Answer: answer is c rest of explanation is in the comments
In an inelastic collision:
I. only momentum is conserved
II. only kinetic energy is conserved
III. momentum and kinetic energy are both conserved.
IV. neither momentum nor kinetic energy are conserved.
Hi there!
I. Only momentum is conserved.
An inelastic collision means that there is a LOSS in the KINETIC ENERGY of the system.
However, momentum is ALWAYS conserved for every type of collision unless there is an external force acting on the system.
The instant before a batter hits a 0.14-kilogram baseball, the velocity of the ball is 45 meters per second west. The instant after the batter hits the ball, the ball's velocity is 35 meters per second east. The bat and ball are in contact for 1.0 x 10-2 second.
1. find the magnitude and direction of the average acceleration of the baseball while it is in contact with the bat.
2. calculate the magnitude of the average force the Bat exerts on the ball while they are in contact.
(1) The magnitude and direction of the average acceleration of the baseball while it is in contact with the bat is 8,000 m/s² east.
(2) The magnitude of the average force the Bat exerts on the ball while they are in contact is 1,120 N.
The given parameters:
Mass of the baseball, m = 0.14 kgInitial velocity of the baseball, u = 45 m/s west (negative direction)Final velocity of the baseball, v = 35 m/s east (positive direction)Time of contact, t = 0.01 sThe magnitude and direction of the average acceleration of the baseball while it is in contact with the bat is calculated as follows:
[tex]a = \frac{v- u}{t} \\\\a = \frac{35 - (-45)}{0.01} \\\\a = \frac{80}{0.01} \\\\a = 8,000 \ m/s^2[/tex]
The magnitude of the average force the Bat exerts on the ball while they are in contact is calculated as follows;
[tex]F = ma\\\\F = 0.14 \times 8,000\\\\F = 1,120 \ N[/tex]
Learn more about average force here: https://brainly.com/question/16200276
a 10 mh inductor is connected in series with a 10 ohm resistor, a switch and a 6 v battery. what is the time constant of the circuit
Answer:
The inductive time constant is just T = L / R
T = 10E-3 henry/ 10 ohm = 10E-2 sec = .1 sec
(.01 / 10 = .1)
A wave has frequency of 5 Hz and a speed of 25 m/s. What is the wavelength of the wave?
I need the Formula,Known,Substitute & Solve Answer with Units
Answer:
This is the answer that I got.
Explanation:
Just check over it once.
Grass, trees, shrubs, worms, birds, and deer that live in a certain area is known as what?
Answer:they live in grass land also called forests hope the answer helps
Explanation:
Calculate the resistance of a 1km length, 1mm diameter wire made from:
a) constantan (\rho = 4.9 × 10-7 Ωm)
b) copper (\rho = 1.7 × 10-8 Ωm)
c) State which material is better suited for being used to make resistors, and justify your answer.
d) With 1 amp of current flowing through each of the wires how much energy is converted to heat?
e) What potential difference would be needed to force a current of 1 amp through that length of each type of wire?
From the values of resistivity, the resistance of copper wire is 22 Ω.
Let us recall that;
R = ρl/A
ρ = resistivity
l = length of the wire
A = cross sectional area of the wire
For constantan;
R = 4.9 × 10^-7 × 1 × 10^3/[3.14 × ((1 × 10^-3)/2)^2]
R = 620 Ω
For copper;
R = 1.7 × 10-8 × 1 × 10^3/[3.14 × ((1 × 10^-3)/2)^2]
R = 22 Ω
The material that is best suitable to make resistors is constantan wire.
For constantan, the energy converted to heat is;
I^2 R = (1)^2 × 620 Ω = 620 W
For copper, the energy converted to heat is;
I^2R = (1)^2 × 22 Ω = 22Ω
The potential difference of constantan = IR = 1 × 620 Ω = 620 V
The potential difference of copper = = IR = 1 × 22Ω = 22 V
Learn more about resistivity:https://brainly.com/question/8106379
Plz help!
A person walks the path shown
below. The total trip consists of
four straight-line paths. At the end of the walk, what is the person's
resultant displacement measured from the starting point?
The analytical method for the sum of vectors allows to find the result for the sum of the vectors is:
The resulting vector has a modulus of R = 239.99 m and an angle of θ= 212.8º
The displacement is a vector quantity, therefore vector algebra must be used to perform the addition of vectors, in general there are two methods:
Graphic. In this case, the origin of a vector is placed at the tip of the previous one and the resulting vector goes from the origin of the first vector to the tip of the last, this method is not very precise. Analytical. In this method the vectors are decomposed into a coordinate system, the sum of the components is performed and the resulting vector is built, this method is very expensive.
Indicate in the graph a Cartesian coordinate system, let alone the West - East axis coincide with the x axis. Let's use trigonometry to decompose the vectors.
Vector A.
Aₓ = 100.0 m
Vector B.
B_y = -300.0 m
The negative sign indicates that it goes in the negative direction of the y-axis
Vector C.
We use trigonometry.
The angle measured from the positive side of the x-axis counterclockwise is
θ = 180 + 30 = 210
sin 210 = [tex]\frac{C_y}{C}[/tex]
cos 210 = [tex]\frac{C_x}{C}[/tex]
C_y = C sin 210
Cₓ = C cos 210
C_y = 150.0 sin 210 = -75.0 m
Cₓ = 150.0 cos 210 = -129.9 m
Vector D.
The angle from the positive side of the x-axis counterclockwise.
θ = 180-60 = 120º
sin 120 = [tex]\frac{D_y}{D}[/tex]
cos 120 = [tex]\frac{D_x}{D}[/tex]
D_y = D sin 120
Dₓ = D cos 120
D_y = 200.0 sin 120 = 173.2 m
Dₓ = 200.0 cos 120 = -100.0 m
we add the component with algebraic sum.
x = Aₓ + Cₓ + Dₓ
y = B_y + C_y + D_y
x = 100 - 129.9 -100 = -129.9 m
y = -300 - 75.0 + 173.2 = -201.8 m
We construct the resulting vector.
We use the Pythagorean theorem for the Modulus.
[tex]R+ \sqrt{x^2 +y^2}[/tex]
R = [tex]\sqrt{129.9^2 + 201.8^2 }[/tex]
R = 239.99 m
We use trigonometry for the angle.
tan θ = [tex]\frac{y}{x}[/tex]
θ = [tex]tan^{-1} \frac{y}{x}[/tex]
θ = [tex]tan^{-1} \frac{201.8}{129.9}[/tex]tan-1 (201.8 / 129.9)
θ = 57.2º
Since the two coordinates are negative, this angle is in the third quadrant; to measure it from the positive side of the x-axis.
θ = 270 - θ'
θ = 270 - 57.2
θ = 212.8º
In conclusion using the analytical method for the sum of vectors we can find the result for the sum of the vectors is:
The resulting vector has a modulus of R = 239.99 m and an angle of θ= 212.8º
Learn more about vector addition here: brainly.com/question/24855749
Construct an explanation for the fact that we don’t see the same amount of energy coming out at the end of these transformations as we did at the beginning. *
Answer:
When energy is transformed from one form to another, or moved from one place to another, or from one system to another there is energy loss.
Explanation:
Hope this helps! :)
why is acceleration not constant near the speed of light
Answer:
because when an object approaches the speed of light, it's mass starts to increase exponentially, and would be infinite at the speed of light. It would therefore require MORE than an infinite amount of energy to accelerate even a single electron to the speed of light
i. la protagonista ama a su gata. escribimos, en nuestros cuadernos , las razones por las que pensamos que las personas aman de manera exagerada a sus mascotas. Proponemos un antídoto para la soledad. Lo escribrimos
Las mascotas son una buena fuente de compañía y socias en la soledad.
La protagonista ama a su gato porque las mascotas son una buena fuente de compañía y es un antídoto para la soledad. Estas mascotas como perros, gatos, loros, etc. dan placer y felicidad a las personas.
La gente tiene mascotas para pasar tiempo con ellas y jugar con ellas para refrescar sus mentes. Tener mascotas es una actividad maravillosa que hace que nuestra mente esté relajada y llena de felicidad, por lo que podemos concluir que las mascotas son una buena fuente de compañía y compañera en la soledad.
Learn more about pest here: https://brainly.com/question/989131
Learn more: https://brainly.com/question/25948065
Suppose you take a piece of hard wax from an unlit candle. After you roll the wax between your fingers for a while, it becomes soft. What state of matter is the softer wax? Is it possible for the wax to change without changing its state?
Answer:
An amorphous solid does not have a definite melting point; instead, it melts gradually over a range of temperatures, because the bonds do not break all at once. This means an amorphous solid will melt into a soft, malleable state (think candle wax or molten glass) before turning completely into a liquid.
Explanation:
Hope this helps
May I get braineist pls?
What is the gravitational force between two objects of masses 20kg and 50kg separated by a distance of
4m?
Answer:
4.16875×10^-9
Explanation:
given,
mass(M1)=20kg
mass(M2)= 50kg
distance(d)=4m
gravitational constant value (G)=6.67×10^-11
we know,
gravitational force=(Gm1m2)÷d^2
=(6.67×10^-11×20×50)÷4^2
=(6.67×10^-8)÷16
= 4.16875×10^-9
why does polishing the surface of a metal extend fatigue life
Answer:
they are machined with shape characteristics which maximize the fatigue life of a metal.
Explanation:
they are highly polished to provide the surface characteristics which enable the best fatigue life.
The frequency of a wave is 4hz. If the wavelength is 2m how fast is the water moving?
I need the Formula,Known,Substitute & Solve Answer with Units
Answer:
This is the answer that I got
Explanation:
Hope it is right.
A bullet of mass 20 g has its kinetic energy equal to 400 J. Find the speed of the bullet.
Answer:
m=20g=0.02kgK.E=400J[tex]\\ \sf\longmapsto KE=\dfrac{1}{2}mv^2[/tex]
[tex]\\ \sf\longmapsto \dfrac{1}{2}(0.02)v^2=400[/tex]
[tex]\\ \sf\longmapsto 0.01v^2=400[/tex]
[tex]\\ \sf\longmapsto v^2=40000[/tex]
[tex]\\ \sf\longmapsto v=200m/s[/tex]
If the energy in a mechanical wave increases or decreases, what is also going to increase or decrease? A wavelength B amplitude с frequency d refraction
Answer:
i think wave lengh not 100% sure tho
If the energy of the mechanical wave will increase or decrease, then the wavelength will also change accordingly. Hence, option A is correct.
What is Wavelength?The distance between two identical locations (adjacent crests) in successive cycles is known as the wavelength, and it is used to describe waveform signals that are transmitted over wires or into space. Typically, in wireless systems, this length is specified in meters (m), centimeters (cm), or millimeters (mm). The wavelength is more frequently described in nanometers (nm), which are units of 10⁻⁹ m, or angstroms, which are units of 10⁻¹⁰ m, for infrared (IR), visible light (UV), and gamma radiation.
Frequency, which is defined as the number of wave cycles per second, and wavelength have an inverse relationship. The wavelength of a signal decreases with increasing frequency, or we can say that wavelength and refractive index are inversely proportional to each other.
To know more about Wavelength:
https://brainly.com/question/13533093
#SPJ2
What would happen to a 100N gravitational force if both masses were doubled and the radius were
doubled
The force winds up unchanged, at 100 N.
Something has a mass of 40 kg and a velocity of 1 m/s
How much kinetic energy does it have?
Part 2: If it doubles its mass, will its KE also double?
[tex]\\ \sf\Rrightarrow K.E=\dfrac{1}{2}mv^2[/tex]
[tex]\\ \sf\Rrightarrow K.E=\dfrac{1}{2}(40)(1)^2[/tex]
[tex]\\ \sf\Rrightarrow K.E=20J[/tex]
Part 2:-m=80kg[tex]\\ \sf\Rrightarrow K.E=\dfrac{1}{2}(80)(1)^2[/tex]
[tex]\\ \sf\Rrightarrow K.E=40J[/tex]
Yeshow to find acceleration with mass and force calculator
Use the equation a = F/m, where an is the acceleration, F is the force being applied, and m is the mass of the object, to calculate acceleration using mass and force. Calculating the acceleration is as simple as dividing the force by the mass.
What is Newton's second law of motion?Newton's Second Law of Motion states that the acceleration of an object is directly proportional to the force applied on it, and inversely proportional to its mass. The mathematical representation of this law is:
F = ma
where F is the force applied on an object, m is the mass of the object, and a is its acceleration. This law implies that the greater the force applied on an object, the greater its acceleration will be, and that the acceleration of an object will decrease as its mass increases, given a constant force.
This law helps to explain the behavior of objects under the influence of external forces. It is used in many areas of science and engineering, including mechanics, physics, and aerospace. Understanding the relationship between force, mass, and acceleration is fundamental to the study of mechanics and the design of machines and structures.
Here in the Question,
To find acceleration using mass and force, you can use the following steps:
1. Determine the force acting on the object. This can be done using a force meter, a scale, or by calculating the force using the formula F = ma, where F is the force in newtons (N), m is the mass of the object in kilograms (kg), and a is the acceleration in meters per second squared (m/s²).
2. Measure the mass of the object in kilograms. This can be done using a scale.
3. Use the formula a = F/m to calculate the acceleration of the object. Rearrange the formula to solve for a: a = F/m.
5. Plug in the values for force and mass and solve for acceleration. For example, if the force acting on an object is 20 N and the mass of the object is 5 kg, the acceleration can be calculated as follows:
a = F/m
a = 20 N / 5 kg
a = 4 m/s²
So, the acceleration of the object is 4 meters per second squared.
It's important to note that the units of force and mass should be in the correct SI units (newtons and kilograms, respectively) to ensure the correct unit for acceleration (meters per second squared).
Therefore, To find acceleration using mass and force, use the formula a = F/m, where a is the acceleration, F is the force applied, and m is the mass of the object. Simply divide the force by the mass to calculate the acceleration.
To learn more about Newton's law of motion click:
brainly.com/question/29775827
#SPJ2
I have two questions. I hope anyone can help me <3 Question 8 & Question 9.
Answer:
i have not study it till now
Explanation:
sorry i don't know
A car takes off from rest takes of from rest and covers a distance of 80m on a straight road in 10s.Calculate the magnitude of its acceleration.
Answer:
The magnitude of its acceleration is 1.6 m/s^2.
Hope you could get an idea from here.
Doubt clarification - use comment section.
What is velocity? Explain.
Answer:
The velocity of an object is the rate of change of its position with respect to a frame of reference, and is a function of time. Velocity is equivalent to a specification of an object's speed and direction of motion (e.g. 60 km/h to the north).Line segment Q R , Line segment R S and Line segment S Q are midsegments of Î"WXY. Triangle R Q S is inside triangle X Y W. Point R is the midpoint of side X Y, point S is the midpoint of side Y W, and point Q is the midpoint of side X W. The length of Q R is 2. 93 centimeters, the length of R S is 2. 04 centimeters, and the length of Q S is 2. 28 centimeters. What is the perimeter of Î"WXY? 11. 57 cm 12. 22 cm 12. 46 cm 14. 50 cm.
The perimeter of ΔWXY is : ( D ) 14.5 cm
Calculating the perimeter of ΔWXY
QR = WY / 2
RS = XW / 2
QS = XY / 2
Given that : QR = 2.93 cm , RS = 2.04 cm, QS = 2.28 cm
Therefore
Perimeter of ΔWXY = ∑ WY + XW + XY
= 2SR + 2QS + 2QR
= 2(2.04) + 2(2.28) + 2(2.93)
= 14.5 cm
Hence we can conclude that the perimeter of ΔWXY = 14.5 cm
learn more about perimeter calculations : https://brainly.com/question/24744445
Answer:
The name of the shape on the right is M prime N prime O prime P prime Q prime R prime S prime because it is the image of the shape on the left.
Explanation:
The gravitational force between two asteroids is 6.2 × 108 N. Asteroid Y has three times the mass of asteroid Z.
If the distance between the asteroids is 2100 kilometers, what is the mass of asteroid Y?
Answer:
1.1x10¹⁶ kg
Explanation:
Let m = mass of asteroid y.
Because asteroid y has three times the mass of asteroid z, the mass of asteroid z is m/3.
Given:
F = 6.2x10⁸ N
d = 2100 km = 2.1x10⁶ m
Note that
G = 6.67408x10⁻¹¹ m³/(kg-s²)
The gravitational force between the asteroids is
F = (G*m*(m/3))/d² = (Gm²)/(3d²)
or
m² = (3Fd²)/G
= [(3*(6.2x10⁸ N)*(2.1x10⁶ m)²]/(6.67408x10⁻¹¹ m³/(kg-s²))
= 1.229x10³² kg²
m = 1.1086x10¹⁶ kg = 1.1x10¹⁶ kg (approx)
how to find velocity with constant acceleration
Answer:
velocity = distance / time
example:
if a body moves "20" meters in "2" seconds
, then it's velocity = 20/2 = "10m/s"
why does rhododendron not grow well in the terai region of nepal give reason
Answer:
Tge Rhododendrob is the national flower of Nepal. The hills and mountain sides ranges of Nepal are decorated with diff colours and shapes
assume that the hubble constant is 72 km/s/mpc. if a galaxy is 100mpc away, how fast is it moving away from us?
The galaxy is 7200 km/s moving away from us.
A Hubble is a large telescope in space.
The question can be solved using the formula below
⇒ Formula
v = Cd........................ Equation 1⇒ Where:
v = Speed of the galaxyC = Hubble constantd = Galaxy's distance⇒ Given:
C = 72 km/s/mpcd = 100 mpc⇒ Substitute these values into equation 1
v = 72(100)v = 7200 km/s.Hence, the galaxy is 7200 km/s moving away from us.
Learn more about Hubble here: https://brainly.com/question/14615983
3. A(n)______ is someone who travels to new places or does new things. A. explorer B. thrill C. expedition D. research
Answer:
explorer
Explanation:
Answer:
a) EXPLORER
Explanation:
An explorer is someone who travels to new places or does new things.
please help quickly,the picture and choices are above.
Answer:
C because it make sens
C the light wave traveled through ice and then through a Dimond.
which statement is not correct about force.
A, force causes deformation
B, force xauses accleration
C, if there is no force, there is no motion
D, force emerges due to interaction.
Answer:
c
Explanation:
without force motion won't take place