Answer:
100kg x 4 x 10 = 4000J
Explanation:
A power plant running at 31 % efficiency generates 270 MW of electric power. Part A At what rate (in MW) is heat energy exhausted to the river that cools the plant
The rate of heat energy exhausted to the river is 600.96 MW.
What is efficiency?The ratio of usable output to total input can be used to objectively measure efficiency. The efficiency of the device is defined as the ratio of energy converted to a useable form to the original amount of energy supplied.
Given parameters:
Efficiency of the power plant; η = 31 %
Output electric power; O = 270 MW.
We know that, Efficiency of the power plant;
η = (Output electric power/ input power)× 100%
⇒ input power = (Output electric power × 100)/η
⇒ input power = (270 × 100)/31 MW
= 870.96 MW.
So, the rate of heat energy exhausted to the river that cools the plant = Input power- output power
= (870.96 - 270) MW
= 600.96 MW.
Hence, heat energy exhausted to the river that cools the plant is 600.96 MW.
Learn more about efficiency here:
https://brainly.com/question/14502027
#SPJ1
At a distance of 1 cm from the source, the flux from the isotropic source is one hundred times brighter. Which source is brighter fifty centimeters away
Answer:
op
Explanation:
At a distance of 1 cm from the source, the flux from the isotropic source is one hundred times brighter. Which source is brighter fifty centimeters away
3. What is Newton's 1st Law?
A For every action there is an equal and opposite reaction
B. Acceleration depends on two variables, the mass of the object and the amount of
force
C. An object at rest will stay at rest, an object in motion will stay in motion, unless an
unbalanced force acts upon it.
O D. The amount of matter in an object
Answer:
A
Explanation:
for every action there is an equal and opposite reaction
Easiest way to Find fahrenhiet to celsius please i need necessary 20 for the fastest correct answer
Answer:
thx for the points
Explanation:
no need brainliest
A boat is headed north at a velocity of 8 km h-1. A strong wind is blowing whose pressure on the boat’s superstructure causes it to move sideways to the west at a velocity of 2 km h-1. There is also wave present that flows in a direction 30° south of east at a velocity of 5 km h-1. What is the velocity of the boat?
The velocity of the boat moving at the given conditions is 5.97 km/h at 67⁰.
The given parameters;
velocity of boat northwards, = 8 km/hvelocity of the boat westwards, = 2 km/hvelocity of the wind, = 5 km/h 30° south of eastThe resultant vertical velocity of the boat is calculated as;
[tex]v_y = 8 \ - \ 5 sin(30)\\\\v_y = 8 - 2.5\\\\v_y = 5.5 \ km/h[/tex]
The resultant horizontal velocity of the boat is calculated as;
[tex]v_x = -2 \ + 5cos(30)\\\\v_x = 2.33 \ km/h[/tex]
The resultant boat velocity is calculated as follows;
[tex]v = \sqrt{v_x^2 + v_y^2} \\\\v = \sqrt{2.33^2 + 5.5^2} \\\\v = 5.97 \ km/h[/tex]
The direction of the velocity;
[tex]\theta = tan^{-1} (\frac{v_y}{v_x} )\\\\\theta = tan^{-1}(\frac{5.5}{2.33} )\\\\\theta = 67 \ ^0[/tex]
Thus, the velocity of the boat moving at the given conditions is 5.97 km/h at 67⁰.
Learn more here:https://brainly.com/question/12982473
What is gravitation ?
Explanation:
1. Movement, or a tendency to move, toward a center of gravity, as in the falling of bodies to the earth.
2. Movement toward or attraction to something.
"a tentative gravitation toward the prices that we saw before the announcement"
A tow truck pulls a car 5.00 km along a horizontal roadway using a cable having a tension of 850 N. (a.) How much work does the cable do on the car if it pulls horizontally? If it pulls at 35.0° above the horizontal? (b.) How much work does the cable do on the tow truck in both cases of part (a)? (c.) How much work does gravity do on the car in part (a)?
I think 1980is the answer because you add???
Identify:
In each case the forces are constant and the displacement is along a straight line, so
[tex]$$W=F s \cos \phi \text {. }$$[/tex]
Set-Up:
In part (a), when the cable pulls horizontally [tex]$\phi=0^{\circ}$[/tex] and when it pulls [tex]$35.0^{\circ}$[/tex] above the horizontal [tex]$\phi=35.0^{\circ}$[/tex]. In part (b), if the cable pulls horizontally[tex]$\phi=180^{\circ}$[/tex]. If the cable pulls on the car [tex]$35.0^{\circ}$[/tex] above the horizontal it pulls on the truck at below the horizontal and [tex]$\phi=145.0^{\circ}$[/tex]. For the gravity force [tex]$\phi=90^{\circ}$[/tex], since the force is vertical and the displacement is horizontal.
Execute:
(a) When the cable is horizontal, [tex]$W=(850 \mathrm{~N})\left(5.00 \times 10^{3} \mathrm{~m}\right) \cos 0^{\circ}=4.25 \times 10^{6} \mathrm{~J}$[/tex].
When the cable is[tex]$35.0^{\circ}$[/tex] above the horizontal,[tex]$W=(850 \mathrm{~N})\left(5.00 \times 10^{3} \mathrm{~m}\right) \cos 35.0^{\circ}=3.48 \times 10^{6} \mathrm{~J}$[/tex].
(b)[tex]$\cos 180^{\circ}=-\cos 0^{\circ}$[/tex] and [tex]$\cos 145.0^{\circ}=-\cos 35.0^{\circ}$[/tex],
So the answers are [tex]$-4.26 \times 10^{6} \mathrm{~J}$[/tex] and [tex]$-3.48 \times 10^{6} \mathrm{~J}$[/tex].
(c) Since [tex]$\cos \phi=\cos 90^{\circ}=0, W=0$[/tex] in both cases.
Evaluate: If the car and truck are taken together as the system, the tension in the cable does no net wnetwork
Learn more about horizontal reffer to
https://brainly.com/question/4138300
#SPJ2
The tires of a car make 77 revolutions as the car reduces its speed uniformly from 95.0 km/h to 65.0 km/h. The tires have a diameter of 0.90 m.
If the car continues to decelerate at this rate, how far does it go? Find the total distance.
Answer:
Explanation:
95.0 km/hr = 26.39 m/s
65 km/hr = 18.06 m/s
Circumference of a tire is 0.9π m
77 revolutions is a distance of
77(0.9π) = 69.3π m
v² = u² + 2as
a = (v² - u²) / 2s
a = (18.06² - 26.39²) / (2(69.3π))
a = -0.85 m/s²
s = (v² - u²) / 2a
s = (0² - 26.39²) / 2(-0.85)
s = 409 m
A phone cord is 2.28 m long. The cord has a mass of 0.2 kg. A transverse wave pulse is produced by plucking one end of the taut cord. The pulse makes four trips down and back along the cord in 0.849 s. What is the tension in the cord?
The characteristics of the speed of the traveling waves allows to find the result for the tension in the string is:
T = 10 N
The speed of a wave on a string is given by the relationship.
v =[tex]\sqrt{\frac{T}{\mu } }[/tex]
Where v es the velocty, t is the tension ang μ is the lineal density.
They indicate that the length of the string is L = 2.28 m and the pulse makes 4 trips in a time of t = 0.849 s, since the speed of the pulse in the string is constant, we can use the uniform motion ratio, where the distance traveled e 4 L
v = [tex]\frac{d}{t}[/tex]
v = [tex]\frac{4 L}{t}[/tex]
v = [tex]\frac{4 \ 2.28 }{0.849}[/tex]
v = 10.7 m / s
Let's find the linear density of the string, which is the length of the mass divided by its mass.
μ = [tex]\frac{m}{L}[/tex]
[tex]\mu = \frac{0.2}{2.28}[/tex]
μ = 8.77 10⁻² kg / m
The tension is:
T = v² μ
Let's calculate
T = 10.7² 8.77 10⁻²
T = 1 0 N
In conclusion using the characteristics of the velocity of the traveling waves we can find the result for the tension in the string is:
T = 10 N
Learn more here: https://brainly.com/question/12545155
2) A ray of light in air is approaching the boundary with water at an
angle of 52 degrees. Determine the angle of refraction of the light
ray. (Refractive index of air = 1, water = 1.33)
=
Answer:
Explanation:
ASSUMING the 52° is the angle of incidence measured from the perpendicular to the surface
n₁sinθ₁ = n₂sinθ₂
1 sin52 = 1.33sinθ₂
θ₂ = arcsin(sin52 / 1.33)
θ₂ = 36°
as measured from the perpendicular to the surface
Please write a paragraph explaining the bible verse below in your own words.
Exodus 16:19-20
Answer:
Moses had told them to not keep the food till morning but some kept some anyways because they probably thought they were going to starve or not have food the next morning but what I think it means is that you have to trust in God that he will provide for you and so when the people kept the food cuz he thought they were probably going to start of the next day it got maggots
what is a non-economic benefit to international trade
Answer:
non economic benefits to international trade means not being too much profit not selling too much things /items in international trade
what is the ratio of the average distances that oxygen will diffuse in a given time in air and water
A car of mass 5000 kg was initially moving at 100 km/h and stops at a distance of 55 m. Find the
magnitude of the net force (in N) acting to stop the car.
Answer:
|F| = 35 kN
Explanation:
a = F/m
100 km/hr(1000 m/km / 3600 s/hr) = 27.8 m/s
v² = u² + 2as
a = (v² - u²) / 2s
F/m = (v² - u²) / 2s
F = m(v² - u²) / 2s
F = 5000(0² - 27.8²) / 2(55)
F = - 35,072.9517...
Two objects are being lifted by a machine. One object has a mass of 2 kg, and is lifted at a speed of 2
m/s. The other has a mass of 4 kg and is lifted at a rate of 3 m/s.
a. Which object has more kinetic energy while it is being lifted?
Answer:
Kinetic energy = (1/2) (mass) (speed²)
First object: (1/2) (2 kg) (2 m/s)² = 4 joules .
Second object: (1/2) (4 kg) (3 m/s)² = 18 joules .
The second object had more kinetic energy than the first one had.
Explanation:
Answer:
Kinetic energy = (1/2) (mass) (speed²)
First object: (1/2) (2 kg) (2 m/s)² = 4 joules .
Second object: (1/2) (4 kg) (3 m/s)² = 18 joules .
The second object had more kinetic energy than the first one had.
10. What is Newton's 3rd Law?
O A. For every action there is an equal and opposite reaction.
B. Acceleration depends on two variables, the mass of the object and the amount of
force.
C. An object at rest will stay at rest, an object in motion will stay in motion, unless an
unbalanced force acts upon it.
D. The amount of matter in an object.
7. What is Newton's 2nd Law? *
Answer:
A. For every action there is an equal and opposite reaction.
What happened when a lobster release a claw? a. The lobster attacks with the claw. b. The lobster let the claw go. C. The lobster bites off the claw. D. The lobster eats with the claw.
Answer:b
Explanation:
Answer:
The lobster let the claw go. so, B.
Explanation:
i hope this helps.
How much force must be applied to push a 1.35 kg book across the desk at constant speed if the coefficient of sliding friction is 0.30?
The magnitude of the force that must be applied to push the book across the desk is 3.97 N.
The given parameters;
mass, m = 1.35 kgcoefficient of friction, μ = 0.3The acceleration of the book across the desk is calculated as follows;
a = μg
where;
g is acceleration due to gravitya = 0.3 x 9.8
a = 2.94 m/s²
The magnitude of the force that must be applied is calculated as follows;
F = ma
F = 1.35 x 2.94
F = 3.97 N
Thus, the magnitude of the force that must be applied to push the book across the desk is 3.97 N.
Learn more about applied force here:https://brainly.com/question/2733221
Condyloid joints are, logically enough, created by joints at condyle bone markings.
True or False
Answer: False
Explanation:
It's received in elliptical cavities.
False. The statement is not entirely accurate. Condyloid joints are a type of synovial joint that allow movement in two planes, similar to an ellipsoid joint.
These joints are characterized by an oval-shaped projection of one bone fitting into an elliptical cavity of another bone. The term "condyle" does refer to a rounded projection or bump on a bone, but not all condyle bone markings create condyloid joints.
Condyloid joints are found in various parts of the body, such as the wrist (between the radius and carpal bones) and the knuckles (between the metacarpal bones and phalanges). They allow for movements such as flexion, extension, abduction, adduction, and circumduction.
It's important to note that the formation of a condyloid joint involves not only the presence of condyle bone markings but also the specific structural arrangement of the bones and the presence of articular cartilage, joint capsule, and synovial fluid. Therefore, while the term "condyle" is related to these joints, it does not accurately capture the complexity of their formation and function.
To learn more about Condyloid joints, here
https://brainly.com/question/30165924
#SPJ3
A body at higher temperature contains more heat? Is this true ?
Is carbon a source or a sink of energy? Why?
Carbon-Based Fuels Dominate Global Energy Use
Crude oil, coal, and natural gas supply about 85% of the energy used in the world. Fossil fuels are valuable as sources of energy because they contain hydrocarbons and other carbon-based materials.
The flow of ground water is
Answer:
In hydrogeology, groundwater flow is defined as the "part of streamflow that has infiltrated the ground, entered the phreatic zone, and has been (or is at a particular time) discharged into a stream channel or springs; and seepage water." It is governed by the groundwater flow equation.
Describe all the ways a bicyclist can accelerate
A 12.0 kg box resting on a horizontal, frictionless surface is attached to a 5.00 kg weight by a thin, light wire that passes over a frictionless pulley (Figure 1). The pulley has the shape of a uniform solid disk of mass 2.60 kg and diameter 0.500 m. A) After the system is released, find the tension in the horizontal segment of the wire. B) After the system is released, find the tension in the vertical segment of the wire. C) After the system is released, find the x-component of the acceleration of the box. D) After the system is released, find the x- and y-components of the force that the axle exerts on the pulley.
Answer:
Explanation:
Assuming x direction is horizontal any y direction is vertical
As the moment of inertia of the pulley is I = (½)mR²
The pulley mass will appear as ½ its actual mass in the system.
F = ma
5.00(9.81) = (5.00 + 2.60/2 + 12.0)a
a = 49.05 / 18.3
a = 2.6803278...
a = 2.68 m/s²
A) T = 12.0(2.68) = 32.16... = 32.2 N
B) T = 5.00(9.81 - 2.68) = 35.65 = 35.7 N
C) aₓ = 2.68 m/s²
D) Fx = 32.2 N
Fy = 35.7 + 2.60(9.81) = 61.2 N
A)The tension in the horizontal segment of the wire will be 32.2 N
B)The tension in the vertical segment of the wire will be 35.7 N
What is acceleration?Acceleration is defined as the rate of change of the velocity of the body. Its unit is m/sec².It is a vector quantity. It requires both magnitudes as well as direction to define.
The given data in the problem is;
m is the mass box resting on a horizontal =12.0 kg
the uniform solid disk of mass of 2.60 kg
d is the diameter = 0.500 m.
A)The tension in the horizontal segment of the wire will be 32.2 N
The acceleration is found as;
[tex]\rm F = ma \\\\ a= \frac{49.05}{18.3} \\\\ \rm a= 2.68 \ m/sec^2[/tex]
The tension in the horizontal segment of the wire is found as;
T=ma
T= 12.0 ×2.68
T=32.2 N
Hence the tension in the horizontal segment of the wire will be 32.2 N
B)The tension in the vertical segment of the wire will be 35.7 N
T=m(g-a )
T= 5.00 × (9.8-2.68)
T=35.7 N
Hence the tension in the vertical segment of the wire will be 35.7 N
C) the x-component of the acceleration of the box. will be 2.68 m/s².
aₓ = 2.68 m/s²
D)The x- and y-components of the force that the axle exerts on the pulley will be 32.2 and 61.2 N respectively.
Fx = 32.2 N
Fy = 35.7 + 2.60(9.81) = 61.2 N
Hence the x- and y-components of the force that the axle exerts on the pulley will be 32.2 and 61.2 N respectively.
To learn more about acceleration refer to the link;
https://brainly.com/question/969842
There is a uniform magnetic field of magnitude B, pervading all space, perpendicular to the plane of rod and rails. The rod is released from rest, and it is observed that it accelerates to the left. In what direction does the magnetic field point?
The right hand rule to find the direction of the magnetic field for a falling bar is:
The charge is positive the magnetic field is outgoing, horizontally and towards us. The charge of the bar is negative, the magnetic field is incoming, that is horizontal away from us.
The magnetic force is given by the vector product of the velocity and the magnetic field.
F = q v x B
Where the bolds indicate vectors, F is the force, q the charge on the particle, v the velocity and B the magnetic field.
In the vector product, the vectors are perpendicular, which is why the right-hand rule has been established, see attached:
The thumb points in the direction of speed. Fingers extended in the direction of the magnetic field. The palm is in the direction of the force if the charge is positive and in the opposite direction if the charge is negative.
They indicate that the bar is dropped, therefore its speed is vertical and downwards, it moves to the left therefore this is the direction of the force, we use the right hand rule, the magnetic field must be horizontal, we have two possibilities:
If the charge is positive the magnetic field is outgoing, horizontally and towards us. If the charge of the bar is negative, the magnetic field is incoming, that is, horizontal away from us
In conclusion using the right hand rule we can find the direction of the magnetic field for a falling bar is:
The charge of the bar is negative, the magnetic field is incoming, that is horizontal away from us.The charge is positive the magnetic field is outgoing, horizontally and towards us.
Learn more about the right hand rule here: brainly.com/question/12847190
You have a 25 W and a 100 W bulb at home. When you connect one or the other, which bulb carries the greater current
Answer:
100 w bulb has more current.
Explanation:
P=V^2/R.
when velocity is constant power is inversly proportional to resistence, so 25 W will have an hogher resistance tjan a 100 w bulb.
P=VI
when v is constant, power is directly proportional to I. hence, 100 w bulbs will carry more current.
When you connect one or the other, the bulb that's connected carries more current than the one that's not connected.
When you connect BOTH of them, the 100W bulb carries more current than the 25W one.
Two parallel plates, separated by 0.20 m, are connected to a 12-V battery. An electron released from rest at a location 0.10 m from the negative plate. When the electron arrives at a distance 0.050 m from the positive plate, what is the potential difference between the initial and final points
The potential difference between the initial and final point is 3.0 V.
The given parameters:
distance between the plates, d = 0.2 mvoltage across the plates, V = 12 Vposition of the electron from negative plate, x₁ = 0.1 mposition of the electron from the positive plate, x₂ = 0.0 5mThe potential difference between the initial and final point is calculated as follows;
[tex]E = \frac{V}{d} \\\\\frac{V_1}{d_1} = \frac{V_2}{d_2}[/tex]
where:
[tex]d_2[/tex] is the distance of the electron between the positive and negative plate
[tex]0.1 + d_2 + 0.05 = 0.2\\\\d_2 + 0.15 = 0.2\\\\d_2 = 0.2 - 0.15\\\\d_2 = 0.05 \ m[/tex]
[tex]V_2 = \frac{V_1d_2}{d_1} \\\\V_2 = \frac{12 \times 0.05}{0.2} \\\\V_2 = 3.0 \ V[/tex]
Thus, the potential difference between the initial and final point is 3.0 V.
Learn more here:https://brainly.com/question/1494836
An airplane accelerates from a speed of 33 m/s at the constant rate of 3.0 m/s2 over a distance of 500 m. What the final velocity?
Answer:
Explanation:
v² = u² + 2as
v² = 33² + 2(3.0)(500)
v² = 4089
v = 63.9452...
v = 64 m/s
A car is traveling at 8 m/s accelerates at 3.1 m/s^2 to reach a final top speed of 56 m/s. How much time will pass before the car reaches its top speed
Please find attached photograph for your answer.
Hope it helps.
Do comment if you have any query.
Paano ka makaka tulong sa upang maiwasan ang suliranin ukol sa climate change
Answer:
Climate Change
Ito ang pagbabago sa normal na panahon sa isang lugar. Maaaring abnormal na pagbabago sa ulan na nattanggap ng isang lugar sa isang taon o ang abnormal na pagbabago sa init ng panahon.
Paano masusulusyunan ito?
Tanggalin sa pagkakasaksak ang mga gadgets kapag puno na
Huwag pumutol ng mga puno
Iwasan ang pagsakay sa transportasyon kung malapit lang ang pupuntahan
Explanation:
pa brainliest