Answer:
In physics, the weber is the SI derived unit of magnetic flux. A flux density of one Wb/m2 (one weber per square metre) is one tesla.
Hope it helps !
Answer:
Weber unit of magnetic flux in the international system of units (SI), defined as the amount flux that, linking an electrical circuit of one turn (one loop of wire) , produces in it an electromotive force of one volt as the flux is reduced to zero as a uniform rate in one second .
it was named in honour of the 19th century German physicist Wilhelm Eduard Weber
What is net force?
A. The sum of all the forces acting on an object
B. The difference between the largest and smallest forces acting on
an object
C. The largest force acting on an object
D. The smallest force acting on an object
Answer:
A. The sum of all the forces acting on an object.
A rectangular block measures 4.1cm by 2.8cm by 2.1cm. calculate its volume given you answer to an appropriate number of significant figures?
Answer:
Volume = 24 cm^3
Explanation:
We recall that the volume of the box is calculated via the formula:
Volume = length * height * width
and that in a product, the number of significant figures for the result should coincide with the number of significant figures of the factor that has the least of them.
In this case, all measures have the same number of significant figures: two. so we calculate the product, and then limit the answer value to exactly two significant figures:
Volume = 4.1 cm * 2.8 cm * 2.1 cm = 24.108 cm^3, which must be rounded to two significant figures as: 24 cm^3
Answer:
Volume = 24.108cm³
Explanation:
Volume = length × breadth × height
Volume = 4.1 × 2.8 × 2.1
Volume = 24.108
before leaving earth, the mass if an astronaut is measured to be 60kg. the astronaut lands on the moon and measures the acceleration of gravity to be 1.6 m/s^2. what is the mass of the astronaut at moon?
Answer:
The answer is 2,475$+948= add you will get the answer rn
The weight we experience on a surface is the product of our mass and acceleration due to gravity on that surface. The mass of the astronaut in earth was 60 kg . Then his mass at moon will be 9.76 kg.
What is gravitational force ?The gravitational force is the force by which an object attracts other objects into its center of mass. Earth attracts every objects into its center. That why we are all standing on the ground.
The weight we experience on earth is due to the gravity. That is the product of mass and acceleration due to gravity of a planet is the weight on the planet.
The weight of astronaut in earth = 60 kg
acceleration due to gravity on earth = 9.8 m/s²
mass = 60/9.8 m/s² = 6.19 kg
Acceleration due gravity on moon = 1.6 m/s²
then weight on moon = 1.6 m/s² ×6.19 kg = 9.7 kg.
Therefore, the weight of the astronaut in moon will be 9.7 kg.
Find more on gravitational force:
https://brainly.com/question/24783651
#SPJ5
What are the factors affect the Electric forces between two charges and What is the relationship between each factor and the Electric force ?
Explanation:
If the two charges are point charges - i.e., they don't have a size - the force between these charges depends on the
• Magnitude if each charge, q1 and q2
• Sign of each charge (+ or -)
• Distance between the charges, r
This is essentially Coulomb’s Law:
FE = (kq1q2)/r2
For collections of charges, you need to find the electric field E, and then use this fields to find a force on a small test charge q in the field. The test charge is always small to help you map the electric field, but not disturb it.
Of these electromagnetic waves, which has the A Over a unit distance, wave A has three crests and two troughs. The wave begins and ends at the rest position. B Over a unit distance, wave B has two crests and one trough. The wave begins at the rest position and ends at the top of a crest. C Over a unit distance, wave C has four crests and four troughs. The wave begins and ends at the rest position. longest wavelength?
Answer:
Wave B has the longest wavelength
Explanation:
The wavelength of a wave is the distance between two consecutive points that are in phase.
The wavelength of a wave is also defined as the distance between successive crests or troughs along the z-axis.
A crest is the point of maximum upward displacement whereas a trough is a point of maximum downward displacement.
Comparing the three waves A, B and C over a unit distance.
Wave A:
Wave A has three crests and two troughs. The wave begins and ends at the rest position. There are 2½ successive points in phase in wave A
Therefore, the wavelength = 1/2.5 = 0.4
Wave B:
Over a unit distance, wave B has two crests and one trough. The wave begins at the rest position and ends at the top of a crest. There are 1¼ successive points in phase in wave B
Therefore, the wavelength = 1/1¼ = 0.8
Wave C:
Over a unit distance, wave C has four crests and four troughs. The wave begins and ends at the rest position.
There are 4 successive points in phase in wave B
Therefore, the wavelength = 1/4 = 0.25
Therefore, wave B has longest wavelength
Do YOU think aliens are real? HELP PLS
Which answer best displays Adam's use of the civic virtue "diversity"?
Diversity means something is benifical to an entire group.
Diversity means fair treatment of all people the
Answer:Yes
Explanation:yeah i think it could be possible because the universe is so far and wide its probably infinite and if we did i personally believe that we would be absolutely be annihilated by them because we would be so far behind technology wise we would have no use for the\
YOU FELL FOR IT FOOL THUNDER CROSS SPLIT ATTACK
Isaac Newton discovered the three laws of motion. Which example best illustrates Newton's third law of motion, which describes action and reaction forces?
O a rocket takes off from the ground
O a book slides forward on a seat when the car stops
O a heavier ball falls at the same speed as a lighter ball
O a vehicle rounds a curve and changes its acceleration
The third law of motion defined the action and reaction force that the heavy ball should be fall at the same kind of the speed.
What is third law of motion?It defined that at the time when the two bodies should be interacted so here the forces should be applied to one another that should be equivalent to the magnitude also the direction should be opposite.
Also, we can called as the action law and the reaction.
Therefore, we can conclude that the third option is correct.
Learn more about motion here: https://brainly.com/question/12742278
Wavelength is a measurement of ___________ , while period is a measurement of ___________ . *
Speed; time
Time; speed
Distance; time
Time; distance
Distance; speed
Speed; distance
distance ; time
Explanation:
wavelength is in metres [m]
period is in seconds [s]
Two locomotives approach each other on parallel track. Each has speed of 95 km/h with respect to the ground.If they are initially 8.5 km apart. How long will it take before they reach each other?
Answer:
It will take 2.68 minutes for them to reach each other.
Explanation:
We use the two following kinematic equations, making the final position the same (for the moment they meet each other):
locomotive 1 --> [tex]x_f=v*t[/tex]
locomotive 2 --> [tex]x_f=8.5\,-\,v*t[/tex]
we make the two xf equal, and solve for the time (t) using v = 95 km/h:
[tex]95*t=8.5-95*t\\2*95*t=8.5\\t=8.5/(190)\\t = 0.0447\,\,hours[/tex]
converting the hours into minutes by multiplying this value times 60;
t = 2.68 minutes
what type of friction present when you wrench on a car?
Answer:Rolling friction is friction that acts on objects when they are rolling over a surface. Rolling friction is much weaker than sliding friction or static friction. This explains why most forms of ground transportation use wheels, including bicycles, cars, 4-wheelers, roller skates, scooters, and skateboards.
Explanation:
True/False: The Earth's core is completely solid, and the only liquid portion of the Earth's layers is the crust.
Answer:
true i believe
Explanation:
Answer:
true
Explanation:
true because other guy said it lol
A chair is thrown upward from a balcony that's 96 ft in the air, at an initial velocity of 16 ft/s.
How many seconds does the chair take to reach its highest height?
Answer:
t = 6 s
Explanation:
Given that,
A chair is thrown upward from a balcony that's 96 ft in the air, d = 96 ft
The initial velocity of chair, u = 16 ft/s
We need to find how many seconds does the chair take to reach its highest height. Let the time is t.
[tex]t=\dfrac{d}{v}\\\\t=\dfrac{96\ ft}{16\ ft/s}\\\\=6\ s[/tex]
Hence, the chair take 6 seconds to reach its maximum height.
A circular wire loop lies inside a region of space containing a magnetic field. The direction of the magnetic field is out of the screen and parallel to the central axis of the loop. The magnitude of the magnetic field increases as a function of time. A circular loop oriented parallel to the plane of the screen lies inside a region containing magnetic field B. The field is directed out of the screen and is increasing. What is the direction of the induced current in the loop
Answer:
clockwise
Explanation:
According to the law given by Lenz, known as the Lenz law, it is said that a current induced in the circuit which is due to the change in the magnetic field and is so directed so as to oppose the change in the flux and to apply a force in the opposite direction if the force.
Here, as the magnetic field is directed out of the screen, the current flows in the direction which is clockwise in the loop and it opposes the increasing magnetic field.
The clockwise induced current will produce magnetic field in to the screen.
Sadie rolls a marble down a ramp. When the marble reaches the bottom of the ramp, it then rolls across the floor. After a few seconds, the marble slows down, then stops. What caused the marble to stop? *
A Friction between the marble and the floor.
B Air pressure pushing down on the marble.
C The force of gravity pulling the marble down.
D Magnetic attraction between Earth and the marble.
What are the factors that affect the size of an impact crater?
Answer:
The following factors could be responsible for size of an Impact Crater:
Geography of the region where it impacted.Size of the Impactor Velocity of the ImpactorHope it helps!<3
how is solar impulse is different than conventional airplane
Answer:
Solar Impulse is a Swiss long-range experimental solar-powered aircraft project and Conventional Aircraft are the atmosphere-only aircraft that have been around since the Wright Flyer's first takeoff. Though modern craft are much more advanced and capable than that early model, Conventional Aircraft have been superseded in modern times by the AeroSpace Fighter, which can operate in both atmosphere and space.
Explanation:
The light given off by an object based only on its temperature supports the
particle model of light. Which term applies to this light?
A. Blackbody radiation
B. Photoelectric effect
C. Ultraviolet
D. Constructive interference
SUBM
Answer:
A.Blackbody Radiation
Explanation:
Answer:
A. Blackbody radiation
Explanation:
12 seconds after starting from rest a frewly falling cantaloupe has a speed of
Answer:
The cantaloupe has a speed of 117.6 m/s
Explanation:
Free Fall Motion
It occurs when an object falls under the sole influence of gravity. Any object that is being acted upon solely by the force of gravity is said to be in a state of free fall. Free-falling objects do not face air resistance.
If an object is dropped from rest in a free-falling motion, it falls with a constant acceleration called the acceleration of gravity, which value is [tex]g = 9.8 m/s^2[/tex].
The final velocity of a free-falling object after a time t is given by:
vf=g.t
The cantaloupe has been dropped from rest. We are required to find the speed after t=12 seconds.
Calculate the final speed:
vf=9.8 * 12 = 117.6 m/s
The cantaloupe has a speed of 117.6 m/s
What is the magnitude of the Box's Acceleration?
The Box's Acceleration : g sin θ
Further explanationNewton's 2nd law explains that the acceleration produced by the resultant force on an object is proportional and in line with the resultant force and inversely proportional to the mass of the object
∑F = m. a
F = force, N
m = mass = kg
a = acceleration due to gravity, m / s²
We plot the forces acting on the block (picture attached) according to the y-axis and the x-axis.
Because the motion of the block is in the same direction as the x-axis, ignoring the friction force with the inclined plane, then
[tex]\tt \sum F_x=m.a\\\\W.sin\theta=m.a\\\\mgsin\theta=m.a\\\\a=gsin\thet\theta[/tex]
in which part of the circulatory system can the exchange of gases and nutrients take place?
Many curves have banked turns, which allow the cars to travel faster around the curves than if the road were flat. Acutally, cars could also make turns on these banked curves if there were no friction at all. Explain this statement using the free-body diagram shown in the figure.
Answer:
the normal force that is perpendicular to the surface has a component towards the center of the curve.
Explanation:
When curves with superelevation or inclination, the normal force that is perpendicular to the surface has a component towards the center of the curve. This component is what maintains the vehicle and gives it centripetal acceleration.
Consequently, the vehicle does not need the friction force since it does not have a tendency to slide and this is zero.
A thyristor (SCR) is a
Answer:
A thyristor (/θaɪˈrɪstər/) is a solid-state semiconductor device with four layers of alternating P- and N-type materials. It acts exclusively as a bistable switch, conducting when the gate receives a current trigger, and continuing to conduct until the voltage across the device is reversed biased, or until the voltage is removed (by some other means).
Explanation:
Correct me if im wrong
In the formulas for latent heat of fusion and latent heat of vaporization, what does Q represent?
Answer:
Q is the amount of energy released or absorbed during the change of phase of the substance (in kJ or in BTU), m is the mass of the substance (in kg or in lb), and. L is the specific latent heat for a particular substance (kJ kg−1 or in BTU lb−1), either Lf for fusion, or Lv for vaporization.
I hope this helps∪ω∪
Answer:
A
Explanation:
What’s the answer to this
Please help! What kind of energy is produce by filament light?
Answer:
electrical to thermal and light
(may wanna change the answers)
and the one before that should be electrical to electrical i think
Explanation:
The FitnessGram Pacer Test is a multistage aerobic capacity test that progressively gets more difficult as it continues. The 20 meter pacer test will begin in 30 seconds. Line up at the start. The running speed starts slowly, but gets faster each minute after you hear this signal. A single lap should be completed each time you hear this sound. Remember to run in a straight line, and run as long as possible.
Which example provides a complete scientific description of an object in motion?
(A) The hiker followed the north trail a distance of two kilometers in thirty minutes
(B) The tiger had to run at 50 kilometers per hour across the field to catch the zebra
(C) The hockey player sent the puck flying toward the north goal to score the winning point
(D) The vibration of the jackhammer broke through the south-facing rock in under 10 seconds
Answer:
C
Explanation:
it explains how an object that was in motion continued motion after the force
Briefly describe the Rutherford atomic model
Answer:
The Rutherford model was made by Ernest Rutherford, to describe a atom. That is a brief explanation
Explanation:
A piece of copper wire with thin insulation, 200 m long and 1.00 mm in diameter, is wound onto a plastic tube to form a long solenoid. This coil has a circular cross section and consists of tightly wound turns in one layer. If the current in the solenoid drops linearly from 1.60 A to zero in 0.120 seconds, an emf of 80.0 mV is induced in the coil. What is the length of the solenoid, measured along its axis
Answer:
N= 3
Explanation:
For this exercise we must use Faraday's law
E = - dФ / dt
Ф = B . A = B Acos θ
tje bold indicate vectors. As it indicates that the variation of the field is linear, we can approximate the derivatives
E = - A cos θ (B - B₀) / t
The angle enters the magnetic field and the normal to the area is zero
cos 0 = 1
A = π r²
In the length of the wire there are N turns each with a length L₀ = 2π r
L = N (2π r)
r = L / 2π N
we substitute
A = L² / (4π N²)
The magnetic field produced by a solenoid is
B = μ₀ N/L I
for which
B₀ = μ₀ N/L I
The final field is zero, because the current is zero
B = 0
We substitute
E = - (L² / 4π N²) (0 - μ₀ N/L I) / t
E = μ₀ L I / (4π N t)
N = μ₀ L I / (4π t E)
The electromotive force is E = 0.80 mV = 0.8 10⁻³ V
let's calculate
N = 4π 10⁻⁷ 200 1.60 / (4π 0.120 0.8 10⁻³)]
N = 320 10⁻⁷ / 9.6 10⁻⁶
N = 33.3 10⁻¹
N= 3
A 1500 kg car is moving on a flat, horizontal flat road. If the radius of the curve is 35 m and
the coefficient of static friction between tires and dry road, Ms = 0.5. Calculate the maximum
speed the car can have and still make the turn successfully
The net force on the car is the friction that keeps it on the road, which points toward the center of the circle of the curve. Then by Newton's second law, we have
• net vertical force:
∑ F = N - W = 0
• net horizontal force:
∑ F = Fs = m a
where
N = magnitude of normal force
W = car's weight
Fs = mag. of static friction
m = car's mass
a = v ²/R = mag. of the centripetal acceleration
v = car's speed
R = radius of curve
Now,
• compute the car's weight:
W = m g = (1500 kg) (9.8 m/s²) = 14,700 N
• solve for the mag. of the normal force:
N = 14,700 N
• solve for the mag. of the friction force, using the given friction coefficient:
Fs = 0.5 N = 7350 N
• solve for the (maximum) acceleration:
7350 N = (1500 kg) a → a = 4.9 m/s²
• solve for the (maximum) speed:
4.9 m/s² = v ²/ (35 m) → v ≈ 13 m/s
Explain how a fish is able to enjoy 180° field of view when in a pond.
Answer:
Time
An explanation of basic pond measurements that are vital to basic pond management practices.
Save For Later Print
Pond Measurements: Area, Volume and Residence Time - Articles UPDATED: OCTOBER 29, 2015
Pond Measurements: Area, Volume and Residence Time
The importance of getting an accurate estimation of your pond surface area cannot be overestimated. The majority of pond owners visually estimate their pond area, which usually results in an overestimate of the true pond surface area. Pond area and water volume should be calculated based on some simple measurements. The effort necessary to estimate pond surface area is directly related to your pond's shape and uniformity. The simplest method--using basic equations for common shapes--can be applied if your pond closely resembles a circle, square, rectangle, or trapezoid in shape.
Pond Shapes
Circular
pond shape can be estimated by measuring the distance around the pond shoreline in feet. Square the shoreline distance and divide by 547,390 to get the pond area in acres. For example, a pond that is 450 feet around the shoreline would have an area = (450 feet)2 / 547,390 or 0.37 acres.
Explanation:
i looked this up