The basic law concerning transformers is the law of conservation of energy, which states that energy can neither be created nor destroyed, only transformed from one form to another.
What is transformers?
Transformers are electronic devices that are used to change the voltage, current, or frequency of alternating current (AC) electricity. They are important components in electrical power systems, allowing power to be transmitted over long distances and between different voltage levels. Transformers consist of two coils of wire, known as the primary and secondary windings, with an iron core in the middle that serves to link the two coils together. When an alternating current is applied to the primary winding, it creates an alternating magnetic field, which in turn induces a voltage in the secondary winding.
To learn more about transformers
https://brainly.com/question/29665451
#SPJ4
If extension done in a stork position, during backward bending in a standing position of a special test for lumbar spine, produces pain in the lumbar or sacral regions of the spine, it may indicate _____.
P=3000W
f1=0.9
f2=0.5
A=15mm2
travel speed=?
The Travel Speed at which the welding operation can be accomplished is given as 7.147mm/s. See the computation below.
What is travel speed?The travel speed of the welding flame or gun across the workpiece is simply measured in millimeters per minute.
Travel speed, along with voltage and amperage, is one of three factors in arc welding that affect the amount of heat input.
What is the calculation that justifies the above answer is?We are given the following:
Melting temperature = 1650 K
k = (3.33 * 10⁻⁶) * (1,650)²
k = 9.066 J/mm^3
The formula for velocity here is given as:
V = f1 * f2 * Rh / (k*A)
V = 0.9 * 0.6 * 3000 / (9.066*25)
V = 7.147 mm/s
Hence, the Travel Speed at which the welding operation can be accomplished is given as 7.147mm/s.
Learn more about welding operation at;
https://brainly.com/question/22494632
#SPJ1
A wheel spins at a constant angular speed of 24rad/s.How many revolutions will the dosk go through in 5minutes?
Answer:
The wheel will go through 1146 revolutions in 5 minutes.
Explanation:
We can the formula:
[tex]\boxed{\omega = \frac{2 \pi}{T}}[/tex]
where
ω ⇒ angular speed (24 rad/s),
T ⇒ time period (? s),
and solve for T to find the time it takes for the wheel to complete one revolution.
⇒ [tex]24 = \frac{2 \pi}{T}[/tex]
⇒ [tex]T = \bf \frac{2 \pi}{24}[/tex] s
This means it takes [tex]\bf \frac{2 \pi}{24}[/tex] seconds for the wheel to complete one revolution.
Now, using the unitary method,
In [tex]\frac{2 \pi}{24}[/tex] seconds ⇒ 1 revolution completed
In 1 second ⇒ 1 ÷ [tex]\frac{2 \pi}{24}[/tex] = [tex]\frac{24}{2 \pi}[/tex] revolutions completed
In (5 × 60 = ) 300s ⇒ [tex]\frac{24}{2 \pi}[/tex] × 300 = 1145.9
≅ 1146 revolutions completed
The only difference between all GMA welding machines and some FCA welding machines is that all GMA welding machines must have a ______________.
Answer: Shielding gas solenoid
Explanation:
An inverter has a balanced 3-phase, 277/480 V output and is installed a distance, d, ft from the point of utility connection. The DC/AC converter shown below in the inverter. And the distance d is the physical separation between this DC/AC converter and the PCC. (
An expression for the voltage drop between inverter and PUC
[tex]V D \rightarrow \frac{I(\Omega / k f t) d}{2770}$[/tex]
This is further explained below.
What is an expression for the voltage drop between the inverter and PUC?Generally, the equation for Voltage drop is mathematically given as
[tex]V=\frac{I R}{V}[/tex]
Therefore
[tex]\%$ Voltage drop $=\frac{I R}{V} * 100\\\\$\rightarrow \frac{100 I(\Omega / 15 f t) d}{1000 V_{p}}\\\\$V_{P}=277 \mathrm{~V}$[/tex]
[tex]V D=\frac{I(\Omega / \mathrm{kft}) d}{10 * 2770} \rightarrow \frac{I(\Omega / \mathrm{kft}) d}{2770} \mathrm{~V}\\\\$\% V D \rightarrow \frac{I(\Omega / k f t) d}{2770}$[/tex]
In conclusion, the expression for the voltage drop between inverter and PUC
[tex]V D \rightarrow \frac{I(\Omega / k f t) d}{2770}$[/tex]
CQ
An inverter has a balanced 3-phase, 277/480 V output and is installed a distance, d, ft from the point of utility connection. The DC/AC converter is shown below in the inverter. And the distance d is the physical separation between this DC/AC converter and the PCC.
Derive an expression for the voltage drop between inverter and PUC in terms of d using the basic equation %VD =100IR/V.
Read more about voltage drop
https://brainly.com/question/13094809
#SPJ1
What is the mode of operation of a ramp digital voltimeter
Answer:
The operating principle of a ramp type digital voltmeter is to measure the time that a linear ramp voltage takes to change from level of input voltage to zero voltage (or vice versa).
If your crew is the first to arrive on the scene of a major mci, what will be a major aspect of your scene size-up?
If your crew is the first to arrive on the scene of a major MCL, The major aspect of your scene size-up will be to Make a sweep to determine what needs must be met. Option D. This is further explained below.
What is the scene of an MCL?Generally, If your team is the first to arrive at the scene of a significant MCL, the most important part of your scene size-up will be to do a sweep to identify the requirements that need to be satisfied. Choose option D.
In conclusion, A medial collateral ligament (MCL) injury occurs when the ligament on the inside of the knee is stretched, partially torn, or completely ruptured. Most knee injuries are caused by an excessive amount of valgus stress on the knee, which is one of the most prevalent.
Read more about the scene of an MCL
https://brainly.com/question/13184254
#SPJ1
CQ
If your crew is the first to arrive on the scene of a major MCI, what will be a major aspect of your scene size-up?
A.
Make an initial scene report to the communications center.
B.
Control on-scene communication as help arrives.
C.
Prevent uncoordinated or undirected activity at the scene.
D.
Make a sweep to determine what needs must be met.
The advantage of using a reference line to position a building is that
Answer:
The reference line helps you achieve the precise connection of Walls for clean intersections.
Explanation:
Reference Lines allow you to place lines on the plot at specific locations to mark important values. You could use these to mark control limits or to indicate a trend line for a set of data.
Through Engineering, human achievement continues to advance. Write about your favorite example of engineering in action and what impresses you about it from an Engineering standpoint.
Hydroelectric power plants are outstanding engineering devices that allow people to obtain energy from renewable sources.
What is a hydroelectric power plant?A hydroelectric power plant is a center for the production of electricity based on hydropower energy systems.
Hydroelectric power plants exploit the energy of water masses (e.g., a stream) to produce clean energy for million of people around the world.
These plants have generators capable of converting mechanical energy into electricity by using simple turbines.
In conclusion, hydroelectric power plants are outstanding engineering devices that allow people to obtain energy from renewable sources.
Learn more about Hydroelectric power plants here:
https://brainly.com/question/8934285
#SPJ1
Which level of acceleration should you use when accelerating on a short highway entry ramp?
The higher level of acceleration should be used when accelerating on a short highway entry ramp.
Given data:
When accelerating on a short highway entry ramp, you should use a higher level of acceleration to safely merge with the traffic already on the highway. This is particularly important when the entry ramp is short, as you need to reach the speed of the highway traffic and find a suitable gap to merge into the flow.
Using a higher level of acceleration allows you to match the speed of the vehicles on the highway more quickly and efficiently, reducing the risk of causing disruptions or potential hazards. It's essential to accelerate smoothly and decisively to ensure a safe merge onto the highway. Always follow traffic rules and guidelines while merging onto highways to ensure the safety of yourself and others.
To learn more about acceleration, refer:
https://brainly.com/question/12550364
#SPJ12
a. Calculate the equivalent resistance of the circuit
Answer:
no any think photo.
Explanation:
_____require(s) driving at speeds that are reasonable and prudent for conditions.
Basic speed law requires individuals driving at speeds that are reasonable and prudent for conditions.
What is Speed?This is defined as the rate of change of the position of a body with respect to time and the unit is metre per second.
The basic speed law states that speeds which are reasonable and prudent should be adopted by drivers so as to avoid accidents and potential risks to other road users. Appropriate punishment are also meted out to defaulters in this type of scenario.
Read more about Speed laws here https://brainly.com/question/13211153
#SPJ1
The displacement of a particle which moves along the s-axis is given by; = (−2 + 3)−0.5 Where s is in meters and t is in seconds. Determine the time at which the acceleration is zero.
The time at which the acceleration is zero is given as 4.66 seconds
How to solve for the timeFirst we have to solve for the velocity. To do this, we would have to take the derivative.
[tex]s = e^-0.5t (3 t - 2)[/tex]
Then velocity =
[tex]ds/dt = e^-0.5t (4 - 1.5 t)[/tex]
The acceleration can be gotten by finding the second derivative
[tex]a = dv/dt = e^-0.5t (.75 t - 3.5)[/tex]
To find t at acceleration = 0
We have
[tex]0 = e^-0.5t (.75t - 3.5)[/tex]
This gives t to be
t = 4.66 sec
Complete questionThe displacement of a particle which moves along the s-axis isgiven by
s = (-2+3t)e^(-0.5t), where s is in meters and t is inseconds. Plot the displacement, velocity and acceleration versustime for the first 20 seconds of motion. Determine the time atwhich the acceleration is zero.
Read more on acceleration here:
https://brainly.com/question/605631
#SPJ1
If a dielectric material, such as teflon®, is placed between the plates of a parallel-plate capacitor without altering the structure of the capacitor, how is the capacitance affected?.
The capacitance is affected is that the capacitance increases because of the insertion of Teflon.
What is capacitance?A `is known to be a form of a device that is said to be used to save some amount of charges in any electrical circuit.
Note that the capacitor functions on the principle that the capacitance of a conductor is said to increases if an earthed conductor is taken close to it.
Hence, The capacitance is affected is that the capacitance increases because of the insertion of Teflon.
See full question below
A dielectric material, such as Teflon®, is placed between the plates of a parallel-plate capacitor without altering the structure of the capacitor. The charge on the capacitor is held fixed. How is the electric field between the plates of the capacitor affected?
The electric field is not altered, because the structure remains unchanged.
The electric field becomes zero after the insertion of the Teflon®.
The electric field decreases because of the insertion of the Teflon®.
The electric field becomes infinite because of the insertion of the Teflon®.
The electric field increases because of the insertion of the Teflon®.
Learn more about electric field from
https://brainly.com/question/14781269
#SPJ1
The lights on your vehicle must be turned on at any time, day or night, when persons and vehicles cannot be clearly seen for ___ feet.
Answer:
500 feetExplanation:
In order to stop or turn your vehicle around on the highway you must have 500 feet of clear road in both directions. 4. Headlights are required at any time you cannot see persons or vehicles for 500 feet, due to snow, dust, fog, etc. and from ½ after sunset to ½ before sunrise.Hope this helpsThe lights on your vehicle must be turned on at any time, day or night, when persons and vehicles cannot be clearly seen for 1000 feet.
What are vehicles?A vehicle is a piece of equipment, typically with wheels and an engine, used for land-based transportation of people or goods. Cars, buses, and trucks are examples of road vehicles. Farm vehicles include tractors.
Vehicle type refers to a group of power-driven vehicles that share all crucial aspects of their engines, cars, and OBD systems.
When a vehicle is 500 feet away, the driver must dim his headlights.
Avoid looking directly into the light when a car is coming at you; instead, slow down. At least 30 minutes before dusk, headlights must be activated. It is also important to keep in mind that a lower headlight beam improves the driver's ability to see in fog.
Thus, it should be 1000 feet distance.
For more details regarding vehicles, visit:
https://brainly.com/question/29491014
#SPJ2
A spark-ignition engine operates on an Otto cycle with a compression ratio of 9 and temperature limits of 30°C and 1000oC. The power output is 500 kW. Calculate the
a)thermal efficiency
b) mass flux of air
The thermal energy when the spark-ignition engine operates on an Otto cycle with a compression ratio of 9 and temperature limits of 30°C and 1000oC is 58%.
How to illustrate the information?From the information given, we are told that spark-ignition engine operates on an Otto cycle with a compression ratio of 9 and temperature limits of 30°C and 1000oC.
The thermal energy will be:
= 1 - 1/(1.4 - 1)
= 0.58
= 58%
Also, the mass flux of air will be illustrated below:
T2 = 729.70k
W = 224.60kj
Therefore, the mass flux will be:
= 500/224.60
= 2.226kg/s
In conclusion, the the mass flux will be 2.226kg/s.
Learn more about engine on:
brainly.com/question/25870707
#SPJ1
Which load balancing method is supported in equal cost multipath (ECMP) load balancing when SD-WAN is enabled
Volume load balancing method is supported in equal cost multipath (ECMP) load balancing when SD-WAN is enabled.
What is load balancing method?Load balancing means are regarded as a form of an algorithms or method that is used to rightly share an incoming server request or traffic in the midst or among servers that is from the server pool.
Note that Volume load balancing method is supported in equal cost multipath (ECMP) load balancing when SD-WAN is enabled as that is its role.
Learn more about Volume load balancing from
https://brainly.com/question/28021339
#SPJ1
Datums and benchmarks are used for ______
Answer:
Measuring elevations
Explanation:
hope this helps you ♡´･ᴗ･`♡
When passing another car, make sure you maintain at least a _______ safety cushion
based on the graph shown, for any given output level, the veritcal distance between the avc and the atc curves represents
A a result of the graph shown, for any given output level, the veritcal distance between the avc and the atc curves represents total fixed cost (TFC).
What is Vertical distance?This is known as vertical separation and it is said to be the distance that exist between two vertical positions.
Note that vertical coordinates are seen for expressing vertical position: depth, and others and as such,
See full question below
The vertical distance between the ATC and AVC curve represents
a) marginal cost (MC)
b) average fixed cost (AFC)
c) total fixed cost (TFC)
d) total cost (TC) - total variable cost (TVC)
Learn more about from
https://brainly.com/question/210650
#SPJ1
7.35 and 7.36 For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the maximum absolute values of the shear and bending moment.
Maximum absolute values of the shear = 28 KN
Maximum absolute values of bending moment = 5.7 KN.m
How to draw Shear Force and Bending Moment Diagram?A) We can see the beam loaded in the first image attached.
For the shear diagram, let us calculate the shear from point load to point load.
From A to C, summing vertical to zero gives; ∑fy = 0: -20 - V = 0
V = -20 KN
From C to D, summing vertical to zero gives; ∑fy = 0: -20 + 48 - V = 0
V = 28 KN
From D to E, summing vertical to zero gives; ∑fy = 0: -20 + 48 - 20 - V = 0
V = 8 KN
From E to B, summing vertical to zero gives; ∑fy = 0: -20 + 48 - 20 - 20 - V = 0
V = -12 KN
For the bending moment diagram, let us calculate the bending moment from point load to point load.
At point A, the bending moment would be zero. Thus, M_A = 0 KN.m
At point C, taking moment about point C and equating to zero gives;
M_C = 0. Thus; 20(0.225) + M = 0
M = -4.5 KN.m
At point D, taking moment about point D and equating to zero gives;
M_D = 0. Thus; 20(0.525) - 48(0.3) + M = 0
M = 3.9 KN.m
At point E, taking moment about point E and equating to zero gives;
M_D = 0. Thus; 20(0.75) - 48(0.525) + 20(0.225) + M = 0
M = 5.7 KN.m
At point B, taking moment about point E and equating to zero gives;
M_E = 0. Thus; 20(1.05) - 48(0.825) + 20(0.525) + (20 * 0.3) + M = 0
M = 2.1 KN.m
2) From the attached diagrams, we can deduce that;
Maximum absolute values of the shear = 28 KN
Maximum absolute values of bending moment = 5.7 KN.m
Read more about shear force & bending moment diagram at; https://brainly.com/question/14834487
#SPJ1
Which two events in britain indirectly influenced the american revolution?
enlightenment philosophers established which two of the following ideas?
Answer:
passage of the English will of right
Draw the schematics for the following two battery connections. Can you explain the value of the output voltage in the series connection
if two 1.5 ya alt batteries are connected to head to the tail the voltage is 3.0 volt it is the because the battery is insidious reduce a voltage equal to number of battery is multiplied by the voltage of individual
Continued and/or excessive heat and centrifugal force on turbine engine rotor blades is likely to cause?
Answer:
Continued and/or excessive heat and centrifugal force on turbine engine rotor blades is likely to cause creep.
Explanation:
Creep is a technical term for permanent elongation that happens over time. Heat will result in the rotor blades' material becoming less dense which will allow the material to stretch since the force is centrifugal.
A company is currently paying its employees $0.38 per mile to drive their own cars on company business. The company is considering supplying employees with cars, which would involve purchasing at $25,000 with an estimated three-year life, a net salvage value of $8,000, taxes and insurance at a cost of $900 per year, and operating and maintenance expenses of $0.22 per mile. If the interest rate is 10% and the company anticipates an employee’s annual travel to be 22,000 miles, what is the equivalent cost per mile (neglecting income taxes)?
The equivalent cost per mile is mathematically given as
Equivalent kilometer = 0.61
What is Distance?Distance is a measure of the distance between two places. Depending on context, the term "distance" might refer to a precise measurement or an approximation based on other factors. |AB| can be used to represent the distance between two points.
What is an Equivalent cost per mile?Generally, the equation for Equivalent annual cost is mathematically given as
EAC= $ 25,000 ( A/P, 10% , 3 years ) + $ 900 + $ 0.22 * 22,000 - $ 8000 ( A/F , 10% , 3 years)
Therefore
EAC= $ 25,000 * 0.402115 + $ 5740 - $ 8000 * 0.302115
EAC= $ 13,375.955
In conclusion, the Equivalent cost per kilometer
Equivalent kilometer [tex]=\frac{ 13,375.955}{22,000}[/tex]
Equivalent kilometer = 0.61
Read more about Equivalent kilometers
https://brainly.com/question/14332835
#SPJ1
An important difference between expressways and freeways is that expressways feature intersections, whereas freeways use: a) interchanges b) medians c) rumble strips d) green guide signs
An important difference between expressways and freeways is that expressways feature intersections, whereas freeways use a) interchanges.
Assignment: Explain any three
ways that research can facilitate
the work of building technicians.
The three ways that research can facilitate the work of building technicians is that:
They will know the timeframe to start and complete the buildingThey will know the type and right materials to use.It will help them in the area of budgeting of equipment, tools and building materials needed.What do building technicians do?Building technicians are known to be people who help with some tasks around construction projects and building works.
Note that building technician overseeing a scope of tasks such as monitoring build progress and as such The three ways that research can facilitate the work of building technicians is that:
They will know the timeframe to start and complete the buildingThey will know the type and right materials to use.It will help them in the area of budgeting of equipment, tools and building materials needed.Learn more about technicians from
https://brainly.com/question/1548867
#SPJ1
How are new slip rings attached to the rotor core during alternator rebuilding?
The new slip rings is been attached to the rotor core during alternator rebuilding by b. Soldered on.
What is the process of Soldering ?Soldering is the use of Solder which is a metal alloy consisting tin and lead and is the way of joining different types of metals together by melting solder.
This is been used on new slip rings to get it attached to the rotor core during alternator rebuilding .
Learn more about Soldering on:
https://brainly.com/question/25759088
#SPJ1
CHECK THE COMPLETE QUESTION BELOW:
How are new slip rings attached to the rotor core during alternator rebuilding?
a. Machine clamped
b. Soldered on
c. Crimped on
d. epoxy glue
When referring to private land use restrictions, fence height, additional structures, and architectural design are generally categorized under ______.
The fence height, additional structures, and architectural design are generally categorized under covenants.
What is the land use about?The primary private land-use control is known to be a form of a deed restrictions, that hinders what a person can do on the property as regards to the owner.
Note that in the case above, the fence height, additional structures, and architectural design are generally categorized under covenants.
Learn more about private land use from
https://brainly.com/question/626688
#SPJ1
A light weight vehicle traveling 50 mph can stop in approximately
a. 200 meters.
b. 5 blocks.
c. 200 feet.
d. 6 seconds.
A light weight vehicle traveling 50 mph can stop in approximately 200 feet.
How a car break works?
The break system of a car is composed by several items that are always working together to slow down and bring a vehicle to a complete stop. It also has the function of keeping the car stationary when it is parked. In general, this system has two manual activation modes: the lever and the pedal, with the exception of vehicles adapted for people with disabilities.
Most vehicles today use the disc brake system. Disc brakes work by using pads, which are held inside a hydraulic caliper, receiving pressure to brake. Such pads generate friction on a disc, which makes the vehicle stop permanently.
The drum brake is another type, being older and dependent on the famous linings to cause friction in the wheel and stop the vehicle. A hydraulic cylinder makes the plies move inside the drum, which is a hollow part fastened with screws and attached to the wheels. This type of brake is on the rear wheels, for the most common models.
See more about engineering at: brainly.com/question/19117846
#SPJ1