Which of the following would be considered unsaturated when 40g of solute is dissolved at 40ºC?


​

a
CaCl2
b
KCl
c
NaCl

(40 points)

Answer:

the answer is C. decrease agitation

Answer:

≈ 177.7%

Explanation:

To calculate the percent yield of NO, we need to compare the actual yield (what was obtained in the experiment) to the theoretical yield (what should have been obtained if the reaction had gone to completion).

First, we need to determine the theoretical yield of NO. We can do this by using stoichiometry to convert the given mass of NH3 to the expected mass of NO, based on the balanced equation. The ratio of the coefficients in the balanced equation tells us that 4 moles of NH3 produce 4 moles of NO, so the mole ratio of NH3 to NO is 1:1. Therefore, the mass of NO that should be produced is:

12.0 g NO = (8.9 g NH3) × (1 mole NO / 4 moles NH3) × (30.01 g NO / 1 mole NO)

where we have used the molar mass of NO (30.01 g/mol) to convert from moles of NO to grams of NO. Evaluating this expression gives:

12.0 g NO = 6.748 g NO

So, the theoretical yield of NO is 6.748 g.

To calculate the percent yield, we use the following formula:

percent yield = (actual yield / theoretical yield) × 100%

Substituting the given values, we get:

percent yield = (12.0 g / 6.748 g) × 100% ≈ 177.7%

This result suggests that the actual yield is greater than the theoretical yield, which is not possible. The most likely explanation is that there was an error in the experiment, such as incomplete reaction, loss of product during handling, or inaccurate measurement of the masses. Therefore, we should check the experimental procedure and repeat the experiment to obtain a more reliable result.

Tetragonal crystalline structure is shared by several other metal oxides, including the mineral tin dioxide, often known as stannic oxide or cassiterite (SnO 2).

The tetragonal unit cell of SnO 2's rutile structure possesses P4 2 /mnm space-group symmetry and lattice constants of a = b = 4.7374 and c = 3.1864 [13].

When we look at this unit cell, we can tell that the titanium is the block. The lead is blue, which equals 123456 and P. B. 6. As a result, there is one titanium since there are six lead. P B six T. I., then.

therefore, The red is oxygen after that. We may also observe that we have 1234 Last 678 liters of oxygen. Thus, it should be 08. So, the formula for this unit cell is as follows. The number would be PB 6 Ki I-08.

Learn more about unit cell here:

https://brainly.com/question/13110055

#SPJ1

The properly represents the order of orbital filling based on the relative energy of the orbitals is:

1s, 2s, 2p, 3s, 3p, 4s, 3d, 4p.

Orbitals are the regions or regions in space around the atomic nucleus that have the highest probability of finding electrons. In the arrangement of the orbital diagram, an electron is symbolized by an arrow facing up which represents an electron with spin +½, or facing down which represents an electron with spin -½. To mark the distribution of orbitals within the atom, these arrows are placed on a horizontal line, in a circle, or generally in a box.

Orbital diagrams are used to facilitate the determination of the value of the quantum numbers, namely the magnetic quantum number and the spin quantum number.

Your question is incomplete but most probably your full question was:

Which of the following properly represents the order of orbital filling based on the relative energy of the orbitals?

Multiple Choice

1s 2s 3s 4s 2p 3p 4p 3p

1s 2s 2p 3s 3p 3d 4s 4p

1s 2s 2p 3s 3d 3p 4s 4p

1s 2s 2p 3s 3p 4s 3d 4p

Learn more about orbital at

https://brainly.com/question/18914648

#SPJ4

The mass of CaCO₃ can be obtained as follow:

Mole = mass / molar mass

1.23 = Mass of CaCO₃ / 100.09

Cross multiply

Mass of CaCO₃ = 1.23 × 100.09

Mass of CaCO₃ = 123.11 g

The mole of C₁₂H₂₂O₁₁ can be obtained as follow:

Mole = mass / molar mass

Mole of C₁₂H₂₂O₁₁ = 65.32 / 342.34

Mole of C₁₂H₂₂O₁₁ = 0.19 mole

The mole of Ba₃(PO₄)₂ can be obtained as follow:

Mole = mass / molar mass

Mole of Ba₃(PO₄)₂ = 146 / 601.93

Mole of Ba₃(PO₄)₂ = 0.24 mole

The mass of F₂ can be obtained as follow:

Mole = mass / molar mass

3.25 = Mass of F₂ / 100.09

Cross multiply

Mass of F₂ = 3.25 × 38

Mass of F₂ = 123.5 g

The mole of Mg(OH)₂ can be obtained as follow:

Mole = mass / molar mass

Mole of Mg(OH)₂ = 760 / 58.87

Mole of Mg(OH)₂ = 12.91 moles

The mass of Fe₂O₃ can be obtained as follow:

Mole = mass / molar mass

0.234 = Mass of Fe₂O₃ / 159.7

Cross multiply

Mass of Fe₂O₃ = 0.234 × 159.7

Mass of Fe₂O₃ = 37.37 g

Learn more about mass:

https://brainly.com/question/21940152

#SPJ1

The matching of likely structure of the ion responsible for the base peak at 105, 72, 198,200, 91 and 43 differently.

The explanation and matching structure of the ions are given below:

a) The likely structure of the ion responsible for the base peak at 105 is a benzene ring with a substituent containing a nitrogen atom, such as aniline or N-methylaniline.

b) The likely structure of the ion responsible for the base peak at 72 is a methyl group, possibly as a fragment of a larger molecule.

c) The doublet at 198 and 200 suggests the presence of an isotope, and the base peak at 91 suggests the presence of a nitrogen-containing functional group, so a likely structure for the ion is an N-oxide functional group, such as a pyridine N-oxide.

d) The likely structure of the ion responsible for the base peak at 91 is a nitrogen-containing functional group, such as an amine or pyridine ring, and the large peak at 43 is likely a fragment containing a single nitrogen atom, such as NH2 or CH3N.

You can learn more about likely structure of ion at

https://brainly.com/question/25690897

#SPJ4

52.057g/mole is the average atomic mass of chromium. The correct option is option C among all the given options.

Meaning of Average Atomic Mass: To be more specific, the average atomic mass is defined as "the sum of the atomic masses of any and all isotopes of a particular element, each calculated by respective natural abundance on Earth." This is a straightforward explanation of average atomic weight.

The mass of such an atom is measured by its atomic weight (ma or m). Although the kilogram (symbol: kg) is the SI unit of mass, atomic mass is frequently stated inside the non-SI unit Dalton (symbol: Da) - equivalently, united atomic mass unit (u).

average atomic mass = 50×4.3 + 52×83.8 + 53×9.5 + 54×2.4= 52.057g/mole

Therefore, 52.057g/mole is the average atomic mass of chromium. The correct option is option C.

To know more about average atomic mass, here:

https://brainly.com/question/13753702

#SPJ9

The vapor pressure of the substance at 29°C is 622.5 mm Hg.

Vapor pressure is the pressure exerted by a vapor in thermodynamic equilibrium with its condensed phases (solid or liquid) at a given temperature in a closed system. It is often used as a measure of a substance's ability to vaporize.

The Clausius-Clapeyron equation can be used to calculate the vapor pressure of a substance at a given temperature by using the boiling temperature (Tb) and vapor pressure (Pb) at the boiling point. The equation is given by:

ln(P2/P1) = (AHvap/R)(1/T1 - 1/T2)

where P2 and T2 are the vapor pressure and temperature of interest, P1 and T1 are the vapor pressure and temperature at the boiling point, AHvap is the enthalpy of vaporization, and R is the universal gas constant.

For this problem, we are given T1 = 76°C, P1 = 714.6 mm Hg, AHvap = 38.7 kJ/mol, and R = 8.31 J/K mol. We want to calculate the vapor pressure at T2 = 29°C.

Using the equation above, we can calculate the vapor pressure at T2 as follows:

ln(P2/714.6) = (38.7 kJ/mol)(1/298.15 K - 1/303.15 K)

ln(P2/714.6) = (38.7 kJ/mol)(-0.0033 K-1)

ln(P2/714.6) = -0.128

P2 = e-0.128 x 714.6 = 622.5 mm Hg

To learn more about vapor pressure

https://brainly.com/question/4463307

#SPJ1

The compound to be purified must be soluble in the hot solvent and insoluble in the cold solvent. This is because during recrystallization, the compound is dissolved in the hot solvent to remove impurities, and then cooled to allow the compound to crystallize out of solution. If the compound is insoluble in the cold solvent, it will form pure crystals while impurities remain in solution. So the correct option is D.

Choosing the right solvent for recrystallization is crucial to ensure that the process is effective in purifying the compound. The solvent must be able to dissolve the compound at high temperatures to remove impurities, but then allow the compound to crystallize out of solution as the solvent cools.

By selecting a solvent in which the compound is soluble at high temperatures but insoluble at low temperatures, pure crystals of the compound can be obtained.

The complete question is given below

"

Which statement below best describes the reasoning behind choosing the most

suitable solvent to purify a sold by recrystalization ? Clearly choose one answer.

a) The compound to be purified must be soluble in both the hot solvent and the

cold solvent.

b) The compound to be purified must be insoluble in both the hot solvent and

the cold solvent.

c) The compound to be purified must be insoluble in the hot solvent and

soluble in the cold solvent.

d) The compound to be purified must be soluble in the hot solvent and

insoluble in the cold solvent.

"

You can learn more about recrystallization at

https://brainly.com/question/16835395

#SPJ4

The limiting reactant depends on the relative amounts of Al and O2 and can be determined by converting the amounts to the same unit and comparing them to the stoichiometric ratio in the balanced equation.

This question should be provided as:

For the reaction shown, find the limiting reactant for each of the following initial amounts of reactants.

In which is Al limiting and which is O2 limiting?

Learn more about limiting reactant brainly.com/question/14222359

#SPJ4

Most of the starch is broken down into glucose molecules, which are then absorbed by the cells of the small intestine and transported to the liver by the portal vein. In the small intestine, starch is hydrolyzed by enzymes, such as amylase, into its constituent glucose molecules.

Glucose is then transported across the intestinal wall and into the bloodstream by specialized transport proteins. From there, glucose is carried to the liver through the portal vein, where it can be stored, metabolized, or released into the bloodstream as needed to fuel other tissues. The breakdown of starch and subsequent transport of glucose are essential processes for providing energy to the body's cells and maintaining normal physiological functions.

Find out more about glucose molecules.

brainly.com/question/29240192

#SPJ4

According to the concept of Avogadro's number, there are 0.60×10²³  number of particles in 5.5 g of manganese.

Avogadro's number is defined as a proportionality factor which relates number of constituent particles with the amount of substance which is present in the sample.

It has a SI unit of reciprocal mole whose numeric value is expressed in reciprocal mole which is a dimensionless number and is called as Avogadro's constant.It relates the volume of a substance with it's average volume occupied by one of it's particles .

It is calculated as, 5.5/ 54.93×6.023×10²³=0.60×10²³ particles.

Learn more about Avogadro's number,here:

https://brainly.com/question/24175158

#SPJ9

The correct wedge and dash conformation for the following Newman projection is:  IV

The 3D structure of organic molecules is depicted using the wedge and dash conformation. It is frequently used in organic chemistry to display how substituents are oriented around chiral centers. The atoms in this conformation are dots, and the bonds in the molecule are represented by lines. Dashes and wedges depict bonds entering and exiting the paper's or screen's plane, respectively. The atoms' three-dimensional configuration can then be seen by rotating the molecule and looking at the direction of the bonds. Dashes denote the substituent is down and below the ring, whereas wedges denote the substituent is up and above the rings. Predicting the stereochemistry of chemical processes is made easier with the use of this notation.

To know more about wedge and dash conformation, check out:

https://brainly.com/question/20436961

#SPJ1

NaCl, KOH, C5H5, C6H24, KNO3, Na2SO4, CH2CH2OH are highly soluble in water and CHCl3, CH2OH, CCl4, CH2Cl2, CH3COOH, and CH3(CH2)5OH are either slightly soluble or insoluble in water.

The solubility of a compound in water refers to the ability of that compound to dissolve in water. Compounds that are highly soluble in water can easily dissolve in water, while those that are slightly soluble or insoluble cannot dissolve or dissolve only to a limited extent.

The solubility of a compound in water depends on several factors, including the chemical structure of the compound, the temperature and pressure of the solvent, and the presence of other solutes in the solvent.

Some common examples of highly soluble compounds in water include ionic compounds such as sodium chloride and potassium hydroxide, while nonpolar compounds such as chloroform and carbon tetrachloride are generally insoluble in water.

To know more about soluble here

https://brainly.com/question/24285799

#SPJ4

When you are sweating or shivering, you are exhibiting your limits of tolerance.

The human body can only withstand certain amounts of environmental stress. A key element in defining the body's tolerance limitations is temperature. Only a small range of temperatures is tolerable for the human body, and both hypothermia and hyperthermia can be fatal. Air pressure and humidity both have an impact on how well the body can withstand the environment. Altitude sickness and dehydration are both caused by low air pressure and high humidity, respectively. The body's capacity to endure the environment can also be impacted by pollution and chemical exposure. While exposure to radiation can result in cancer and genetic damage, noise pollution can also induce stress and hearing loss. Overall, a complex interplay of many environmental influences affects the human body's tolerance thresholds.

To know more about the limits of tolerance, check out:

https://brainly.com/question/26145317

#SPJ1

To draw an alternative Lewis structure, we need to move electrons to form a double or triple bond between the nitrogen atom and another atom in the molecule. We can also move electrons to form a lone pair on another atom in the molecule. The goal is to achieve a more stable structure with formal charges as close to zero as possible.

For example, consider the incomplete Lewis structure:

H

|

N

One possible resonance structure is:

H

|

N=H

In this structure, we have formed a double bond between the nitrogen atom and one of the hydrogen atoms. We have also placed a lone pair of electrons on the other hydrogen atom.

The formal charge on the nitrogen atom in this structure is:

Valence electrons in nitrogen = 5

Non-bonding electrons = 2

Number of bonds = 1

Formal charge = Valence electrons - Non-bonding electrons - 1/2(Number of bonds) = 5 - 2 - 1/2(1) = 2

Therefore, the formal charge on the nitrogen atom in this structure is +2.

Note that this is just one possible resonance structure. There may be other valid resonance structures that can be drawn, and the actual distribution of electrons in the molecule is a combination of all possible resonance structures.

To know more about Lewis structure click here:

brainly.com/question/4144781

#SPJ4

The power supply connector that is designed to provide power to a new hard drive in a desktop computer is the SATA power connector.

What is Hard Drive?

A hard drive, also known as a hard disk drive (HDD), is a type of data storage device that uses magnetic storage to store and retrieve digital information on a computer.

Hard drives consist of one or more rigid, rotating platters coated with a magnetic material, and a read/write head that moves over the platters to read and write data. The platters are spun at high speeds by a motor, while the read/write head floats just above the surface of the platters, using magnetic fields to read and write data.

SATA (Serial Advanced Technology Attachment) power connectors are used to provide power to SATA hard drives, as well as to other SATA devices such as optical drives and solid-state drives (SSDs). The SATA power connector is a small, rectangular, 15-pin connector that is typically located on the power supply cable coming from the power supply unit (PSU) in a desktop computer.

If your new hard drive requires power from the power supply unit, you will need to connect a SATA power connector to the drive's power port, which is usually located on the back of the drive. Some older hard drives may use a different type of power connector, such as the 4-pin Molex connector, but SATA is the most common type of power connector used for modern hard drives.

Learn more about Hard Drive from given link

https://brainly.com/question/26382243

#SPJ4

Answer:  To date, approximately 1,200 dinosaur skeletons have been discovered.

Scientists can only guesstimate the other parts of the bodies of dinosaurs because a lot of times, partial skeletons have been found. Or even, when a full skeleton has been found, the skin and organs and everything else are gone. This leaves the scientists to make educated guesses about how they stood, what they looked like and everything else in between based on the skeletons they've found.

1 mole of C are formed upon complete reaction of 2 mol of B according to the generic chemical reaction.

In the International System of Units, the mole (sign mol) is the unit of material quantity (SI). The amount of material is a measurement that indicates how many elementary constituents of a certain substance are present inside of an object or sample.

The mole has been defined as having 6.022×10²³ basic entities. An elementary entity can be an atom, chemical molecule, an ion, and ion pair, or perhaps a subatomic particle like an electron, depending on the substance.

A + 2B → C

moles of B = 2

the mole ratio between C and B is 1:2

moles of C= 1 mole

Therefore, 1 mole of C are formed upon complete reaction of 2 mol of B according to the generic chemical reaction.

To learn more about moles, here:

https://brainly.com/question/15209553

#SPJ6

The statement that is accurately describes the changes in the sample of copper when it is warmed from the room temperature to 95° Celsius is the correct option is c. The sample will expand.

The density is expressed as follows :

The Density = mass / volume

The density is define as the mass of the sample per unit volume. It is clear from the above equation that the density is directly proportional to the mass and the volume is inversely proportional to the density. Therefore the sample will expand if the density of the sample decreases as the temperature increases.

To learn more about density here

https://brainly.com/question/29775886

#SPJ4

This question is incomplete, the complete question is :

The density of copper decreases as temperature increases. Which statement accurately describes the changes in a sample of copper when it is warmed from room temperature to 95° Celsius?

a. The sample will become lighter.

b. The sample will become heavier.

c. The sample will expand.

d. The sample will contract.

Answer:

Many moles are formed

Explanation:

The number of moles in 5.00 × 10²³ formula units of BaBr₂ is approximately 0.83 moles, calculated by dividing the given number of formula units by Avogadro's number (6.022 × 10²³).

To determine the number of moles in 5.00 × 10²³ formula units of BaBr₂, you have to know the Avogadro's number, which is 6.022 × 10²³ formula units per mole.

Therefore, using Avogadro's number, you divide the given number of formula units by this value. So, the calculation is as follows: 5.00 × 10²³ formula units / 6.022 × 10²³ formula units per mole = 0.83 moles of BaBr₂.

So, there are approximately 0.83 moles in 5.00 × 10²³ formula units of BaBr₂.

https://brainly.com/question/34302357

#SPJ2

The false statement is, "Every methane molecule that reacts produces two water molecules." Option a is correct choice.

The balanced equation for the combustion of methane is CH₄ + 2O₂ → CO₂ + 2H₂O. This means that for every molecule of methane that reacts, only two molecules of water are produced, not two molecules of water for every methane molecule. Therefore, the statement that "every methane molecule that reacts produces two water molecules" is false.

Not every methane molecule that reacts produces two water molecules. Rather, for every methane molecule that reacts, two water molecules are produced. So the correct statement would be: For every molecule of CH₄ that reacts, two molecules of H₂O are produced.

To know more about the methane, here

brainly.com/question/2127750

#SPJ4

--The complete question is, Which one of the following statements about the following reaction is false? CH₄ + 2O₂ → CO₂ + 2H₂O.

a. Every methane molecule that reacts produces two water molecules.

b. If 32.0 g of oxygen reacts with excess methane, the maximum amount of carbon dioxide produced will be 22.0 g.

c. If 11.2 liters of methane react with an excess of oxygen, the volume of carbon dioxide produced at STP is (44/16)(11.2) liters.

d. If 16.0 g of methane react with 64.0 g of oxygen, the combined masses of the products will be 80.0 g.

e. If 22.4 liters of methane at STP react with 64.0 g of oxygen, 22.4 liters of carbon dioxide at STP can be produced.--

Answer:

ants release a chemical called formic acid onto your skin when they bite

a) 0.158 M is the concentration of the weak base.

b) 5.01 x [tex]10^{-3}[/tex] is the Kb of the weak base.

a) To determine the concentration of the weak base, we can use the equation:

moles of HCl = moles of weak base

We can calculate the moles of HCl from the volume and concentration:

moles of HCl

= 0.122 M x 0.03242 L

= 0.00395 mol

At the equivalence point, the moles of HCl will be equal to the moles of the weak base. Therefore, we can use this information to find the moles of the weak base:

moles of weak base = 0.00395 mol

Now we can use the volume and moles of the weak base to calculate its concentration:

The concentration of weak base = moles of weak base/volume of the weak base

The concentration of weak base = 0.00395 mol / 0.02500 L

The concentration of weak base = 0.158 M

Therefore, the concentration of the weak base is 0.158 M.

b) We have added half the quantity of HCl required to achieve the equivalence point at the half-equivalence point. We may thus conclude that half of the weak base has been neutralized while the other half is still in its fundamental state. This indicates that the weak base and its conjugate acid are present in equal proportions.

[weak base] = [conjugate acid]

We can use the expression for the ionization constant (Kb) to relate the concentrations of the weak base and its conjugate acid:

Kb = [conjugate acid] x [OH-] / [weak base]

Since the solution is at half-equivalence, the concentration of the weak base and its conjugate acid are both equal to 0.079 M (half of the initial concentration of the weak base). We can use this information and the given pH to calculate the concentration of hydroxide ions ([OH-]):

pH = 11.58 = 14 - pOH

pOH = 2.42

[OH-] = [tex]10^{-pOH}[/tex]

[OH-] = 5.01 x [tex]10^{-3}[/tex] M

Now we can use the expression for Kb to calculate its value:

Kb = [conjugate acid] x [OH-] / [weak base]

Kb = (0.079 M) x (5.01 x 10^(-3) M) / (0.079 M)

Kb = 5.01 x 10^(-3)

Therefore, the Kb of the weak base is 5.01 x [tex]10^{-3}[/tex].

For similar question on moles of HCl,

https://brainly.com/question/28623917

#SPJ4

To calculate the initial volume of oxygen gas burned in the reaction, we need to use the stoichiometry of the reaction, which relates the amounts of reactants and products based on their balanced chemical equation.

To find the initial volume of oxygen gas burned in the reaction, we need to use stoichiometry to relate the amounts of reactants and products. The balanced chemical equation for the combustion of hydrogen gas and oxygen gas to form water tells us that for every 1 mole of O2 consumed, 2 moles of H2O are produced.

We can use this ratio to convert the mass of water produced to the number of moles of O2 consumed. Finally, we can use the ideal gas law to calculate the initial volume of O2 consumed. Using STP of 0°C and 1 atm, we find that the initial volume of O2 burned in the reaction was about 24.3 liters.

You can learn more about mass of water at

https://brainly.com/question/26173436

#SPJ4

Answer:

sulfur. 14.

Explanation:

ccbhh Ivonne

Answer:

sulfur. 14.

ccbhh Ivonne

Explanation:

Due to its simplicity of use and high-throughput operations, liquid chromatography-mass spectrometry (LC-MS) is a widely used technique for determining peptide sequences.

To learn more about LC-MS, refer to:

https://brainly.com/question/16105508

#SPJ4

The order is d, a e c 4 h, 2 heat is absorbed, heat is a part, 3 dipole force And dispersion force.

H2CO is a polar molecule and will have both dipole-dipole forces and London dispersion forces while CH3CH3 is a non-polar molecule and will Only have London dispersions forces.

The intermolecular forces present for the molecules given are the London Dispersion forces and the dipole-dipole forces. The London Dispersion Forces exist for all molecules. Therefore, it will exist between H2O H 2 O And CH3CN C H 3 C N .

To learn more about dipole force & dispersion force

https://brainly.com/question/14958417

#SPJ4

Benzoquinone is created when the hydroquinone reacts with the hydrogen peroxide that is breaking down (C6H4O2). The oxygen and hydrogen reaction causes

To learn more about benzoquinone, refer to:

https://brainly.com/question/15727318

#SPJ4