a chemical reaction to the concentrations of the reactants. It is often included in the rate law equation, which expresses the relationship between the rate of the reaction and the concentrations of the reactants.
However, the rate constant is not truly constant because it can vary with different experimental conditions. The rate constant is affected by factors such as temperature, pressure, and the presence of catalysts or inhibitors. For example, an increase in temperature usually leads to an increase in the rate constant, while the addition of a catalyst can decrease the activation energy and increase the rate constant.
Two specific examples that support this statement are:
1) The effect of temperature on the rate constant: Consider the reaction A → B, which has a rate law equation of rate = k[A]. If the temperature is increased, the rate constant will increase due to the increase in kinetic energy of the reactant molecules. This means that the reaction will proceed faster at higher temperatures, even if the concentration of A remains the same.
2) The effect of catalysts on the rate constant: Consider the reaction C + D → E, which has a rate law equation of rate = k[C][D]. If a catalyst is added to the reaction, it can increase the rate constant by providing an alternate pathway with a lower activation energy. This means that the reaction will proceed faster at the same concentrations of C and D with the catalyst present than without it.
Explanation:
How many milliliters of 1.58 M HCl are needed to react completely with 23.2 g of NaHCO3 (= 84.02 g/mol)?
HCl(aq) + NaHCO3(s) ? NaCl(s) + H2O(l) + CO2(g)
a. 175 mL
b. 536 mL
c. 276 mL
d. 572 mL
e. 638 mL
c. 276 mL of 1.58 M HCl.
To answer this question, we need to use the mole ratio between the two reactants: 1 mole of HCl for every 1 mole of NaHCO3.
In this case, we need 23.2 g of NaHCO3, which is equal to 0.273 moles (23.2 g / 84.02 g/mol).
Since we need 1 mole of HCl for every 1 mole of NaHCO3, we can calculate the number of moles of HCl needed with the following equation: 0.273 moles of NaHCO3 x 1 mole HCl/1 mole NaHCO3 = 0.273 moles of HCl.
Now we can use the molarity of HCl (1.58 M) to calculate the volume of HCl needed. 1.58 M HCl x 0.273 moles HCl/1 L HCl = 0.433 L HCl, or 433 mL of HCl. Therefore, the correct answer is c. 276 mL of 1.58 M HCl.
To know more about mole ratio, refer here:
https://brainly.com/question/28997213#
#SPJ11
write each of the following as an empirical formula. if it is already an empirical formula, put a check mark. c4h1006 1) al(so3)1.5 ch3 fe(no3)3
Answer:
The empirical formula for C₄H₁₀0₆ is CH₂O
The empirical formula for Al(SO₃)1.5 is Al₂(SO₄)3
The empirical formula for CH₃ is already given.
The empirical formula for Fe(NO₃)3 is already given.
Explanation: Empirical formula is the simplest formula that gives the simplest whole number ratio of atoms in a compound.
To get the empirical formula, the given formula must be reduced to its simplest whole-number ratio. For this, divide each subscript by the largest common factor.
Hence, the empirical formulae for the given formulas are,
The empirical formula for C₄H₁₀0₆ is CH₂O
The empirical formula for Al(SO₃)1.5 is Al₂(SO₄)3
The empirical formula for CH₃ is already given.
The empirical formula for Fe(NO₃)3 is already given.
Learn more about empirical formulas here:
https://brainly.com/question/1439914
#SPJ11
when the carbonyl group of a neutral ketone is protonated . group of answer choices = a.the resulting species becomes more electrophilic.
b. subsequent nucleophilic attack on the resulting species is said to occur under acid-catalyzed conditions.
c. the resulting species is activated toward nucleophilic attack.
d. all of the above.
e. the resulting species has a positive charge.
The correct answer is d All of the above
The protonation of a neutral ketone creates an electrophilic species that is activated toward nucleophilic attack, which is said to occur under acid-catalyzed conditions.
Therefore, All of the above are true: the resulting species becomes more electrophilic, subsequent nucleophilic attack on the resulting species is said to occur under acid-catalyzed conditions, and the resulting species has a positive charge.
Wat is a ketone?A ketone is an organic compound with a carbonyl group (CO) bound to two other carbon atoms.
The chemical formula for a ketone is RCOR′, where R and R′ can be any group from the periodic table.
Ketones are classified as carbonyl compounds since they contain a functional group with a carbon atom double-bonded to an oxygen atom.
When the carbonyl group of a neutral ketone is protonated, the resulting species is activated toward nucleophilic attack.
When the group of a neutral ketone is protonated, the carbonyl carbon atom acquires a partial positive charge, and the oxygen acquires a partial negative charge
As a result, the carbonyl carbon atom becomes more electrophilic than before. The carbonyl group of the resulting species is more prone to nucleophilic attack than it was in the original ketone. The nucleophile can be a negative ion or a lone pair of electrons.
Subsequent nucleophilic attack on the resulting species is said to occur under acid-catalyzed conditions.
For more information about ketone protonation refer here
https://brainly.com/question/28205796
#SPJ11
True or False : The manipulated variable is the same thing as the independent variable.
Answer:
True.
The manipulated variable and the independent variable refer to the same thing in an experiment. It is the variable that is intentionally changed or manipulated by the experimenter to observe its effect on the dependent variable.
the rate of a second order reaction can depend on the concentrations of more than one reactant. the rate of a second order reaction can depend on the concentrations of more than one reactant. true false g
The given statement that "the rate of a second order reaction can depend on the concentrations of more than one reactant" is true because the rate of the reaction is proportional to the concentration of both reactants.
What is a second-order reaction?The second-order reaction is a chemical reaction in which two reactants interact and the rate of the reaction is proportional to the concentration of both reactants or to the square of the concentration of a single reactant. The equation is as follows:
k = k[reactant1] [reactant2] or k = k[reactant1]²
The reaction rate constant (k) for a second-order reaction is proportional to the concentration of one or two reactants. The concentration of the reactants has an impact on the reaction rate, as indicated by the order of the reaction.
Therefore, the statement that "the rate of a second order reaction can depend on the concentrations of more than one reactant" is true.
Learn more about second-order reaction here: https://brainly.com/question/14520581.
#SPJ11